Filter Results By:
Products
Applications
Manufacturers
Drivers
translate general instructions into hardware specfic commands.
-
product
RGB Video Driver
PCI900
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
product
Replacement of Legacy Instruments with New Compatible Instruments, without Modifying the Existing Software, Drivers, or TPSs
WinTE 7000
Replacement of legacy instruments with new instruments, without modifying the existing software, drivers, or TPSs.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Intelligent Interface Card
IIB-1553-PC104+
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
1100 HP Water Brake Chassis Dynamometer
CM-51
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
product
RS-422 RS-423 RS-485
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
product
Mainframes
Our CompactPCI series mainframes are industry-standard, open-architecture chassis with enhancements to support Pulse Instruments' clock driver and DC bias cards. The enhancements are transparent to the CompactPCI specification, and 3rd-party cards CompactPCI/PXI cards can be used in our mainframes without hardware or software modification*.
-
product
PXI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779123-01
32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Imaging Modules
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
product
RF Amplifiers
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
product
Laser
BDS-MM Series
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz / 50 MHz*Free Beam or Fiber Output*Optical Power Up to 40 mW*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
product
PXI-5122, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
778756-02
100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXI‑5122 high-resolution PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth. The PXI‑5122 also features PXI synchronization and data streaming capabilities.
-
product
Torque Tester
WDISR-RL series
Separate type digital torque driver. The detector is compact and lightweight, for the control of small torque . Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level. Various screw tightening tests, final tightening checks, tightening data storage, etc.
-
product
LED Driver Aging Rack
LEDRACK-100W192P
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
product
Mixed Signal Test Systems
MTS2010i
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
PXI Transfer Switch Module
PXI Transfer Switch Modules offer fast insertion times and low insertion loss to switch loads at RF frequencies. The modules also have 50 impedance that helps minimize reflections of the RF signal and protect your instruments. You can program the PXI Transfer Switch Module using the NI-SWITCH instrument driver.
-
product
PXI-5153, 500 MHz, 2 GS/s, 8-Bit PXI Oscilloscope
780317-03
500 MHz, 2 GS/s, 8-Bit PXI Oscilloscope—The PXI‑5153 high-speed PXI oscilloscope has two channels with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations. The PXI‑5153 also features PXI synchronization and data streaming capabilities.
-
product
Four Channel Load Cell Tester
LCIC-4HS
Industrial Measurement Systems Ltd.
Four Channel Load Cell Interface Card Model LCIC-4HS The LCIC-4HS is a four channel load-cell interface board for the IBM PC/AT and compatible computers (ISA Bus). This board was especially designed to fit very fast and real-time weighing applications such as multi-head fillers. It supports up to four channels with one load-cell on each. All the necessary filters and the batching control functions are built on the board and are easily accessible by the user. Direct communication with the PC bus and high-frequency sampling enables the LCIC-4HS to handle all real-time applications and to achieve very high accuracy. The LCIC-4HS is memory-mapped. Up to 32 boards (128 channels) may be installed in a single PC. It comes with a detailed user manual and software utilities for easy installation and calibration as well as full examples for the programmer (including Win 95/98 drivers).
-
product
Automated Warning System
Is a safety system consisting of 3 different magnet types (AWS 1, 2 and 3) and a locomotive-mounted detector (MagSense), designed to aid drivers in observing the fixed signals, particularly under adverse weather conditions, and is supplementary to the fixed signals which the driver must observe.
-
product
USB-5132, 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
779969-02
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Advanced Vehicle Field Testing
Being responsive to customers’ is the top priority at Trialon Corporation. Trialon has a long-standing commitment to supporting our customers’ requirements on time every time, especially considering the speed of technological developments in Advanced Driver Assistance Systems (ADAS) and fully autonomous vehicles.
-
product
PXIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 4 Channels
M4X.6622-X4
The M4x.66xx-x4 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PXI Express (PXIe) cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x4 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4x series 625 MS/s AWG.
-
product
ChenYang Voltage Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
DC voltage sensor/transducer works according to Linear PhotoelectricalIsolation and is designed for applications to measurement and monitoring of DC voltage. Theoutput signal (DC voltage or current) of this transducer is proportional to the input DC voltage.They are suitable for measurements and long time monitoring of DC voltages and can applied topower supply management, DC motor drivers, battery chargers and systems etc.
-
product
PXIe-57857, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785586-01
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
Pulsed Lasers and LEDs
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
product
Rotary Actuators
A line of of products that combine a high rigidity hollow rotary table with a closed loop stepper motor and driver package. It retains the ease of use of a stepper motor, while also allowing for highly accurate positioning of large inertia loads.
-
product
Memory Analyzers
Market drivers in the memory sector have changed. Gone are the days of simply pushing Moore’s Law to ever faster data rates. The memory designs of today and tomorrow must also be smarter than ever before. Today, handheld and wearable computers must draw from a limited battery reserve while serving up fast, responsive, and compelling mobile experiences. Meanwhile the cloud of data centers and server farms that feed us these compelling experiences must continuously grow while simultaneously reducing overhead and environmental impact. These two different markets have the same goals: smarter memory, smarter control systems, and lower power usage.
