Filter Results By:
Products
Applications
Manufacturers
Low Pass Filters
Refine signal, allowing the transmission of signal below a specific corner frequency, while attenuating the frequencies above.
See Also: Filters, Filter / Amplifiers, EMI Filters, Programmable Filters
-
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
Low-Pass Filters
Low-Pass Filters from Analog Devices are specifically designed to reject higher frequency noise and unwanted signals while allowing desired signals to pass through. Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) devices preconfigured for low-pass filtering. These integrated low pass filters feature a wide range of cutoff frequencies and response characteristics.
-
product
"Standard" RF Low Pass Filters
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
product
Analog to Digital Converter
7418/7419
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20 mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-3F
Programmable, 2-Channel Low-Pass Filter Module. The AAF-3F is designed for use with the AAF-3M and AAF-3PCI filter boards.
-
product
Precision Low-Loss Multiplexers
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
product
Low Power Analog to Digital
7430
Smart A/D for thermocouples, thermistors, RTD's, strain and pressure gauges8-channels of 16-bit A/D resolutionEliminates trimpot adjustments by using software calibrationPerforms concurrent 32-bit floating point operations to minimize host computer loadingEach channel is software programmable for sensor type, gain, low-pass filtering, scan rate
-
product
Amplifier/Filter Module
SCS-815
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Frequency Counters
-Frequency Range : 0.2Hz to 5.5GHz Built-in CMOS Gate Array Fast, High-Resolution, 10 Digits Green LED Display Microprocessor Controlled Reciprocal Technique for Low Frequency Resolution Self Diagnosis Routine Total, RPM Function, Period Low Pass Filter(100KHz, -3dB) Rs-232c Interface(Option)
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Flexible Leakage/Line Current Tester
RLM-10+
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
product
Smart Analog to Digital
618/619
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
16-Channel Anti-Alias Low-Pass Filter Card
AAF-16
The AAF-16 is a 16-channel anti-alias low-pass filter card series for front-end signal conditioning in PC-based data acquisition systems.
-
product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
product
Precision Dual-Channel Compact Filter/ Amplifier System
PFA-2
he PFA-2 is a compact, rugged, and versatile dual-channel precision filter/amplifier. The low-noise, high common-mode rejection balanced differential input with programmable AC/DC input coupling is ideal for conditioning static or dynamic signal inputs. Sharp, programmable 6-pole low-pass precision filters support two response characteristics which are optimized for making time-domain or frequency-domain measurements.
-
product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
-
product
Lowpass Filters
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
Dual Filter
Trig-TekTM 550D
Two channels with variable high pass and low pass filters in a module 7" high x 2.6" wide
-
product
Lowpass Filters
K&L Microwave provides lowpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
product
Dual Channel Multi-Band FM Tracking/Data Receiver In Modular Style Housing
LS-27-B
The Lumistar LS-27-B Modular Dual Channel Tri-Band Tracking and Data Receiver is Lumistar’s third generation of modular high performance FM Receivers. This wideband designs supports one or two independent channels of PCM with data rates up to 20Mbps. The unit includes both an optional FM demodulated output for PCM data, and standard programmable AM/linear AGC outputs for auto-tracking receivers. The design offers 8 IF Bandwidths and 8 Video Filters per channel for each receiver.AC coupling with a low pass filter is employed to ensure a high quality data link with long strings of NRZ-L ones or zeroes. The unit provides a software selectable 10 MHz reference I/O port forlocking local oscillators to a high precision external source or to arrange multiple units in a master/slave arrangement. The receiver’s control and status is achieved via Ethernet, USB or auto-switched RS-232 (or “4-wire” RS-485 in place of 232). When utilizing the RS-422 interface, multi-drop configurations can be accommodated.
-
product
1.3GHz Frequency Counter
Model 1122 / 1122X
- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)
-
product
Filtered Analog Input Expansion Board
MSXB 048
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
product
Clamp Meters
0.001 mA Current Resolution, Comply With IEC61557-13: Class 2, ≦ 30A/m, True RMS Measurement For All Applications, Low Pass Filter Function
-
product
EMI/EMP Connectors
Filter connector series includes EMI/ EMP/ESD circular, ARINC, D-subminiature and micro-D connector styles. They can be combined with high energy TVS diode technology to achieve lightning and EMP transient protection. Smiths Interconnect's EMI filter connectors use multi-layer ceramic capacitor arrays together with inductive materials to realize robust, high performance low pass filter networks. Where required, transient protection can be combined with EMI /RFI filtering to provide maximum protection. The diodes as well as the EMI filter are packaged separately so the construction of the connector remains modular.
