Filter Results By:
Products
Applications
Manufacturers
-
product
Thermocouples With Terminal Heads
Thermocouples with Terminal Heads including Mineral Insulated, Industrial Style & remote wall mounted housing thermocouples.
-
product
Probe Head
cViper
cViper™ is an ultra-fine pitch probe head for RF and high speed digital WLCSP. cViper is ideal for lab and large volume production test for precision analog, RF, sensors and mobility devices. Low loop inductance and high bandwidth up to 27 GHz, cViper offers low and stable contact resistance for singulated devices or wafer-level test. A variety of contact materials to optimize performance are available with device pitch down to 100 µm.
-
product
IQ4 Rectangular Search Head
The IQ4 Rectangular Search Head Metal Detector is designed to be integrated within production lines or conveyor systems.
-
product
Mass Burette Flow Detector
FX-1100 Series
The FX-1100 Series Mass Burette Flow Detector takes the position of the fluid surface inside the burette as the head pressure using the differential pressure detector attached at the bottom and directly measures the flow of fluid as a mass based on changes in this pressure. It does not require calculation correction of temperature and specific gravity, and has many advantages such as high accuracy and extremely less affected by air bubbles, which enable to measure fuel consumption in the tests such as chassis dynamometer and engine bench. The 3 models are available according to the measurement range and application.
-
product
Module Accessory Kit, Quantity 26, 4-40 x .625" Socket Head Cap Screws
510109302
Module Accessory Kit, Quantity 26, 4-40 x .625" Socket Head Cap Screws
-
product
Infrared Gas Detector
iTrans2
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
product
Industrial Gas Detector
OLCT 60
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
product
Area Monitors
Provides real-time remote radiological monitoring. Local readout of hand-held meter allows for use as a portable survey instrument. More importantly, since the probe’s sensitive electronics are located far from the high field (25 to 350 feet away), they are not subject to destructive gamma exposure. The probe head may be placed directly into a filter compartment or against a resin tank or waste liner.
-
product
Process Industry Head Thermometers
Rough environmental conditions, hazardous areas, space-saving installation and flexible assembly are only some examples of the skills of our daily proven and reliable temperature sensors. With direct sensor output or 4 to 20 mA HART, PROFIBUS, FOUNDATION Fieldbus or WirelessHART communication, including device configuration with LCD display. Available without thermowell or with welded or drilled thermowell for sensor protection. Available also for non-invasive temperature measurements with high precision.
-
product
Laser Head
5517EL
The Keysight 5517EL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Module Accessory Kit, Quantity 26 4-40 x .25" Flat Head Phillips Screws 100 Degree
510109367
Used with modules: 510108112.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Exciter Head
The Exciter Head, with its force and displacement transducers, generates and measures the force or torque to the structure being tested and provides feedback signals for control of the test variables.
-
product
Pulsed Lasers and LEDs
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
product
Full HD Surgical Monitor Series
ASM24FHB
The ASM24FHB Series of medically certified FHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
product
Optical Power Meter Heads
The 5mm detector area on Keysight's latest optical power heads allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
product
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
510109306
Module Accessory Kit, Quantity 26 2-56 x .375" Flat Head Slotted Screws
-
product
Photometers
S 1000
Universal high-precision instruments for the measurement of illuminance E with system photometer heads for laboratory applications in automated measuring systems with computer control.
-
product
M2 & BPP Systems
The M2 factor wil define the beam propagation characteristics compared to ideal Gaussian beam propagation. According to ISO Standard 11146 rightfully offers the laser beam characterization as "M2 times diffraction limited beam", as such, a perfect beam will have an M2 of 1. 1 will be the best achievable value and no beam could have an M2 less than 1. Our conceptual design is based on sub-assemblies allowing to change the sensing head in the M2 device, offering multiple wavelengths heads up to 2.7 microns from deep UV (knife-edge technology) and camera based technology with built-in automatic filter wheel for adjustment. For focused beams, the same measuring head could be attached to a device for meauring highly divergent or highly convergent beams - FocusGage-BA, wherein the Laser Analyzing Electronic Autocollimator offers the capability of divergence measurement with Coming Soon M2 definition. M2Beam is the cornerstone of those measuring devices.
-
product
Digital Tachometer
TAC-L
Model TAC-L Portable Digital Tachometer measures rotational speed either by contacting a rotatable head to the shaft of the object, or using photo sensor to detect the reflections from the laser. The laser target can record from a distance of up to 20 inches and gives a more accurate measurement than LED targeting. Model TAC-L includes a large LCD with a backlight for use in dark areas.
-
product
Industrial Inline Process Refractometer – 2″ Tri-Clamp Fitting
VIP2
The MISCO VIP2 (“Very Important Process”) inline process refractometer showcases the latest advancements in smart-sensor technology. Housing the intelligence for processing and communication in the sensor itself, the VIP2 refractometer eliminates the need for an external control box. The stainless steel sensor head and sapphire measuring surface are designed to survive the toughest environments. The sensor mounts to your processes using an industry standard 2” Tri-Clamp fitting.
-
product
Wireless Meters
Digital Multimeter is loaded with the parameters and ranges HVACR professionals need for HVACR troubleshooting, plus it receives measurements wirelessly from any of the Fieldpiece Accessory Heads when connected to the wireless transmitter that''s included. You can now easily measure current, resistance, voltage, capacitance, frequency, continuity, and temperature either directly, or wirelessly from up to 75'' away.
-
product
Ultra HD Surgical Monitor Series
ASM27UHB
The ASM27UHB Series of medically certified UHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
product
Universal Scanning Head
CF106
Calmet Smart Calibration Devices
Universal miniature scanning head for detecting (counting) impulses from inductive, LED and LCD energy meters. Additionally it enables counting of manually triggered impulses (Start/Stop push button function). Sometimes (when access is difficult) it is the only way to count pulses from inductive, LED and LCD meters.
-
product
Compact CO2 Laser Marker
LP-GS Series
Panasonic Industrial Devices Sales Company of America
The LP-GS Series is a compact CO2 Laser Marker capable of very fine markings.Features:- Compact Head And Controller- Very Fine Marking For Small Objects- 5-Watt CO2 Laser
-
product
Module Accessory Kit, Quantity 26 2-56 x .25" Flat Head Phillips Screws Stainless Steel
510109373
Used with modules: 510104249, 510104267 and 510104289.
-
product
Pressure Measurement
When operating below the Pirani gauge range (10-3 mbar), an ion gauge can be used to measure pressure. There are a range of gauge heads and filament materials to cover specific pressure ranges and vacuum requirements in this region. The VACGEN ion gauge heads operate using the same principle but vary in design and construction to most accurately monitor pressures within specific ranges.
-
product
Universal Preamplifier 14
UP14
For Two Dimensional Magnetic Recording (TDMR) and Heat-assisted Magnetic Recording (HAMR) Headamplifiers. Universal Preamplifier 14 (UP14) is designed for TDMR and HAMR Head Amplifiers. With new Guzik RWA4000 TDMR, UP14 allows to process signals from three Read Channels. It also supports two high speed data channels for Write data and Laser data. UP14 has two channels for dynamic TFC control and allows to program TFC power per sector and close loop TFC power control in each channel. UP14 can generate two programmable modulation signals for write data and laser data with bandwidth up to 20 MHz. UP14 consist of two boards. The first UP14 RW Board processes high-frequency signals: read-back signals, write data and laser data. The second UP14 Control Board provides power, control and low-frequency signal generation: TFC, write data modulation and laser modulation.
-
product
Frequency Extension Heads for Vector Network Analyzers
FEV
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
