Filter Results By:
Products
Applications
Manufacturers
JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
product
JTAG Emulators
XDS100v2 Series
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
product
Advanced JTAG Emulators
Blackhawk offers JTAG Emulators ranging from entry level to full-capability debug probe models supporting System Trace (STM), starting at $99. This includes XDS100v2, XDS200 and XDS560v2-class models that are compatible with Code Composer Studio.
-
product
JTAG Emulator
Spectum Digital XDS510-USB
The Spectrum Digital XDS510 JTAG emulator is low cost and has a USB powered interface.
-
-
product
JTAG Emulator for BAE Systems RAD750 Microprocessors
CodeRunner JTAG Emulator
Designed for the most hazardous high radiation environments, the BAE Systems RAD750 radiation hardened PowerPC microprocessor is the most advanced processor offered to the space community. From the Mars Reconnaissance Orbiter to the Curiosity Rover, the RAD750 microprocessor has proven time and again to lead the industry in quality, performance, and cost.
-
product
High-Performance JTAG Emulators
XDS560 Series
Blackhawk XDS560-class models are offered with PCI, USB, and Ethernet host interfaces. These XDS560 models support the first generation of TI XDS560-class high-speed JTAG connection between Code Composer Studio and the target device.
-
product
JTAG Emulator
Spectum Digital XDS560v2-STM
The Spectrum Digital XDS560v2-STM emulator has System Trace capability, along with a USB powered interface.
-
product
JTAG Emulator
Blackhawk XDS560v2
The Blackhawk XDS560v2 STM emulator has System Trace capability, along with USB powered and LAN interfaces.
-
product
JTAG Emulator
Spectum Digital XDS510-USBPlus
The Spectrum Digital XDS510-USBPlus enhanced JTAG emulator is low cost, along with a USB powered interface.
-
product
JTAG Emulator
Blackhawk USB510L
The Blackhawk USB510L JTAG emulator is low cost, and has a USB powered interface.
-
product
JTAG Emulator
Blackhawk USB560v2
The Blackhawk USB560v2 STM emulator has System Trace capability, along with a USB powered interface.
-
product
Emulator
GCI E84
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
product
JTAG Visualizer
JTAG Visualizer is an advanced graphical viewer and data management system for PCB schematics and layouts. Visualizer integrates seamlessly with the JTAG Technologies family of boundary-scan products, such as the ProVision application development platform, and accepts PCB data from a variety of CAD, CAM and EDA tools. In design Visualizer provides DfT (design for test) feedback to the user by enabling a graphical view of fault coverage on their design. In manufacture and test Visualizer can be used to highlight faulty nets (short circuits, opens, stuck-ats etc.) in both layout and schematics views.
-
product
Protocol Emulations
Message automation and protocol simulation test tool that supports simulation of a variety of protocols (VoIP/IP, TDM, Analog, Wireless) all within a single framework. The application includes various test plans and test cases to support the testing of real-time entities
-
product
Emulator
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
product
JTAG / BDM Instrumentation
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
product
JTAG Boundary-Scan Controllers
Corelis has developed a wide range of high-performance boundary-scan controllers that are compatible with buses such as USB 2.0, PCI, PCI Express, and Ethernet. Many of Corelis’ boundary-scan controllers operate up to 100 MHz sustained TCK frequency.
-
product
Network Emulators
Rohde & Schwarz offers class-leading signaling testers. We established our position as leading supplier of LTE communications testers with the popular, all-in-one R&S®CMW500 platform. Now we are building on the expertise that enabled its success with the high-performance R&S®CMX500 radio communication tester.Secure the industry-leading wireless network emulators for your 5G NR and legacy technology challenges – from R&D design stages up to end-to-end application testing, production and conformance tests.
-
product
LLDP Emulation
The IEEE 802.3 specifications require that Type 2, Type 3, and Type 4 PDs implement PoE LLDP and use the Power via MDI TLV for power negotiation. This requirement therefore applies to any PD that draws more than 13 watts. The PDA-600 family includes an option to flexibly emulate any PSE while capturing and analyzing the LLDP power negotiation protocol from a PD.
-
product
LLDP Emulation And Analysis
The optional LLDP Emulation feature allows a PSA-3000, PSL-3424L, or PSL-3000 test port to behave just like an 802.3at or 802.3bt PD that uses LLDP to convey its power demands. 802.3 PoE LLDP is a special variant of LLDP protocol that involves handshakes and protocol timing between a PSE and a PD.
-
product
Sensor Signal Emulator
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
product
Advanced Network Emulators
Netropy
Netropy advanced network emulators simulate up to 15 separate WAN links, each with their own bandwidth, delay, and loss characteristics, through each pair of physical ports. Packets can be assigned to individual links by IP address range, VLAN, or any other packet specifier.
-
product
System Trace Emulators
XDS560v2
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
product
JTAG Boundary-Scan Packaged Solutions
Corelis offers an extensive line of boundary-scan software packages that can also be custom tailored to create the right package for any user. For datasheet information, please click here.
-
product
Mixed Signal JTAG Tester
JT 5705
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
product
JTAG Test Software
JTAG Technologies software has been subject to a program of continuous development for over 20 years. The first products, launched in 1991 formed the start of our 'Classic' range of software and featured the first automatic boundary-scan test program generator (ATPG) for PCB interconnects plus associated test execution and diagnostics software. In 2006 JTAG Technologies launched it's new flagship tools platform JTAG ProVision.
-
product
Emulation & Test Interface
Solder down modules to suit any package type provides a cost effective solution for replacement test heads, male or female. The mating top modules can incorporate either a ZIF or standard IC socket and the addition of optional test pins if required from RS Components.
-
product
JTAG Live Controller
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
product
Battery Emulator And Profiler
E36731A
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
product
Terminal Emulator
Distinct IntelliTerm
Distinct IntelliTerm is a terminal emulator that allows you to access data on diverse corporate information servers such as IBM mainframes, IBM AS400, UNIX and VAX systems from a single application. It includes full featured terminal emulation for TN3270E, TN3270 for Type 3278 and 3279, with support for 3179G, 3192G, 3472G and 3279 S3G graphics, TN5250 and VT52 through VT420. Distinct IntelliTerm operates over the Telnet protocol running over TCP/IP, an area in which Distinct is a market leader. Distinct IntelliTerm integrates related utilities such as multi-connect FTP with SOCKS proxy support, print server support with LPD and 3287 printing support, substantially reducing your training and support costs.
