Filter Results By:
Products
Applications
Manufacturers
-
product
Emergency Battery Test Fixture
TA-60
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
product
Architectural Preset Stations
SceneStation
Interactive Technologies, Inc.
SceneStation sets a new standard for full-featured, easy to use, cost-effective DMX lighting control. SceneStation is entirely self-contained in a single gang wall switch sized unit. Perfect for restaurants, high-end residential, trade show booths and more, SceneStation can control nearly any DMX device (RGB fixtures, moving lights, dimmers, effects, etc.), while also remaining very simple for the end user.
-
product
LED Light Tester
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
product
Electronic AC/DC Voltage Tester
ET60
The ET60 voltage tester requires no batteries as it measures AC/DC voltage up to 600V in electrical circuits, outlets, light fixtures and anywhere else AC/DC voltage testing is required.
-
product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
product
Light source
UVM-MP
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
product
Outdoor Surface Mounted
HYLO
Available as uplighter, downlighter and up-/downlighter. Choice of multiple colours of LED light sources and a variety of beam angles. The up/down version offers the possibility to use two different colours of light and two different beamangles within one single fixture. Up to 80% energy savings compared to traditional light sources.
-
product
VP Power Meter
UVP-365
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
product
Photometric Testing Services
LLI. offers a wide variety of services to fulfill your photometric, color and electrical testing needs. Using our custom, rotating mirror, Type-C goniophotometer, in combination with various integrating spheres, we are able to test many different types of lighting fixtures and light sources. LM-79 -08 Test & LM-80 Test, SSL Photometry Testing, Energy Star®, CEC Title 24, DesignLights Consortium® (DLC), Custom Tests and UL / ETL Safety Test Consultation.
-
product
Test Accessories
By combining the latest in LED technology with the unmatched illuminating dynamics of prismatic glass, this High Bay LED luminaire brings a superior, incomparable proficiency and reliability to the table. With its remote driver capability, the TDK HBLED-540 High Bay LED Light Fixture is ideal for EMC chambers with minimal RF emissions.
-
product
Circuit Breaker Finders
Is a small battery-operated electronic tool with two parts—a transmitter and receiver. It is designed for single purpose—to identify which circuit breaker in a main service panel serves a particular outlet or light fixture to which the tool's transmitter is connected.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Light Sources
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
product
Light Meter
2330 LX
Standard Electric Works Co., Ltd
● Wide range for measurements up 40000 lux and 4000 fc.● 0.01 lux and 0.001 fc resolution for accurate low light level measurements.● Light sensor cover is included for preserving sensor life.● Auto off function.● Data hold function.● Low battery indication.● Over range indication.● Auto-ranged.● Manual-ranged.● Calibration mode is provided.● 9V battery system.● Selection key for lux and fc.● The spectral sensitivity close to CIE photopic curve.● Ideal tool for workplace, clean-room and computer room light testing.● Video, photographic, office, classroom, and architectural uses.
-
product
Test fixtures
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
product
Light Meters
LXP-10B
The new LXP digital light meter family allows for a very precise measurement of illuminanace. Thanks to very high resolution (resolution 0.01 lx ) allows for escape route emergency light measurement. All of three light meter have built-in memory for measurement result storing, and additional function making work much easier.
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
-
product
Custom Fixtures
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
-
product
Automated Checking Fixture
AutoGauge-ACF
Perceptron has combined over 35 years of metrology and manufacturing experience to create a truly absolute, correlation-free checking fixture for your plant floor. Virtually everything about AutoGauge-ACF is automatic – from robot path generation that enables quick setup and changes to the display of measurement results for real-time analysis.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
