Filter Results By:
Products
Applications
Manufacturers
LCD
Analyze Liquid Crystal Displays.
-
product
Digital RCD Tester
1612 EL
Standard Electric Works Co., Ltd
●Microprocessor-controlled●Extra large LCD (78 × 67mm)●Very low power consumption●50Hz and 60Hz operation●Accurate digital readout of disconnection time●Over temperature protection●Over voltage protection●Fuse protection●Zero crossing circuitry permits testing at 0° or 180°●Auto power off●Backlight function●Wiring polarity indicator●Measures voltage between Line and Earth before testing●Frequency measurement indication
-
product
PH Meter / Tester, 0pH to 14pH, 0.01, 0.2, 400 ms, 0 °C, 50 °C
72-6783
The 72-6783 is a 0 to 14pH Meter with 12.5mm LCD display. Any combination of pH electrode and male BNC connector can be used. pH meter included with battery.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL D
The 72-7770 CAL D from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
Laser Distance Meter with Clinometer
TRUPULSE 200
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LCD Display in scope: target and measurement data at one glance*Range to non-reflecting targets 1.000m*Range to reflecting targets 2.000m*Accuracy in range ± 20cm (± 1m to weak targets; shown in display)*Accuracy in slope ± 0,25°*RS 232/Serial interface and with Bluetooth*IP protection IP54
-
product
Watertight Belt-Pack Transmitter
WM
Designed for wet or dusty environments, the WM transmitter features O-ring sealed battery compartments and input jack, a compression sealed antenna port and gasket sealed control panel and back cover. Dual AA batteries provide twice the operating time of earlier watertight transmitter designs. Larger membrane switches and control panel and a highly visible, backlit LCD enhance the user interface.
-
product
Compact OTDR
◇ 5.6-Inch outdoor-enhanced touchscreen, 7.4V/4.4Ah Lithium battery◇ Event Dead zone as lower as 1.5meter◇ Combined multi-dynamic range and wavelengths◇ Muti measurement mode, support Touching LCD and pressing keys◇ Warning function could prevent OTDR module from being damaged by optical signal in fiber.◇ Realtime measuring function, convenient to monitor the splicing process◇ Integrated 10mw Visual Fault Locator◇ Support English/ Chinese input, adopts friendly input interface, totally simulate the computer keyboard input ◇ Integrated with 8GB internal memory, more than 80,000 groups curve storage◇ PC remote access and control function is available, which support the printing work of the measurement report
-
product
Samples Preparation (Polisher/Grinder)
* LCD displays all the cutting data.* The diameters of specimens to be cut range from 5 to 8mm (1008:100mm) and the cutting capacity reaches 100x200mm.* Manual cutting and automatic cutting can be changed over at random. * Large cutting chamber & tempered-glass view window.* Non-burnt movable cutting mode which greatly improves cutting quality.● Automatic retract at the end of cutting operation.● Dual-direction feed which increase the depth of cutting.
-
product
CT / PT Analyzer
CTPTA-504
UDEYRAJ ELECTRICALS PRIVATE LIMITED
UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.
-
product
Digital Vibration Tester
DVM-1000
Quick accurate analysis for checking balance and alignment of a rotating object. Large LCD display Statistics: Mean, Max, MIN, No. of Measurements and Std deviation Inch/Metric Conversion with the push of a button Max Hold Function Regulated Output(AC output 2.0v peak full scale
-
product
Folding Tester
DRK111B
Shandong Drick Instruments Co., Ltd.
DRK111B Folding Tester is designed according to relevant standards and adopts modern mechanical philosophy and computer processing technology. It has LCD display function, various parameters setting function, conversion, adjust, memory, printing, and other functions.
-
product
Digital Multimeter
189 DM
Standard Electric Works Co., Ltd
● 4000-count LCD.● Auto ranging.● Voltage, Resistance, Continuity, Diode measurement.● Frequency, Capacitance, Current measurement.● Wide range for capacitance test : 0~4000μF.● Data hold function.● Low battery indication.● Over range indication.● Auto power off.● With a convenient stand for viewing.● Compact and lightweight.
-
product
Electrical Safety Testers
STW-9900 Series
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
product
Well Camera
Well-Camera.1
Taking advantage of our vast experience in designing and manufacturing TV-inspection systems for boreholes and wells, we created the innovative WELL-CAMERA Series that follows all our Customer’ requests about an easy use, reliable, compact and lightweight instrument for field operations. The complete system consist of: reel and camera head, display unit with integrated LCD, USB2 grabber board and microphone, battery charger. Pictures, movies and comments can be saved to any external laptop.
-
product
Composite Damage Checker
35RDC
The handheld 35RDC is a simple Go/No-Go ultrasonic instrument designed to detect subsurface defects caused by impact damage on solid laminate aircraft composite structures. The 35RDC features a backlit LCD that displays the word GOOD if no subsurface damage is found or the word BAD when it detects subsurface damage.
-
product
Mini Carbon Monoxide Gas Detector
Model - KM CO-910
Kusam Electrical Industries Limited
KM-CO-910 Carbon Monoxide meter detects the presence of Carbon Monoxide (CO) & measures concentrations between 1-1000 parts per million(PPM). The meter indicates the presence of CO by a reading on the LCD & a beeper tone. The beeper function much like clicking of a geiger counter: above 200PPM, the beeper sounds continuously with the concentration of CO; from 35PPM to 200PPM, the beeper sounds discontinuously with the concentration of CO.
-
product
Handheld UV Imaging Solution
UVCorder™
The compact unit is designed for viewing scenes in the near-UV waveband in real time on a 3.5-inch LCD display and for acquiring near-UV digital video and stills quickly and easily. Oculus Photonics' ultraviolet camera module (UVM) features enhanced ultraviolet response in the 300-400nm range, with a peak response at 370nm, and excellent rejection of visible and infrared light.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL
The 72-7770 CAL from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
Wood / Building Moisture Meter
PeakTech Prüf- und Messtechnik GmbH
High quality wood and material moisture meter, which is characterized by its ease of use and universal applicability. The device has an LCD display, in which measured values of humidity and ambient temperature are displayed. In addition, it is equipped with an LED display, which enables a quick good-bad assessment of the measured values.
-
product
Infrared Thermometer
CENTER 352
Simple One-Handed Operation, Laser Targeting, LCD With Back Light, °C/°F Select Switch, Laser ON/OFF Switch, Automatic Power Off, Display Hold Function
-
product
Handheld Water Quality Meters
LAQUA PC210
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
product
Data Diver
MT-8006B
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
product
Booster and In-line Amplifier
Amonics' EDFA range adopts unique design to produce maximum signal gain and saturated output power while maintaining low noise figure, enabling test capabilities in system or component level manufacturing and characterizing processes, as well as facilitating highly demanding R&D applications. The compact turnkey benchtop or 19" rackmount unit incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power control knob and optical connectors. An integrated RS232 computer interface enables easy control, diagnostic functions and data acquisition.
-
product
Heated Type THC Analyzer
MEXA-1170HFID
With 14 selectable ranges - from 0-10 ppmC to 0-200,000 ppmC - MEXA-1170HFID can measure direct, CVS/tunnel-diluted, and evaporative-emission samples.A ten-key control pad and a color LCD make it easy to monitor the test data. Data transfer to a remote computer is possible via RS-232 or an optional analog output.
-
product
Steam Aging Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Steam aging test chamber is a climatic test machine used to judge the products performance to resist extreme circumstance under high temperature, high humidity and high pressure during the transportation, storage and usage. The principle is very simple, water in the tank is heated turning into steam to form a simulated test environment under specified temperature and humidity. Specimens are placed into the drawers of machine to carry out test lasting for preselected time. It is applicable to electronic connectors, semiconductor IC, transistor, LCD, diodes, resistances etc.
-
product
Viscometer
LS
Chongqing Lushun Scientific & Technological Development Co., Ltd.
This instrument is sophisticated. It adopts advanced mechanical design and manufacture techniques, and microprocessor controlling technologies, it can accurately collect test data; Take a blue background light, ultra-brighten LCD as its display, so it can display test data intuitively; Designed with a RS232 port, so it can print out test data through a printer, and it can communicate with a computer using the software attached. It is sensitive, reliable, beautiful and convenient to be operated. It is used to determine absolute viscosity of Newton liquids and apparent viscosity of non-Newton liquids. It can be widely used for determining viscosity of grease, paint, plastic, medicine, dope, adhesive, and washing solvents, etc.
-
product
Wide Range Ohmmeter
PAS-853B
- Wide Resistance Measurement Range from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period Control- Automatic or Continuous Electrification ControlRugged High Performance 80 inches (200cm) Test Leads Included- Powered by one long lasting 9V Alkaline Battery- Large, Easy to Read LCD Display- Meets requirements of ESD Association Standards for material and audit resistance measurement requirements- Certificate of Calibration Traceable to NIST included
-
product
Digital ELCB (RCD) Tester
1813 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● Suitable for domestic version.● Better than 3% accuracy (current).● Menu-driven.● Accurate digital readout of disconnection time.● Accurate digital readout of disconnection sensitivity.● Automatic data hold function.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● 60Hz available.
-
product
Insulation & Multifunction Tester (LCD Display)
1151 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at Switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-null key.● Test Auto-stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Leeb Hardness Tester
THL210
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data（impact times:32～1）. Lower limit setting and sound alarm. Material of “cast steel” is added; HB values can be read out directly when D/DC impact device is used to measure “cast steel” work piece. Printer be separated from main unit and copies of testing results can be printed as required. Normal battery AAA and big power store while USB connected and charging controlling circuit. Inbuilt function of Software Calibration.
-
product
Calibrator, Calibrated, Current, 185 mm, 78 mm, 38 mm, ± (0.25% FS +1 digit), ± (0.5%FS + 1 digit)
72-6694 CAL
The 72-6694 CAL from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
