Filter Results By:
Products
Applications
Manufacturers
Data Acquisition Systems
sense, log and store information. AKA: DAS
See Also: Data Acquisition, PCI Data Acquisition, DAQ
-
product
Data Recording System
DataMAX II
DataMAX II is a state-of-the-art Windows 2000 based analog instrumentation recorder designed to replace traditional tape based data recorders. Using the latest technology, DataMAX II eliminates the time consuming methods of the past with a single precision instrument that will replace a tape recorder, data acquisition system, and monitoring scopes. From calibration to analysis, a test can now be run in a fraction of the time, with far greater accuracy than was possible with traditional analog recorders.
-
product
System Synchronizer and Distribution Board - VME
Model 6891
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
product
PXI 20 Banks of 8 Channel 1 Pole MUX
40-615-022-20/8/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Brinell Optical Scanning System
B.O.S.S.
Newage Testing Instruments, Inc.
The B.O.S.S. brinell optical scanning system measures your brinell impressions faster, more accurately and more consistently. And it improves your quality control with advanced data acquisition and analysis capabilities, including the ability to save your high-resolution image of our impression to file.
-
product
DUT Matrix 32 DUT Matrix Channels
40-530-021
The 40-530-021 is a high density 32x8 1 pole reed relay matrix. Typical applications are signal routing in functional ATE and data acquisition systems. It consists of highly reliable sputtered ruthenium reed relays that offer >10e9 switching cycles to ensure maximum switching reliability with a long service life and stable contact resistance. Larger arrays can be built by daisy-chaining the common signals from multiple PXI modules
-
product
High Intensity Pulsed Solar Simulator
GEN 2
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
product
Isolated Digital Expansion Board
MSXB 078
The Microstar Laboratories Isolated Digital Expansion Board, part number MSXB 078, provides isolated digital expansion for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing errors from high-channel count digital I/O.
-
product
Data Acquisition Systems
m+p Coda is a full-featured turnkey software platform for data acquisition, signal analysis and monitoring. Complete turnkey operation provides quicker time to test by eliminating costly application programming and long learning curves. The extensive built-in features and tools offer a functionality that was previously available only in custom packages. The intuitive graphical user interface facilitates set-up, operation and analysis, thus leading to precise, repeatable results quickly.
-
product
PXI Multiplexer, Dual 32-Channel, 1-Pole
40-630A-022-D/32/1
The 40-630A-022-D/32/1 is a dual 32-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI MUX 4 Banks of 16 Channel 2 Pole
40-610-022-4/16/2
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
Ruggedized Ethernet Data Acquisition Systems
Series 7000
The Series 7000 Ruggedized Ethernet DAS brings new capabilities and levels of performance to transducer data acquisition. The ruggedized system is designed for installation in wind tunnels, engine test stands and other facilities where it is desired to locate the DAS on or near the test article, reducing installation and cable costs while improving signal quality and reliability. Each unit is a network appliance which conditions, amplifies and digitizes outputs from transducers. Multiple units are easily combined and distributable for larger installations. Real-time temperature Compensation of gain offset and Excitation Voltage, quality signal conditioning with high gain and a 24-Bit A/D per channel provide a high accuracy and high resolution DAS that will perform across a wide operating range.
-
product
PXI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
40-635A-106
The 40-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
R4
4 - Compact High Channel Count DAQ SystemCompact data acquisition system with up to 64 analog inputs, 32 counter inputs and 32 analog outputs with built-in high-performance, highly reliable data processing computer and SSD data logger.
-
product
Signal Conditioning
Signal conditioning is a vital part of the data acquisition process and measurement chain. Poor choice of signal conditioning can seriously compromise the overall quality of the measurements taken by any data acquisition system and as a result the choice of conditioning equipment is important when specifying a measurement solution.
-
product
Signal Conditioning and Filtering
MSXB 065
The MSXB 065 Signal Conditioning Expansion Board provides filtered analog signal conditioning for voltage signals for Data Acquisition Processor systems. Each board has differential inputs; jumper-selectable simultaneous sampling; jumper-selectable gains of 1, 5, and 25; fourth-order anti-alias filters, cutoff frequencies from 100 Hz to 50 kHz.
-
product
PXI 2A Multiplexer, 2-Bank, 16-Channel 4-Pole
40-614-012
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXI MUX 8 Banks of 8 Channel 2 Pole
40-610-022-8/8/2
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
product
Omni-λSeries Imaging Spectrograph
Omni-λi
Zolix Imaging Spectrometer includes different focal length 320mm, 500mm, 750mm; ◆Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. • More than 100 gratings for the best spectral range, throughput and dispersion to meet your application◆DSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioning◆Optional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuation◆Installation and set-up through USB 2.0 computer interfaces • Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications◆ Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programs◆ZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up
-
product
Data Accquisition
High-performance data acquisition system that is designed to perform well during intense, demanding testing.
-
product
Remote Testing For Communities
imc WEBDEVICES
imc WEBDEVICES provides the means for remote-controlled, unmanned, fully-automatic monitoring, data acquisition and testing of technical systems over long distances, such as with vehicles, machinery, plants or structures.
-
product
Fracture Mechanics Clip-On Gages
Model 3541
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
PXI MUX 8 Banks of 16 Channel 1 Pole
40-610-022-8/16/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71620
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
DAS
The Distributed Antenna Systems (DAS) function is to enhance the performance of a wireless network coverage of a specific area. DAS is a network of antennas which are all connected to the same source. The DAS solution is more efficient than having a large single antenna to cover an area and that’s why it is highly suited for in-buildings service and a restricted outdoor area. Amphenol Procom offers a wide range of both indoor antennas and passive devices, especially for Public Safety applications.
-
product
PXI 2A Multiplexer, 1-Bank, 32-Channel 4-Pole
40-614-017
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Computer Automated Data Acquisition
System 471
The NEFF System 471 (S471) DAS is a complete moderate-speed DAS for use in computer-based applications. The S471 is designed primarily for computer automated data acquisition in test facilities, laboratories and industrial plants or wherever a moderate-speed, high accuracy DAS operating in high common-mode voltage environments is required.
-
product
IRIG Time Code Receiver & Generator Module
TCR180
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
product
Production and Laboratory OTDR
8000
The 8000 OTDR is the first of a new generation of OTDRs that has been designed specifically for optical fiber and cable test applications. Its revolutionary "performance first" optical design delivers unsurpassed optical performance, and its MS Windows operating system facilitates integration of the OTDR into manufacturing networks. These features, combined with unique data acquisition capabilities, significantly reduce the time associated with many aspects of the OTDR measurement process, making it possible for fiber and cable manufacturers to increase production output and reduce manufacturing costs.
-
product
Software
DASYLAB Lite
Dasylab lite software for operation of our line of THERMES Data Acquisition Systems. For customers who already have Labview or Dasylab no additional software is necessary. Recommended operating software is Dasylab Lite version 10. The lite version provides all the necessary functions to display and store temperature data in digital and graphical formats in real time. Users may customize the display to suit their particular application. The Dasylab Basic version provides additional features for data manipulation and statistical analysis.
