Filter Results By:
Products
Applications
Manufacturers
Interrupters
-
product
Intel 80486 DX2 Processor Board
MS 1500
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
product
STD Bus Backplane
VECTOR Electronics and Technology, Inc.
Vectorbord® STD Bus industrial backplanes per IEEE 961 microcomputer bus, compact and rugged are fully assembled and tested. Designed for 4.5” X 6.5” plug-in boards, Vector STD Bus backplanes are available in 8 or 16-slots. Speed capability up to 10MHz; 2-layer design. Ample positions for decoupling capacitors; interrupt priority lines.
-
product
VME64x IP Carrier Module
DP-VME-5121
Data Patterns DP-VME-5121 VME IP carrier board is a 6U VME bus card that provides an electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.Each IP module supports two interrupt requests. The VME bus interrupt level is software programmable. The software configured interrupt modes are:a.Single level interrupt mode: All IP module interrupts can be mapped to a single VME bus interrupt level.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
783007-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
product
Auto Reclose and Sync Check
Operating records for overhead power lines reveal that most faults are of a transient nature (e.g. lightning induced) & that service interruptions may be minimized by use of automatic reclosing of circuit breakers. An automatic reclosure of the circuit breaker, after the fault clears, provides improved service continuity & system stability. The 1B230 Series Reclose Relay provides for single or double shot automatic reclosing of circuit breakers, following interruption of supply due to a fault in the system.
-
product
Circuit Breaker Analysis Systems
When a fault such as a short circuit or current overload is detected by a protective relay, a trip impulse is sent to the circuit breaker. The circuit breaker must function as specified and interrupt the current as soon as possible or severe damage may occur. The damage caused by a malfunctioning circuit breaker can often be catastrophic, resulting in significant damage to the electrical system.
-
product
PCIe Digital I/O Board, 32 Optically Isolated I/O Channels, 24V
APCIE-1532
16 digital inputs, 24 V, isolated16 interruptible inputs16 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
Optical Fiber Identifier
TW3306
Techwin(China) Industry Co., Ltd
Optical Fiber Identifier TW3306Ais an essential installation and maintenance instrument. By inserting the fiber into its adapter head, it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Windows
778032-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Socket Tester
1945
Peaceful Thriving Enterprise Co Ltd
This is a portable 220VAC socket tester to inspect the wiring conditions. The tester also features current variation for simulation of different leaking current. With the current variation, technician is able to test the condition of Ground Fault Circuit Interrupter (GFCI) / Residual Current Device (RCD) easily.
-
product
Current clamps
Precision ammeters determine the intensity of an electric circuit without interrupting the current flow.
-
product
Interface Board for Conduction Cooled PCI Mezzanine Card Systems
EXC-708ccPMC
The EXC-708ccPMC is an ARINC-708 /453 interface board for conduction cooled PCI Mezzanine Card systems. The board supports two or four ARINC-708 /453 channels. Each of the channels can be programmed either as transmit or receive. Each channel implements an 8K×16 FIFO and supports polling and / or interrupt driven operation.The EXC-708ccPMC comes complete with C-driver software library including the source code.
-
product
Voltage Dips and Interruptions Generator
CSS61000-11
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Programmable Delay Line Instrument
XS-100
The XS-100 is designed for those who need faster switching speeds and measurements without interruptions
-
product
IP Parallel HV
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
product
On-Line Electric Motor Analyzer
EMAX
We understand that shutting down electric motors for testing can be time consuming and costly. With the EMAX technology you can now test a motor while it is operating with no interruption to production. Within seconds the EMAX will provide a comprehensive detailed look at the Power Circuit, Power Quality, Stator, Rotor, and Air Gap.
-
product
Digital Indicator for Strain Gauge Sensors
AD-4530
Low cost digital indicator for various applications. Suitable for measurement of load, pressure, torque, tension and more at an affordable price.Digital Zero (DZ) stores zero data at any measurement point. This function can also be used to tare weight. Measurement can simply be restarted when it was interrupted by a loss of power.Power on zero function adjusts to zero when the power is turned on.Digital filter provides stable measurement results.Digital span calibration. Easy calibration just by inputting the rated output of a sensor. No need to use a mass.
-
product
Large Current Battery Short Circuit Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Large Current Battery Short Circuit Test DeviceApplication: Battery Module, Battery Pack, Battery System short circuit.Short Circuit Mode: Pneumatic drive contact + Vacuum Interrupter
-
product
10-CH General Purpose Timer/Counter & 8-CH DIO Module
cPCI-8554
- PICMG 2.0 Rev 3.0- Four 82C54 programmable timer/counter chips- Up to 12-CH 16-bit timer/counter- 1-CH 32-bit cascaded timer based on 8 MHz clock source- Four programmable clock sources for each timer/counter- Programmable de-bounce filters for external clock & external interrupt inputs- 8-CH TTL digital inputs & 8-CH TTL digital outputs- +12 V and +5 V power available on the connector
-
product
IEC61000-4-11 Voltage Dips And Interruptions Simulator Generator
VDS-1120DX
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
8 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-8-8
- 8 electromechanical relays with change-over contacts The PCI-Express 8 relay board APCIe-2200-8-8 has 8 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
product
Power Conditioning
Having a solid power conditioning solution in place before you experience a sag or interruption in power will help you maximize your overall system reliability. Measurlogic provides an array of voltage sag and interruption support solutions for proactive power quality issue prevention. Our DPI and VDC solutions help facilities mitigate future losses due to power quality issues, including lost production time, damaged products, and maintenance after a voltage disruption.
-
product
Damage Indication
FilterCHECK
Get the full picture immediately with FilterCHECK: accurate on-site damage indication — wherever you do maintenance.Equipment fluid filters have a story to tell. With FilterCHECK, filters reveal an accurate account of component wear and damage, plus a reliable prediction of the time remaining to component failure. Easy to use, field-deployable FilterCHECK automates filter debris analysis, so your team can manage maintenance decisions efficiently. Avoiding component failure, reducing maintenance costs and eliminating service interruptions: three reasons FilterCHECK belongs on the shop floor, wherever mission-critical equipment is serviced and maintained.
-
product
GPIB Instrument Control Device
GPIB Instrument Control Devices offer IEEE 488 controllers that are compatible with ExpressCard, PMC, PCMCIA, PCIe, PCI, and USB slots as well as Ethernet, RS485, RS422, and RS232 ports. Some models can control multiple GPIB devices, and others offer sustained data transfer rates and no microprocessor interruption in data transfers. GPIB Instrument Control Devices include a license for the NI-488.2 driver software, providing maximum reliability for connecting to third-party instruments via GPIB. The devices are completely IEEE 488.2 compatible, have industry-standard transfer rates, and offer easy system configuration through NI software.
-
product
PXIe-SMN Interface Card
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
product
Watchdog Timers
ST offers watchdog timers as standalone devices (separate from the microprocessor) for applications requiring a high security level. These devices are a robust, reliable means of monitoring software code execution, or hardware failures, and can trigger appropriate action, such as system reboot, high-level interrupt generation and others.
-
product
High Power Programmable AC Source with Transients
61510
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
