Filter Results By:
Products
Applications
Manufacturers
Data Generators
Create and output test data.
-
product
FPGA PXI Card with 40 Channel ECL Buffer Module
GX3640
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
product
Gigabit Ethernet Tester
GET-100
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
product
Bi-Directional Differential-TTL I/O PXI Card
GX5641
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), Functional Test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) and can be individually set to operate in either conversion or static I/O modes.
-
product
Firmware
Field-Programmable Gate Arrays (FPGAs) are an ideal fit for data acquisition systems as they offer unparalleled real-time signal processing power. Moving functionality from the host PC to the on-board FPGAs helps offload the PCs central processing unit (CPU) and relaxes data transfer rate requirements. This capability is key in achieving the performance levels needed in many of today's leading-edge applications.All our data acquisition and generation modules host Xilinx FPGAs and are delivered with pre-installed general data acquisition firmware (for ADQ7 and ADQ14 we refer to this firmware as "FWDAQ"). In addition to the standard/default firmware, we also offer optional firmware development kits (available for all models) and application-specific firmware packages (available for ADQ7 and ADQ14 only). More information about these below.
-
product
Migration to Windows platforms
PDP-11, HP1000 and Nova / Eclipse
The ultimate migration approach for legacy 16-bit minicomputers and applications, Strobe hardware/software emulation products execute RSX, RSTS and RT-11 (DEC PDP-11), RTE (HP1000) and RDOS (Data General Nova and Eclipse) in a Windows environment on enterprise PC technology. Migrating complete applications from the minicomputer to Strobe Data's Osprey, Kestrel or Hawk ordinarily takes less than a day.
-
product
Universal Flash Storage
UFS
Universal Flash Storage (UFS) is a JEDEC standard for high performance mobile storage devices suitable for next generation data storage. The UFS is also adopted by MIPI as a data transfer standard designed for mobile systems. Most UFS applications require large storage capacity for data and boot code. Applications include mobile phones, tablets, DSC, PMP, MP3, and other applications requiring mass storage, boot storage, XiP or external cards. The UFS standard is a simple, but high-performance, serial interface that efficiently moves data between a host processor and mass storage devices. USF transfers follow the SCSI model, but with a subset of SCSI commands.The Arasan UFS IP family consists of Host controller IP, Device controller IP, and MPHY.
-
product
Clamp Meters
Rishabh Instruments Pvt. Ltd.,
Measures, calculates and displays power parameters of single phase or three phase systems. It features bluetooth communication with Android Mobile App. and software for PC for Data Logging, report Generation & Analysis
-
product
Evaluation and Data Mining
Magpie
LXinstruments Magpie is a user-friendly evaluation and data mining application for our test database. The data to be evaluated can be preselected via complex, easily configurable filters. Based on the selected data, it is then possible to create reports and perform statistical evaluations as well as machine capability analyses. The graphical GUI supports easy administration of the database by authorized users.The LXinstruments Magpie evaluation licenses are always linked to the data source, which would generally mean a test system. The test data generated by the test system will be marked as available for evaluation while it is stored in the database.
-
product
FEA and Strain Gauge Testing
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.825-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
product
Simulation And Analysis Software
fcXplorer Analyzer
Avionic Interface Fiber Channel Simulation and Analysis Test Software, fcXplorer, is an easy-to-use graphical user interface for Fiber Channel Simulyzer modules. fcXplorer is designed for troubleshooting, optimization, planning and configuration of fiber channel data. The low and high level protocol analysis offers acquisition, filtering, time stamping and interpretation of Fiber Channel data traffic and generates statistics.
-
product
Multi-omics Analysis Package
The Multi-omics Analysis Package, developed for metabolic engineering applications, provides the ability to automatically generate metabolic maps and perform a variety of data analysis for the vast data generated in fields like metabolomics, proteomics and flux analysis. It offers a powerful platform to support drug discovery, bioengineering and other life science research applications.
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
product
Fiber Channel Simulyzer
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.806-08
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Arbitrary Load-Control Device Characterization
S94522B
The S94522B Arbitrary Load Control Device Characterization application. Ideal for bare transistor compact modeling. Generate Keysight’s DynaFET compact model or use large signal waveform data to generate models.
-
product
Software Mobile Apps MindSphere
MindSphere
Siemens Digital Industries Software
MindSphere is the cloud-based, open IoT operating system from Siemens that connects your products, plants, systems, and machines, enabling you to harness the wealth of data generated by the Internet of Things (IoT) with advanced analytics.
-
product
DYNAMIC SIGNAL ANALYZERS
900 Series
The new SignalCalc 900 Series software makes the process of defining a test, making measurements, analyzing data and generating high-quality reports easier than ever before. All setup, project, test article, and customer information is saved along with measurement data in a database. Easily search for data from different test runs and test types for analysis and report generation.
-
product
SMS Data Logger
To alert a user when process parameter exceeds the limits is an important function of a data logger. The IM2000 series normally provides alarm relay outputs and the user can have common relay for all channels or can have individual relays for each channel. These channels can be grouped as well. Apart from the user, the other concerned persons in the plant should know that there is an alarm. SMS Data Logger / GPRS Data Logger generate a text alarm message as soon as the alarm condition is observed. SMS technology can be used to send periodical process updates as well. It can be used to send data to remote PC connected to GSM Modem. Information can be transferred with the help of GPRS technology as well. Thus the field conditions can be monitored any where in the world at any given point of time.
-
product
Optical & Electrical Data/Pattern Generators
The Data/Pattern Generators offer both electrical and Optical outputs with standard and custom data patterns. PPG products cover data rates ranging from 100 Mb/s to 28.05 Gb/s.
-
product
Pattern Generators
Active Technologies Data Pattern Generators offer a complete and unique portfolio of instruments to address a wide range of applications starting from Digital Logic and Semiconductors characterization, Aerospace & Defense compliance testing, Mixed Signal Systems testing to Signal Integrity experiments.
-
product
Data Acquisition & Generator Boards
Meltronics Systemtech Data Acquisition & Generator Boards
-
product
Steering Test Equipment: Software & Hardware
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
-
product
Metallographic Analyzer
MDS-5000D
Wuxi Jinyibo Instrument Technology Co., Ltd.
1) the Integrated T -shaped Mirror Design, PROVIDING Superior Stability 2) Low-position Front Operation, Ergonomic requirements . 3) 6V / 30W Adjustable Halogen LAMP, PROVIDING Ample Bright Lighting System . 4) 3/8 splitting of Tube The trinocular , Observation and photography can be carried out simultaneous 5) Low-position mechanical moving platform to quickly locate the image 6) Professional flat-field metallographic objective lens, providing good resolution and clear image 7) Polarization Detecting partial inserts, related polarized light observation mode 8 )Five-hole rotary disc type color filter, easy to operate and switch 9) Adjustable field of view diaphragm and aperture diaphragm, providing good contrast metallographic analysis software system CCD camera will The optical image from the microscope is converted into a video signal, and the Sample image under the microscope is input into the computer through the image acquisition card / digital camera, and the digital image is processed and measured by the software, and finally the image and the measurement result are printed. Back up images and measurement data. General system:General image processing functions: image acquisition, data backup, depth of field expansion, grain boundary reconstruction, image stitching, image calculation, filtering, Image annotation, image segmentation and processing, accurate printing. Professional analysis system: 1. Rating: based on inspection Standards, more than 200 software functional modules in more than 100 categories.
-
product
Streak Tubes
Streak tubes are the most important modules of streak cameras used for the study of ultra fast optical phenomena. The latter cameras are tools of critical importance in many areas of science and technology like studies of plasma/electric discharge/ combustion/laser ablation/ condensed matter phenomenon, in optical communications, electron beam acceleration technology, photochemistry, medicine, biology etc. Streak cameras have made possible a series of important scientific discoveries in earlier mentioned areas of science and technology. Precision information about parameters of streak tubes is needed both by manufacturer of such tubes in improve tube design and by users of these tubes to correct data generated by the tubes and make possible more accurate interpretation of output images.
-
product
Network Sensor Interface for USB Pressure Transducers
SI314
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
-
product
Model Based Testing
RTT-MBT
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
