Filter Results By:
Products
Applications
Manufacturers
-
product
Handheld Grounding Tester
HGT1
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
Compact OTDR
◇ 5.6-Inch outdoor-enhanced touchscreen, 7.4V/4.4Ah Lithium battery◇ Event Dead zone as lower as 1.5meter◇ Combined multi-dynamic range and wavelengths◇ Muti measurement mode, support Touching LCD and pressing keys◇ Warning function could prevent OTDR module from being damaged by optical signal in fiber.◇ Realtime measuring function, convenient to monitor the splicing process◇ Integrated 10mw Visual Fault Locator◇ Support English/ Chinese input, adopts friendly input interface, totally simulate the computer keyboard input ◇ Integrated with 8GB internal memory, more than 80,000 groups curve storage◇ PC remote access and control function is available, which support the printing work of the measurement report
-
product
Fault Locators
For the first time, you can detect the type of fault and locate the position of an electrical fault that causes intermittent or persistent circuit breaker trips, thus giving you the critical information needed to reduce call backs for circuit breaker trips.
-
product
PXI BRIC8 FIBO Matrix Dual 20x4 3pin brkout
40-592A-101
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
Hipot Tester
HVA Series
HVA systems detect faults in cable networks in a non-destructive yet efficient way and fulfill all the requirements of modern cable testing.
-
product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
product
Ground Fault Monitor
IFT-120
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
product
PXI Solid State MUX, 4 bank, 40 channel
40-680-004
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
product
BSD (Test Diagnostics)
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
product
635nm Visible Light Source
VLS-40
The KD Optics VLS-40 is an easy to use, hand-held, visible source used for testing fibre optic cable installations. It is especially useful when testing fibre optic cables close to the terminal equipment. The unit is pocket sized with a long battery life, making it ideal for local fault finding and continuity checking of fibres.
-
product
Ground Fault Locator
K-3837
Kongter Test & Measurement Co., Limited
Kongter’s K-3837 Ground Fault Locator is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems with earth fault. It will save you from long time unnecessary troubleshooting and helps to increase the stability of your electrical equipments. It is widely used in various DC systems including power utilities, locomotive, telecom and etc.
-
product
Communications System Analyzer
Freedom R8200
The Freedom R8200 from Astronics Test Systems represents a major step in the evolution of the Land Mobile Radio Test. The Freedom R8200 is the first and only test instrument that combines comprehensive digital and analog LMR testing with the ability to measure important RF network characteristics, such as Distance to Fault (DTF), Return Loss, and Voltage Standing Wave Ratio (VSWR). The Freedom R8200 is also the only service monitor with the abilityto display advanced RF Parameters in a Smith Chart for more complicated network analysis
-
product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-012
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
LOADpro Dynamic Test Leads
180
*LOADpro Test Leads load the circuit to see if current can flow. *By loading the circuit, LOADpro makes a voltage drop test “on the fly”. *Just press the switch – the test results can not lie. *Use LOADpro w/your DMM and follow our test method - you will find wiring faults quicker. *LOADpro Test Leads feature SteadyPin Probe Tips, which allows the probe to sit firmly on a male ECM or connector pin. *LOADpro are OEM approved – finds corroded circuits fast!
-
product
4 Station Endurance Test Setup for Thermostat of Iron
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
product
RS-485/RS-422 Fault Protected
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
product
Polyphase Socket Tester
K-281
Knopp’s K-281 Polyphase Socket Tester is designed to detect backfeed conditions, grounds, short circuits and wiring errors in either a 120/240, 120/208 or 277/480 volt meter socket. It is equipped with high intensity Power Lights and Fault Lights to show whether or not the meter is safe to set. The Polyphase Socket Tester also comes with a heavy duty handle for quick and easy installation.
-
product
Sensor Imitator Probe
The Sensor Imitator Probe is mainly used for the simulation of the signals generated by different types of sensors in the vehicle. It can be used in all automobiles (12V/24V), to distinguish faults that lie in the sensor itself or are related to the connectors or wires.
-
product
PXI Dual Bus 64-Chan 2A Fault Insertion Switch
40-190B-102
The Dual Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Encoder Testing
HEIDENHAIN offers testing and inspection devices for the adjustment and fault diagnosis of its encoders. The highly accurate inspection devices are universally deployable, capable of being calibrated and interposed within the closed control loop. The testing devices are primarily used for the functional testing and adjustment of encoders. HEIDENHAIN encoders deliver all of the setup, monitoring, and diagnostic data needed.
-
product
Touch Screen 1550nm Single Mode Mini OTDR
TR1500S
Shenzhen Sharingtek Communication Co., LTD
The TR1500S mini OTDR is compact and easy to carry. It adopts a 3.5 inches high-definition touch screen, supports multi-touch and smooth operation, integrates OTDR, event map, optical power meter, light source, visual fault locator and flashlight in one unit, to meet various test needs in different occasions. The OTDR function adopts 1550nm wavelength and is built in high-efficiency wavelength isolator. It can perform optical live test on 1490 and 1577nm optical links, which supports up to about ±10dB optical live test. Its maximum measurement range is 80km.The TR1500S is used to measure optical fiber’s length, loss, connection quality and other parameters. It can easily test the breaking point, bend and loss point of the optical fiber links. It is suitable for maintenance personnel to have optical line maintenance and emergency repair testing.
-
product
Thermal Imaging Camera
Zhejiang ULIRvisionTechnology Co., LTD
A thermal imaging camera is a device that uses infrared and thermal imaging technology to convert the image of the temperature distribution of the target object into a visible image through detecting the infrared radiation of the target object and applying signal processing and photoelectric conversion. The thermal imaging camera accurately quantifies the actual detected heat and images of the entire object in real-time in the form of a surface, thus accurately identifying the suspected fault area that is heating. The operator initially judges the fever condition and the fault location through the image color and hotspot tracking display function displayed on the screen of the thermal imaging detector, and strictly analyzes it, thereby embodying high efficiency and high accuracy in confirming the problem.
-
product
Electrical Safety Test Equipment
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
product
Power Divider, DC to 50 GHz
11636C
The Keysight 11636C is a DC to 50 GHz power divider that provides highly accurate direct power dividing and combining. Excellent phase and amplitude tracking ensure accurate impedance matching of all three ports, which improves the fault location measurement by reducing re-reflections and intermodulation distortion.
-
product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-194A-002-HI
The 40-194A-002 is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
Pre- Locator
CFL PL2+
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCIe-7256
ADLINK's PCIe-7256 features all Form C type relays, ideal for device connection with on/off control. With latching relays, the PCIe-7256 further provides operating power conservation, while the status of each latching relay output is indicated by onboard LED. When the relay is in SET, its corresponding LED lights. Latching relays also feature unchanged status even when the system powered off, making the PCIe-7256 suitable for critical applications requiring output status to be maintained even under fault conditions. All digital input channels are non-polar and optically isolated, and may be set for optional use of RC filter. The PCIe-7256 also features a change-of-state (COS) function generating interrupt when any digital input changes state.
