Filter Results By:
Products
Applications
Manufacturers
EDGE
Wireless service using TDMA, based on GSM standard operating at 384Kbps on broadband.
-
product
Edge Radius Measurement
EDGEINSPECT
NOVACAMTM EDGEINSPECTTM system is a modular, non-contact 3D metrology system that:Measures, down to the micron, any type of edge: cutting edges, inside or outside edges, edges on round holes, straight edges, etc.
-
product
Intel® Smart Display Module Small (Intel® SDM-S) With Intel® Pentium® Processor N4200 & Celeron® Processor N3350
SDM300S
The SDM300S is a signage computer module following the newest Intel® Smart Display Module Small (Intel® SDM-S) architecture. The SDM300S is powered by the onboard Intel® Pentium® processor N4200 and Celeron® processor N3350 (code name: Apollo Lake) with the Intel® HD Graphics 505 or 500 chipset. The sleekest all-in-one display module measures only 100 x 60mm (roughly the size of a credit card), which makes for a thinner display. The SDM300S can be easily connected to an SDM-compliant display via a high-speed PCIe edge connector - which supports 4K resolution displays and video capture and has built-in USB 3.0, HDMI 1.4, DisplayPort 1.2, Serial TX/RX and I2C signals. Nearly a third the size of Open Pluggable Specification (OPS), the design of the SDM300S omits housing so it is well suited for space-constricting applications.
-
product
IPTV Monitoring and Test Solutions
Net-x TVMS
The NET-xTVMS is a system of specialized computer probes networked to the enterprise server and clients. The probes, strategically located at the hub sites next to edge routers and edge QAMs, continuously monitor IPTV QoS with MPEG-TS transport metrics of SPTS and MPTS multicast streams as well as DVB-C MPTS streams. The NET-xTVMS is scalable from 1 to 1000 probes. Several types of probes are available to suit many different monitoring applications. Metrics are collected at the probes and alarms are sent to the server once they exceed predefined thresholds. A system wide alarm matrix, alarm logs and periodic metrics for each location can then be viewed via Internet on client computers.
-
product
OSM Size-L Module With NXP® I.MX8M Plus Series
OSM-IMX8MP
The OSM-IMX8MP is an OSM R1.1 Size-L module featuring NXP® i.MX 8M Pluss series processor with 4-core Arm Cortex-A53 and M7, up to 8GB LPDDR4L memory and up to 128GB eMMC storage. With its in-SoC 2.3 TOPS NPU and Vivante GC7000UL graphics, the module is made for edge solutions needing on-device AI processing at ultra-low power.
-
product
Professional Geological Compass
COCLA
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*Declination (± 30°) and inclination adjustable*Automatic arresting of needle when not in use*Eddy current damping allows reading after approx. 3 sec.*Transparent circle with diameter 50mm with interval of graduation 1°*Dip measurement range 270° graduated in 5°Reading by estimation 1°*Deep etched tracing edge graduated (60mm)*Circular spirit level (observable also from underneath)
-
product
Edge Compute Solutions
Innovate in real time. With the world’s largest serverless compute platform, Akamai puts your code closer to your users.
-
product
8 Connector-Hole Back Extension
9401-BE
Semi-enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 8 50/37 pin d-sub connectors. Space is provided to mount the standard DG-style 100 pin edge connector paddles.
-
product
Software
Part Tracking
Part Tracking technology is a software application included in Akrometrix Surface Measurement that increases system throughput while reducing user to user and system to system measurement variation. Part Tracking uses edge recognition technology to locate a part in space and automatically crop/rotate the sample for processing of the found surface area.
-
product
Hard Metric Eurocard Plugbord
8028
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 2mm Hard Metric connector. Pad per hole both sides. Combination Pattern: 0.100", 0.050" and 2mm grid.Pad and bus surfaces solder coated.Accepts cPCI 2mm J1 (25 row) & J2 (22 row) connectors on edge.
-
product
Plugbord
3677
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers. 3-Hole solder pads (0.28” x 0.080”) and buses forinterconnecting multiple component leads. No pattern on reverse side, edge contacts only Row and column legends provided.
-
product
Atomic Spectroscopy
Agilent’s comprehensive atomic spectroscopy software portfolio leads the industry in the simple setup and productivity tools required by routine analytical laboratories, while also providing the flexibility needed for advanced method development in research and academia. Our advanced ICP-MS software, including the powerful ChemStation and MassHunter systems, are used in all of our mass-spec platforms, so you can benefit from a single solution and reduce staff training requirements. Our cutting edge ICP software also enables intuitive control in ICP-MS processes.
-
product
CompactPCI
6U PMC Carrier
This conduction cooled 6U CompactPCI dual slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens the carrier and PMC module enabling the board to resist high shock and vibration.
-
product
Portable Protection Test Set and Calibrator
CMC 430
The CMC 430 is the preferred choice for test engineers in cases where excellent transportability is needed and three currents up to 12.5 A or six voltage outputs are sufficient. Its low weight of just 8.7 kg / 19.2 lbs, and robust design with its edge protection predisposes the device to every outdoor and indoor use.
-
product
Heavy-load Pallet Drop Tester KD-500
KD-500
King Design Industrial Co., Ltd.
*To evaluate impact effects of shock, drop and tumble encountered in repair and handling process, so do the safety strength assessment. *The general drop test is against bottom, angle, edge and tumble. According to related specifications you can lift one side of the product by angle to make it drop freely.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Digital Multimeter
8808A
The Fluke 8808A 5.5 digit multimeter dependably performs the most common measurements required by today’s applications. Whether you are performing functional tests or making critical measurements on test points, using the limit compare mode with pass/fail indicators eliminates production mistakes, especially those where results are “on the edge.
-
product
STD Bus, Vectorbord Plugbord
4610-1
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Voltmeter
DC Moving Coil
*Compact in size (build in depth 33mm).*Rugged movement ensures sustained accuracy and reliability.*Square bezel permits edge to edge mounting, allowing maximum use of panel space.*Clear scaling for easy reading.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781260-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A
eBOX671-521-FL
The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.
-
product
Digital Management Software
EdgeGO
EdgeGO® is a robust software platform for remote device management in edge computing environments. It prioritizes quick deployment and user-friendly operation while ensuring scalability and security.
-
product
Laser Tracker Tooling & Accessories
MetrologyWorks provides a full line of Laser Tracker Accessories as well as Laser Tracker Tooling and Adapters.This includes Drift Nests, Permanent Monuments, Pin Nests, Edge Nests, Hidden Point Bars.If you need something custom we can provide custom Laser Tracker Tooling as well.Bullseye Laser Tracker Tooling is compatible with all OEM Laser Trackers.BullseyeTM Series Tooling – “Never Miss your Mark”TMWe Currently offer 3 Sizes of Laser Tracker Tooling that are compatible with all SMR's
-
product
Digital Delay Pulse Generator
9420 Series
The Model 9420 Series Digital Delay-Pulse Generator with 2, 4 or 8 independent outputs is designed to provide cutting edge, yet cost-effective solutions to generate and synchronize multiple pulses for a wide range of applications. The delay and pulse width for each channel are independent and digitally controlled which makes the instrument ideal for situations that require synchronizing a number of different events. Channels: 2, 4, or 8 Independent Channel Outputs. Resolution: 10ns. Accuracy: 1ns + .0001 x period.
-
product
Plugbord
3682-4
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. Interleaved buses pattern on wiring side, solder coated for user convenience. Overall ground plane with clearance around each hole on component side. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board. Row and column legends provided.
-
product
Edge AI System
Axiomtek designs, develops and manufactures edge AI (Artificial Intelligence) systems to fulfill AI solution-ready system requirements. The AI embedded systems are ideal for smart manufacturing, machine vision, deep learning, edge computing, and much more.
-
product
Beam Profiling
The beam propagation factor M2 is a common single parameter that charac-terizes the whole beam as it propagates through space. According to ISO standard 11146, this parameter could be defined by several measurement techniques based on beam profiling along several points of the propagating beam. The standard defines several measurement techniques, all of which are based on beam profiling measurements using devices such as cam-eras, knife edge and slits. There are two main measurement requierments - 1) Measurements of focused beams. 2) Measurements of collimated beams. Our M2 devices are capable of measurements of both laser types and due to their modular design interchangeable heads can be mounted in same M2 gear.
-
product
Inductor Coils
SemiGen's Inductor Coils are manufactured using our thin film process on quartz substrates. The precision photolithography and non-chemical etching process provides clean edges to assure uniformity from coil to coil. By using quartz and applying a polyimide coating we produce a device that eliminates the need for conformal coating or staking. Inductors can be epoxied down with nonconductive epoxy and the wire bonded for connection.
-
product
Custom Test Fixtures
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
-
product
High Speed & Precision Pressure Insensitive Mass Flow Module
D700MG
Critical semiconductor manufacturing processes continuously desire precision gas flow control devices that enable both future innovation, and lab to fab transition of leading edge memory and logic device. HORIBA's propose the new pressure based MFC D700MG, the upper compatible model of the D500MG to support customer’s challenges.
-
product
Plugbord
3797-2
VECTOR Electronics and Technology, Inc.
30 Gold plated edge contacts (15 each side) on 0.156"(3.96mm) centers. 3-Hole solder pads for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only.Convenient easy-to-read hole marking legend on wiring side.
