Filter Results By:
Products
Applications
Manufacturers
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
MTA Wiring Analyzer
2650
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-02
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It … also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
product
3U VPX Single-Board Computer
VP32003
LinkedHope Intelligent Technologies Co.,Ltd.
VP32003 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32003 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32003 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, RS232/422/485 interface and two USB2.0 interface.The data plane of VP32003 uses Serial RapidIO 2.0 bus, which can be configured as follows: 2x SRIOx4, 4x SRIOx2, 8x SRIOx1. This feature makes it suitable for either distributed switching system or centralized switching system.
-
product
cDAQ-9188, 8‑Slot, Ethernet CompactDAQ Chassis
781424-01
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
product
Distributed 4-Axis Motion Control Modules (with High-Speed Trigger Function)
MNET-4XMO-(C)
The MNET-4XMO is a 4-axis motion controller module for Motionnet distributed motion systems. It can generate fast frequency pulses (9.9 MHz) to drive stepper or servomotors in the machine automation field. As a motion controller, it can provide comprehensive motion functions which include 2 axis circular interpolation, 2-4 axis linear interpolation, or continuous interpolation for continual velocity and so on. Also, changing position/speed on the fly is available with a single axis operation.
-
product
Optical Distributed Sensor Interrogator
ODiSI 6000 Series
The ODiSI 6000 Series is a powerful measurement system specifically designed to address the modern test challenges of advanced materials and systems. The ODiSI system delivers the highest definition distributed sensing of strain and temperature available, giving you maximum insight and visibility into your component or process.
-
product
Regenerative Grid Simulator
61800 series
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
product
ISC-1781, 1.3 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785147-01
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7856
The PCIe-7856 is a PCI Express interface card providing two ports for Motionnet and HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
product
DAS
The Distributed Antenna Systems (DAS) function is to enhance the performance of a wireless network coverage of a specific area. DAS is a network of antennas which are all connected to the same source. The DAS solution is more efficient than having a large single antenna to cover an area and that’s why it is highly suited for in-buildings service and a restricted outdoor area. Amphenol Procom offers a wide range of both indoor antennas and passive devices, especially for Public Safety applications.
-
product
DAS / 4G LTE Power Dividers, Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers wideband RF power divider / combiners optimized for DAS (Distributed Antenna System), 3G, and 4G LTE modem gateway splitting applications. INSTOCK cell-band and DAS splitters are commonly used for in-building wireless (IBW) network deployments. Available in 2-way thru 48-way configurations spanning 698-2700 MHz with exceptional performance. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
product
cRIO-9056, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller
786426-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller - The cRIO-9056 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers one Gigabit Ethernet port, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
Low Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
product
DC/DC Power Supply
ISM-DC-AT512-P
The ISM-DC-AT512-P is a dual output, DC/DC power supply designed for small form factor embedded systems. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/COTS, security, solar-powered, and telecommunications.
-
product
General Purpose I/O Modules
HY-TTC 30XH
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
product
Extension Unit
ZET 452 MP
The ZET 452 MP extension unit improves the capabilities of electric circuit parameter control devices:*increases the number of measuring circuits;*makes it possible to build distributed systems for cable networks checking.
-
product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7853
The PCIe-7853 is a PCI Express interface card HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
product
Distributed Antenna Systems (DAS)
Morcom's DAS as a Service (DAaS) is a new offering in the Connectivity as a Service (CaaS) portfolio. Distributed Antenna Systems (DAS) are an appealing option for building owners and real estate venue operators. Why incur in the capital expense of purchasing a DAS when you can have the same cellular coverage in your venue and pay for it as a monthly expense (where it will be offset by the money you're saving through IoT innovation and productivity). Morcom’s CBRS Private LTE band and Neutral Host DAS solutions are available to all carriers.
-
product
Ship Auxiliary System Monitor
A distributed system consisting of a variable number of intelligent measuring units, a central computer located on board a ship, and a remote computer on the shore, with the ability to configure and analyze measured signals via the Internet. Intelligent measuring units are built on the basis of the industrial measuring platform PXI.
-
product
RangeNet software
RangeNet
Command and Control Technologies Inc.
RangeNet software is designed to simplify creation of distributed range control systems and enhance situational awareness of command, safety, and range personnel. It is a modular framework that is easily adapted and extended to a variety of mission types anywhere in the world. It integrates planning, configuration, simulation, training, mission execution & post mission analysis under an integrated architecture. RangeNet is a “plug-in” software module of the Command and Control Toolkit™ (CCTK), the real-time command and control middleware from CCT.
-
product
cRIO-9057, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 8-Slot CompactRIO Controller
786427-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 100T FPGA, 8-Slot CompactRIO Controller - The cRIO-9057 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
ISC-1782, 2 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785151-01
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
ISC-1780, VGA, 1.58 GHz Processor, Monochrome/Color Smart Camera
785143-01
The ISC‑1780 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic controllers (PLCs), human machine interfaces (HMIs), robotics, sensors, and industrial machinery. You can configure NI Smart Cameras with the included Vision Builder for Automated Inspection (AI) software or program the camera with the LabVIEW Real‑Time Module and the Vision Development Module.
-
product
Distributed Motion Controller
As smart factories continue to expand the scale of their operations, more reliable and stable motion control axes and I/O points are required to meet the growing demand of adding more connected equipment. Other than centralized motion controllers, ADLINK provides complete and scalable distributed motion control solutions for machine automation for improved system expansion by supporting more than 256 axes and over 2000 I/O points with wiring that exceeds 100 meters for large-scale motion control automation such as electronic parts manufacturing.
-
product
Performance Testing
Our Load Testing and Performance Testing expertise spans many technologies, including web, mobile, distributed, cloud databases, high-volume transaction systems, and more. UpDoer Technology is dedicated to professional excellence in all that we do for our many clients across the globe.
-
product
3U VPX Board
VP32004
LinkedHope Intelligent Technologies Co.,Ltd.
VP32004 is a high-performance PC-based 3U VPX processor board developed by Linkedhope®. It supports 3rd Gen Intel Core series processor and Intel QM77 chipset. It supports up to 16GB of on-board DDR3 ECC memory and supports mSATA SSD. In order to ensure that VP32004 works stably in a strong shock and vibration environment. VP32004 provides rich I/O interface, including 2x SATA III channels, 2x 1000 Base-BX/T, 1x RS232 front debug serial port, 3x RS232/422/485 interfaces (BIOS configurable), 4x USB2.0 interface, 1x USB3.0 interface, 1x Mini-DisplayPort display interface, 1x rear VGA display interface, 1x PS/2 interface.The board provides a flexible PCIe bus interface to the backplane that supports multiple configurations and can be configured as 1 x8, 2 x4, 4 x2 PCIe. This feature makes it suitable for both distributed and centralized switching systems.
-
product
Gunshot Detection & Localization System
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
product
EtherCAT Slave System
EU Series
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes Talos master controllers, EU & EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EU slave system brings the powerful flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EU system incorporates and controls nearly any type of I/O devices. Uniquely designed for full operability in conditions from 0°C to 55°C, the EU slave system is also fully compliant with the EN 61131-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certificate.
