Filter Results By:
Products
Applications
Manufacturers
-
product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-02
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
product
PEM Fuel Cell Test Stations
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
product
sbRIO-9225, Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780588-01
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
-
product
NI-9225, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module
780159-01
300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The NI‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three NI‑9225 channels.
-
product
NI-9206, ±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module
779526-01
±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module - The NI‑9206 performs differential analog input with four programmable input ranges. The module provides up to 600 VDC (400 VDC in Europe) channel‑to‑earth ground isolation, making the module ideal for accurately monitoring large fuel cell and battery stacks. By referencing the module common (COM) to the middle of the NI‑9206 bank, you can measure 16 consecutive cells and remain within 10 V of the module COM.
-
product
PXI-2584 , 12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module
778572-84
12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module —The PXI‑2584 is a high‐voltage PXI multiplexer switch module that is ideal for fuel cell and battery stack applications. The reed relays in the PXI‑2584 ensure longer lifetimes and faster actuation times for test equipment. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Fuel Cell Hardware
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
product
Fuel Cell Test Systems
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
product
Fuel Cell Test Accessories
Scribner extends its groundbreaking line of tabletop fuel cell testing equipment with the 885 Fuel Cell Potentiostat.
-
product
Fuel Cell Test Systems
Fuel Cell Test System is a complete test station for operation and measurement of PEM/DMFC fuel cells.
-
-
product
BACnet Stack
softBAC
Softdel’s softBAC is an intelligent version of the industry-standard BACnet protocol stack for Building Automation and Control (BAC) networks. The softBAC stack is fully PR19 compliant and is available as per standard BACnet profile packages such as:
-
product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
-
product
HART Protocol Stack
softHART
SoftHART is the industry-standard smart HART (Highway Addressable Remote Transducer Protocol) communications stack for industrial automation. HART is a bidirectional protocol and communicates over existing 4-20 mA analog current loops, extending communication capabilities without the inconvenience of installing additional wiring.
-
product
Stack Probing Sensor
L722
The Model L722 Stack Probing Sensor coupled with the L612 Digital Recording Moisture Meter makes it easy to reach deep into stickered units of lumber and take accurate moisture readings without the danger of broken pins. Wagner''s electromagnetic wave technology makes it possible to take multiple readings throughout an entire stack in just minutes.
-
product
Fuel Pressure Testers
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
Battery Fuel Gauge
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
product
Fuel Cell Test Station
E1PS is glad to bring you a low cost method to test fuel cells and produce professional test data results for under $1,000.00, fuel cell included! The Fuel Cell Test Station comes complete with everything but the hydrogen. There are three meters*, a load box, forced air housing and a fuel cell.
-
product
Fuel Injection Tester
FIT13A
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifold. Includes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446); Japanese fuel injection systems; a The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
product
Fuel Moisture and Fuel Temperature Sensors
Fuel moisture and fuel temperature sensors emulate and measure the moisture content and temperature of similarly sized twigs on the forest floor. The sensors are typically used as part of larger systems, such as fire weather stations with dataloggers and telemetry capability, to remotely assess changing fuel conditions and potential fire hazards.
-
product
Fuel Density Meter
FD-5110
By connecting with the FM-3100 Digital Flow Meter, the FD-5110 Fuel Density Meter can measure temperature and density data in real time. In addition, the FP series Volumetric Flow Detectors with wide range ability and the FD-5110 are the best choice for achieving the accurate mass flow measurement.
-
product
GTEM cells
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
product
Fuel Injection Pressure Tester
33900
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
product
CELL TESTER
SPOTLIGHT
SpotLIGHT was designed to minimize maintenance and to significantly reduce downtime. The lifecycle of its contacting system is longer than that of standard systems currently available on the market, thus substantially reducing TCO.
-
-
product
Load Cells
Honeywell Industrial Automation
Honeywell Sensotec manufactures a wide range of tension, compression, and universal measurement load cells. These load cells are manufactured as standard, modified standard, and custom sensors to provide fast delivery. Many units can ship from our extensive stocking program within 24 hours.
-
product
FUEL INJECTOR CANISTER CLEANER
FIT470B
*Cleans carbon from intake valves, fuel passages and cylinders with a professional carbon cleaning solution*Will restore the original spray pattern more effectively, giving improved performance, fuel economy and emission tests*Uses shop air with any professional canister cleaning solution on the market
-
product
Fuel Cells Testing
A fuel cell is a critical device that can convert the chemical energy in liquid fuels into electrical energy. It is widely used in various industrial applications for power generation and transportation. The development and installation of fuel cells for use in portable and stationary applications is expected to help solve worldwide fuel-energy problems.
