Filter Results By:
Products
Applications
Manufacturers
-
product
Evaluation Kit
ROM-3310 Development Kit
*Evaluation kit for ROM-3310*Lower power TI sitara AM3352 1GHz processor*On board DDR3 512MB memory / 4GB Flash*HW WDT for system protection*Supports 1 GbE, 1 USB 2.0, 1 USB 2.0 OTG, 2 CANbus, 10 GPIO, 4 UART,1 I2C, 1 I2S, 1 SPI, 1 SDIO*Cable pack & Panel included*Evaluative image & test utilities built-in
-
product
Carrier Boards
ROM-DB7502
ROM-DB7502 is the Referenced Carrier Board designed for Advantech's Qseven 2.0/2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7502 design.
-
product
COM Express Type 6 Basic Module With Intel® Xeon® E3/7th Gen Intel® Core™ I7/i5/i3 Processors And Intel® CM238/QM175/HM175
CEM510
The CEM510 is based on the Intel® Xeon® E3 and 7th generation Intel® Core™ i7/i5/i3 processors with Intel® CM238/QM175/HM175 chipset. The 125 x 95 mm system-on-module was designed for graphics-intensive applications over the Industrial IoT, including industrial control, medical imaging, digital signage, and gaming machines. The embedded module is equipped with dual 260-pin DDR4-2133 SO-DIMM slots with up to 32GB system memory. Its wide operating temperature range of -40°C to +85°C strengthens the adaptability of various harsh conditions. For evaluation and development purposes, Axiomtek also has the CEB94011, a carrier board designed to operate with the CEM510 for additional I/O and expansions interfaces. Integrated with Intel® Gen 9 graphics, and with the support of DX12.0, OCL 2.0 and OGL 4.3, the module presents excellent graphics performance with resolution up to 4K (3840 x 2160 @ 30 Hz). Three independent displays are supported through LVDS and three DDI ports supporting HDMI, DisplayPort, and DVI (one DDI supporting optional VGA).
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
Universal Development Board For The Plug-in Module PCAN-MicroMod FD
PCAN MicroMod FD Evaluation Board
The PCAN-MicroMod FD Evaluation Board is a development board for the PCAN-MicroMod FD and enables the design and development of your own circuits with CAN connection and I/O functionality. It can also be used for training purposes for CAN and CAN FD structures. The user can access the resources of the attached PCAN-MicroMod FD via taps, screw terminals, switches and potentiometers and test configurations or test circuits.
-
product
Analog
Create complete systems while streamlining your development process and reducing your design risk. We design our mixed-signal, linear, interface and power products for seamless integration with our extensive portfolio of microcontrollers, digital signal controllers, microprocessors and FPGAs. Well-known for our thorough documentation, we provide parts that work on the bench the same way they’re described on paper. We also provide evaluation boards to demonstrate functionality, an intuitive Integrated Development Environment (IDE), simulation software and other design resources to create a rapid design, prototype and test environment for all aspects of your system design.
-
product
LSM6DSL Click
64207
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
Carrier Boards
ROM-DB5901
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
product
MPU 9DOF Click
64219
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
MI/O Extension Modules and Evaluation Boards
Advantech‘s MI/O extension modules and evaluation boards are designed for MIOe embedded single board computers (SBC) to extend functions such as USB 2.0/USB 3.0,and provide additional I/O interfaces via a high-speed connector.
-
product
Development Kits
Advantech development kits includes a series of carrier boards and starter kits with schematic software and reference design to accelerate evaluation.
-
product
RISC-V Processor IP Core Evaluation Kit
The EMSA5 demo platform is an ideal tool for evaluating the RISC-V processor IP core EMSA5. It contains an Artix®-7 35T FPGA Arty evaluation board with implemented EMSA5-IP core. Thanks to the included peripherals and expansion interfaces, the kit is ideal for numerous applications. The kit is JTAG programmable and includes Quad SPI Flash, a JTAG port, 10/100 Mb/s Ethernet and a USB-UART bridge, four Pmod connectors and an Arduino Shield expansion connector.
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
FMC Wideband RF Transceiver AD9371 Based
FMC-ZU1RF-A
Sundance Multiprocessor Technology Ltd.
The FMC-ZU1RF-A is a FMC for RF wireless communications applications based on the AD9371 component from Analog Device Inc (ADI).http://www.sundance.technology/wp-content/uploads/2018/01/FMC-ZU1RF-High-Res-Cutout-e1516095831285.jpgThis FMC is fully hardware and software compatible with the ADRV9371 evaluation board from ADI.
-
product
Camera Modules
e-con Systems Camera Modules come with parallel & MIPI interfaces. Our CMOS camera modules will be effective in any application or environment because of their versatility and wide range of options. Embedded camera module can be interfaced to processors like Tegra K1, i.MX6, DM3730, OMAP. Further to these HD camera modules, e-con offers evaluation boards with these camera modules interfaced to various development boards featuring these processors. We provide Omnivision Camera Module & Aptina Camera Module (ON Semiconductor) with CMOS Sensors.
-
product
Dynamic Data Simulator
LS-70-S
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
product
Evaluation boards
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
product
4K Picture Quality Analyzer
VP4000
The The frame delay of 2160p full sample 4K reference video and 4K test video are compensated to fit exactly to each other by pixel base, and a real time objective quality score (DSCQS) are calculated by the ITU-T J.144-based assessing method in conjunction with the differential values (PSNR). This scheme is best suited to the encoder evaluation, online/standby comparison, inspection geared to video servers, and so on. For conventional 1080i image evaluation, a single PROBE4000 board can serve the purpose.
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
FRAMOS SLVS-EC RX IP CORE
Sony’s SLVS-EC interface standard has emerged as the best high speed interface to Sony’s best image sensors, enabling higher throughput, greater signal integrity, and simpler designs. Engineers developing solutions using Xilinx FPGAs and SoCs can take advantage of FRAMOS’s SLVS-EC RX IP Core, Evaluation Board and tested source code examples. Device builders and camera vendors can de-risk the design while reaping the benefits of Sony’s latest high-speed interface.
-
product
Carrier Boards
ROM-DB7503
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
product
PCI Evaluation Board
BCM91125E
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
product
PCI Evaluation Board
BCM91250E
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
product
SMARC
SMARC (Smart Mobility Architecture) modules are ultra-small system-on-modules targeted towards applications that demands compactness and energy-efficiency. The SMARC system-on-modules also support Axiomtek evaluation carrier boards for easy integration and hardware design reference.
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
product
VME & VPX Evaluation & Development
EZ Platforms
Kontron provides a solution for a quick entry into the evaluation and development of VME and VPX applications. EZ turnkey platforms are compact air-cooled rack systems with pre-integrated VME or VPX board along with the associated rear transition module (RTM) and pre-loaded software. Engineers with no prior VME or VPX expertise can start application development in seconds.
-
product
Carrier Boards
ROM-DB3900
ROM-DB3900 is an evaluation carrier board designed for the Advantech RTX2.0 module. It is compatible with the RTX2.0 module ROM-3420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperature, and also supports two MIPI connectors for a camera module. ROM-DB3900 is an ideal development board for ruggedized applications, such as industrial control, automation control and HDMI systems.
