Filter Results By:
Products
Applications
Manufacturers
-
product
FireBird Camera Link Frame Grabber (2xCLD-2PE8)
AS-FBD-2XCLD-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Wireless Transmission
Wireless transmission is a form of unguided media. Wireless communication involves no physical link established between two or more devices, communicating wirelessly. Wireless signals are spread over in the air and are received and interpreted by appropriate antennas.
-
product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
product
Torque Systems
The Drive Plate Torque System uses a low power radio link to transfer digitised strain measurements from a rotating wheel hub to a stationary antenna mounted nearby. The signals are passed to a receiver where they are decoded and output as CAN bus messages and analogue outputs.
-
product
Director's LCD Monitor with Wireless RF Link
EZ-ROAM D
The highly portable "EZ-ROAM D" has been designed for life on the road, and is ruggedly constructed in an extruded aluminium case sealed to IP67, and tough enough to take every day knocks and bumps. Battery powered (and with an external dc input too), the EZ-ROAM D with it's 7" LCD provides robust diversity radio reception, whilst the recessed controls offer selection between video inputs, 16:9 or 4:3 aspect ratios, Horizontal & Vertical flip, and stereo audio monitoring. There is even an RX OP on BNC.
-
product
Enterprise/ Carrier Transmission Tester
UniPRO MGIG1 Series
Designed for comprehensive turn-up testing, monitoring and troubleshooting of fixed line, mobile, microwave and wireless carrier Ethernet links. UniPRO MGig1 is suitable for use on any backhaul link at speeds of up to 1 Gb/s.
-
product
FireBird Camera Link Frame Grabber
AS-FBD-1XCLD-2PE4L
FireBird Camera Link Deca Low Profile is a member of Active Silicon's state-of-the-art FireBird frame grabber family. The low profile design allows the FireBird Low Profile board to be used in small embedded PC enclosures and rackmount cases where full height PC cards are not suitable. A full height bracket option of this product is available for use in standard PC form factor enclosures. FireBird is designed for ultimate performance providing the very fastest image acquisition without any CPU intervention using the latest FPGA families, DDR3 memory, and a fast Gen2 PCI Express interface.
-
product
Cyber Threat Assessment Program
Scientific Research Corp. STI Division
SRC provides threat assessment support focused on cyber threats that may impact the ability to wirelessly link with other systems. This activity supports the development of test and evaluation capabilities important to not only identifying current deficiencies but also for developing next generation systems.
-
product
PXI 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-614B-010
This 2-bank, 64-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI/PXIe High Density 2A Multiplexer, 16-Bank, 4-Channel, 2-Pole
42-614D-002
The 40-614D-002 (PXI) and 42-614D-002 (PXIe) 16-bank, 4-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
LinkExpert Software
LinkExpert enables complete control and management of Teledyne LeCroy's family of Protocol Analyzer and Exerciser hardware. LinkExpert provides a convenient interface to run Compliance, Conformance and Validation tests on PCI Express (PCIe) and SAS (Serial Attached SCSI) links. The LinkExpert software interface is provided free of charge and includes as standard, several validation tests for PCIe Hosts (Root Complexes) and Devices (End Points).
-
product
SPIC-300 Spectral Irradiance Colorimeter
Hangzhou Everfine Photo-E-Info Co., LTD
With an internationally patented design at its core, the SPIC-300 is ushering in a new era of on-site spectral measurement. It has high-end intelligent configuration, one-click operation and analysis, real-time data reading, not only applicable to field, construction, indoor, workplace, shopping malls and other on-site lighting measurement, but also for lighting product development, quality inspection, production line monitoring links.
-
product
Pre-Selectors for EMC test
These Pre-Selectors are high specification, switched band filters which track the scanning of the EMC Analyser. Control is via USB link from the Laplace EMCEngineer software supplied with SA1002 and SA3000 analysers. Installation and operation is completely automatic, and the filters will synchronise with the analyser scan without any operator intervention. A front panel switch allows manual operation if required.
-
product
915MHz Data Link Test Set
Kratos Defense & Security Solutions, Inc.
The 915MHz Data Link Test Set (DTS) is a portable, industry leading test instrument used for verification of Data Link Subsystem Replacement (DLS-r), Army Ground Station Unit (GSU), and other 915MHz Gulf Range Drone Control Systems (GRDCS) communications equipment in compliance with the GRDCS Data Link Format Specification.
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
product
Handheld Optical Power Meter
JW3402
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3402 Optical Power Meter is a highly cost-effective portable power meter and it’s newly launched by the Joinwit Company. It can be used for the optical power measurement within the wavelength 800～1700nm. JW3402 also has a wide measurement range which is more than 70dB. It’s designed with the common wavelength calibration points, such as 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. The instrument is widely used in fiber-optic link construction, testing and maintenance.
-
product
Tube Mount Transmitter / DIN Rail Receiver
The 28670XX-DRX Series are unidirectional wireless systems that comprise a transmitter and a receiver.This Drexelbrook transmitter accommodates two digital signals in the range from 5 to 30 V AC/DC or 100 to 240 V AC and one analog current signal (4-20 mA). These signals are available for further processing at the receiver in the form of two relay contacts and one 4-20 mA current output. In addition, a third relay in the receiver diagnoses the status of the wireless connection (RF link).
-
product
VTAC, Insert, Receiver/ITA, SIM, Right Angle, 8 Pos, 1 Slot
610151104
This insert contains 8 right-angle VTAC high speed contacts and is designed to mount directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 1 of the 34 slots in this module. Available in a set with VTAC pass-thru insert as 610151106. Use the video link on this page for help installing this insert on a PCB.
-
product
Phoenix PMC Camera Link Frame Grabber
AS-PHX-D24CL-PMC32-B
Phoenix-Dig24CL is a PCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of Base configuration, i.e. single 8- to 16-bit data, through 8-bit RGB, to dual tap 12-bit sources.
-
product
PXI 2A Multiplexer, 2-Bank, 8-Channel, 8-Pole
40-614C-013
This 2-bank, 8-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the information it reads from the module and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
Satellite Carrier Reconnaissance and Analysis System
SCL-SACRAS
Shoghi’s Satellite Carrier Reconnaissance and Analysis System (SCL-SACRAS) is capable of detecting Point-to-Point satellite links, which work for international Voice networks, GSM Abis backhaul links, IP links and VSAT networks of major VSAT manufacturers including iDirect, Hughes, Gilat, Eastar Romantis, Comtech; including the various types of proprietary protocols and services running on them.SCL-SACRAS can be utilized for the carrying out the detailed reconnaissance of satellite carrier frequencies running on various target satellites, for identification of target carriers for regular monitoring which are of the customer’s interest. Military or intelligence agency customers can utilize this system to identify the target links on respective satellites for continuous monitoring, using the Shoghi VSAT Monitoring System.
-
product
Interfaces
Channel link cable. Allows two scopes to be linked together to give 4 analog and 16 digital channels. Requires the four channel software to be installed.
-
product
PXI Bus Expanders
MXI-4E
The MXI-4E PXI Bus Expander allows for direct control of PXI systems from a PCI slot in a desktop computer or server. MXI-4E interface cards can also be used for linking multiple PXI chassis. MXI-4E technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
product
Keysight N7800A Test Management Environment (TME) Software
Special recommended calibration options: The N7800A software calculates point-to-point ISO GUM measurement uncertainty. The special “H-series” calibration options in the link below provide lower measurement uncertainties through use of direct comparison to devices directly characterized by NPL or NIST (or another NMI), along with data on a CD for easy import into the N7800A (avoids manual entry). The overall resulting N7800A measurement uncertainty then incorporates this lower device uncertainty in the overall calculated uncertainty. For more information on the special options please view this spreadsheet N7800A Special Calibration Matrix.
-
product
Digital Optical Transport
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
-
product
PXI 2A Multiplexer, 8-Bank, 4-Channel, 4-Pole
40-614B-005
This 8-bank, 4-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
FastCamera
FC300
The FastCamera 300 is a high-speed 3 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
product
Testing
Apogee Labs offers a wide variety of modular chassis types used for test applications with various Data Link Test Modules.
