Filter Results By:
Products
Applications
Manufacturers
Frequency Response Analyzers
Analyze a circuit's or system's response to different frequencies. AKA: FRA
See Also: Impedance Analyzers, FRA, Potentiostats
-
product
Sweep Frequency Response Analyzer
FRANEO 800
FRANEO 800 was developed for testing the mechanical and electrical integrity of power transformers after transportation or exposure to high fault currents. It uses the sweep frequency response analysis (SFRA) principle and measures the electrical transfer function over a wide range of frequencies.
-
product
Signal Injectors
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Potentiostat Galvanostat
VersaSTAT 4
The improved low current performance with fA resolution and pA accuracy addresses current sensitive applications such as sensors, corrosion, inhibitors, and combined with the optional FRA, coating technologies. The additional analog filtering makes the VersaSTAT 4 an even better choice for low-current applications while the additional bandwidth filtering adds extra stability for capacitive cells. The VersaSTAT 4, with its additional capabilities, makes an exciting addition to our VersaSTAT family making them even more of an exceptional value for all of your application needs.
-
product
High Resolution Frequency Response Analysis (FRA) System
TR-AS FRA
The Frequency Response Analysis (FRA) on power transformers is used for diagnosis at works, after putting into operation and for maintenance on site. The frequency dependent admittance is determined and recorded as fingerprint.
-
product
Digital/Analog Frequency Response Analyzer
8800 Series
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Time Domain Analysis
S97010B
The S97010B time domain analysis capability allows you to measure the time domain response of a device. The analyzer can transform frequency domain data to the time domain or time domain data to the frequency domain.
-
product
Oscilloscope Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Oscilloscope for transient vibration signals*Displays the time response of vibration acceleration and VM-SCOPE+ also for velocity and displacement*Suitable for shock and drop testing of packagings and other products *Memory for 110 s post-trigger and 1 s pre-trigger real time signal recording*Two measuring cursors*Export function for bitmap and text*Up to four signals per window*One VM-SCOPE license can be operated simultaneously up to four times with different settings *Measurement of decay time*Measurement of HIC (Head Injury Criterion)*VM-SCOPE may trigger the frequency analyzer module VM-FFT*External Messengers *Offline measurement
-
product
Field Analyzers
Active broadband isotropic antenna combined with portable USB powered spectrum analyzer. OFA-S/SE antenna has frequency response independent of antenna or electric field orientation. It offers broad dynamic range for the variety of RF regulatory, safety, EMC, wireless and telecommunications applications. Spectrum analyzer SA-S displays the frequencies and field strength of selected signals, allowing all results to be viewed and stored on PC.
-
product
Solar Test Systems
AMETEK Scientific Instruments manufactures a range of application specific XM (Xtreme Measurement) products focused on solar cell / photovoltaic research (developed in collaboration with Professor Laurie Peter of the University of Bath, UK). These products are so versatile that they can also be used for photoelectrochemical (PEC) water splitting applications; and make use of Solartron’s unique high performance XM specified potentiostats and frequency response analyzers to provide a full complement of techniques for research into energy, corrosion and analytical electrochemistry.
-
product
Sweep Frequency Response Analyzer（FRA Test Set）
HTBX-H / 210
Wuhan Huatian Electric Power Automation Co., Ltd.
Internal structure fault detection of power transformers essential tools.
-
product
Injection Transformer
J2100A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
3671 Series Vector Network Analyzer (100kHz - max.43.5GHz)
3671
3671 series network analyzer provides frequency response, single-port, response isolation, enhanced response, full-dual port, electronic calibration etc. Offer various display formats, such as logarithmic amplitude, linear amplitude, phase, group delay, Smith chart and polar coordinates. 3671 series can accurately measure the amplitude frequency characteristics and phase frequency characteristics and group delay characteristics of microwave network.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
Spectrum Analyzer
WaVue™
RF Spectrum Analyzer is an invaluable tool for the test, design and maintenance of radio frequency signals, circuitry and equipment.Engineers have been widely using spectrum analyzers to measure frequency response, noise, and distortion characteristics of all kind of radio frequency circuitry. Also in EMC testing, wireless spectrum analyzer is used for basic pre-compliance testing.
-
product
EIS Interface (Electrochemical Impedance Spectroscopy)
BATT470m
The BATT470m electrochemical impedance analysis interface (EIS) provides an easy to use battery/cell impedance test platform for the electrochemical industry. Utilizing the highly accurate PSM3750 frequency response analyzer from N4L, the BATT470 provides impedance measurement of batteries/cells up to 100V DC. With a frequency range of 100mHz to 1MHz, the BATT470m covers a wide range of applications. Our software package - PSMComm2, featuring “EIS” mode, displays the in-phase and quadrature impedance of the cell in Nyquist form as well as overall impedance (Z), in bode form.
-
product
Vector Network Analyzer
SNA5000A
The SIGLENT SNA5000A series of Vector Network Analyzers have a frequency range of 9 kHz to 8.5 GHz, with 2 and 4 port models available. Designed to give you instant insight into scattering, differential, and time-domain measurements. They are effective instrumentation for determining the Q-factor, bandwidth, and insertion loss filters and feature impedance conversion, movement of measurement plane, limit testing, ripple test, fixture simulation, and adapter removal/insertion adjustments. There are five sweep types: Linear-Frequency, Log-Frequency, Power-Sweep, CW-Time, and Segment-Sweep mode. The SNA5000A series VNAs also support scattering-parameter correction of SOLT, SOLR, TRL, Response, and Enhanced Response for increased flexibility in R&D and manufacturing applications.
-
product
Frequency Response Analyzers
Frequency Response Analysis (also referred to as Transfer Function Analysis) measures the output spectrum of a system relative to a stimulus, and is used to characterize the dynamics of the system under test. The technique measures the magnitude and phase relationship between output and input waveforms as a function of frequency. The input signals may be from a wide range of sensors including acoustic (microphones/sonar), mechanical (accelerometers/displacement transducers), optical (photodetectors), and electrical (amplifiers).
-
product
Parallel systems
Did you know you can couple several Gill AC, Gill 12 and Weld Testers together or any combination of Gill AC, Gill 12 or Weld Tester, to give you a parallel logging multiple Potentiostat / Galvanostat / ZRA / FRA system, capable of recording from each working electrode at up to 60 readings per second. Coupling several Gill ACs or Gill 12s together gives the added abilities of the Weld tester and the ability to perform fast sweeps. Using our latest software, it has never been easier to couple instruments together to provide a Parallel System. In fact up to 32 instruments can be controlled at the same time. These instruments can either have individually enclosures or be rack mounted.
-
product
Frequency Response Analyzers
6300 Series
The Venable Model 6300 Series is our popular 2-channel hardware/software system supplying the same functionality as all Venable FRAs, with the 6300 leading the industry with more integrated testing and measurement capabilities than any other instrument in its class.
-
product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
product
Frequency Response Analyzers
7400 Series
The Venable Model 7400 Series is the top of the line in Venable performance, supplying 4 channels for increased testing, measurement and analysis functionality. Originally designed for measuring 3-phase impedance and source and load simultaneously, the Model 7400 is a robust solution for organizations requiring high availability for high volume and/or simultaneous testing.
-
product
Vector Network Analyzers for LMR
Vector network analyzers are a valuable tool for radio technicians. VNAs allow you to tune frequency dependent components including transmitters, combiners and isolators, circulators, duplexers and filters. With a VNA you can measure and adjust S11 parameters, measure return loss, or analyze and fix response issues. CMT offers compact VNAs ideal for benchtop and field use.
-
product
Frequency Response Function
FRF
FFT Spectral Analysis. Frequency Response Function (FRF) is a commonly used measurement type of the Dynamic Signal Analyzer. FRF is defined as the ratio of response i.e. acceleration, velocity, or displacement with respect to the excitation force which is the reference.
-
product
Impedance Analyzer
1260A
The model 1260A Impedance/Gain-Phase Analyzer is - without doubt - the most powerful, accurate and flexible Frequency Response Analyzer available today. In daily use by leading researchers wherever measurement integrity and experimental reliability are of paramount importance, the 1260A’s solid reputation is frequently endorsed in published research papers in fields.
-
product
Software - for controlling Cleverscope
Cleverscope Windows Application Software. Note we have added the Frequency Response Analyser (FRA) and Streaming capability to our Cleverscope application and so now it is available with all variants of our products, including units you have already bought. For power supply and power plane measurements you do need the isolated CS701 signal generator.We also now have the CS448 with four 1kV isolated channels with CMRR > 100 dB at 50 MHz.
-
product
Vector Network Analyzers
A vector network analyzer is an instrument that measures the frequency response of a component or a network composed of many components, which can be both passive and active.
-
product
Frequency Response Analyzers
The PSM range of instrumentation provide not just conventional frequency response measurements but can also be combined with an Impedance Analysis Interface to form a high accuracy impedance analyser, in the case of the PSM3750 this solution is able to provide impedance analysis up to 50MHz
-
product
Discrete Input Event Recorder
Wabtec M Series Recorders provide a compact recording solution for discrete electrical and pneumatic signals and provide compliance to FRA Crash Hardening requirements.
