Filter Results By:
Products
Applications
Manufacturers
-
product
Solid State Voltage Injector
J2110A
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
product
Programmable Current Preamplifier
99539
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
product
Test Fixture Kits
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
product
Audio Circuit Tester
25500
Handy device for locating short and open circuits. Horn sounds when circuit is complete. Long 5 foot leads permit technicians to work around corners, under dash boards and in trunks. For use on all 6 and 12 volt circuits.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Silver Plated Test Points
The fabricators of SMT printed circuit boards may take advantage of the convenience of field testing with the unique loop design of Components Corporation's TP-107 and TP-108 series of surface mounted, printed circuit test points is now available in silver-plate for outstanding reliability. All products are RoHS and REACH compliant.
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
Appliance/Tool Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• Lowest Board Count In Industry• No Proprietary Circuit Boards• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
product
Reflow Soldering Machines
Shenzhen Leadsmt Technology Co.,Ltd
Used to attach surface-mount components to printed circuit boards (PCBs). It involves applying solder paste to specific locations on a PCB, placing the components on the paste, and then heating the assembly in a reflow oven.
-
product
High Carbon Process Carrier Pallets
Composite Family
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
product
Functional Testing of Printed Circuit Boards, Sub Assemblies and Finished Products
Testpoint
Yelo Testpoint is an extremely modular and flexible system, allowing you to scale to any size operation, and to add almost any new test requirements. Ideally suited to cellular manufacturing, the system can be used to complement an existing ATE, as a functional test add-on, or as a diagnostic work station. Its compact, space-saving construction has multiple interface positions to accommodate both horizontal and vertical connections.
-
product
Functional & ICT Tester
igentic® 621t
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
product
LC-4.5 Voltmeter
5203
Model LC-4.5 is the first hand-held voltmeter to include a number of special features which facilitate corrosion and cathodic protection testing on underground structures. It is designed for field testing under almost any environmental conditions. Sealed Mil Spec. switches, sealed windows, a gasketed case and a printed circuit board with baked-on moisture and fungus resistant coating on both sides make this possible.
-
product
Digital/Analog/Frequency Measurement Module
JT 2149/DAF
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
product
Embedded Boards
UltraZed Family
Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.
-
product
Plugbord
838WE
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers.No circuit pattern, edge contacts only.Holes on 0.100" hex pitch, "G" patternDesign for mounting transistors. Unrestricted component placement over entire board surface.
-
product
In-Circuit Test Systems
Keysight offers leading board test solutions for electronics manufacturers to tackle a wide range of PCBA test access and coverage issues for today's complex printed circuit assemblies.
-
product
ASA200
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
product
Extender
3690-15
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards.
-
product
QMA Connectors
Pasternack QMA connector category contains dozens of part numbers, most of which are RoHS and REACH compliant. QMA connector series in this category will terminate to coax or PCB (printed circuit board). Our QMA connectors are built to precise microwave and RF industry specifications. QMA connector products are manufactured in male or female gender with 50 Ohm impedance. Connectors in the QMA category are available in straight or right angle versions, as well as, bulkhead or mountless options. These QMA connector designs include crimp/solder, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this QMA connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
product
Fastest In-Circuit Test Platform
TestStation
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
product
PHOTOMASK INSPECTION MACHINE
NEGATIVE FILM
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
product
Flying Probe Test System
A8a
The A8a test system provides the flexibility of flying probe testers while delivering high throughput testing for bare board printed circuit boards (PCBs). The target market for the A8a is the electrical test of tablet and PC motherboards and high density interconnect (HDI) products for smart phones. The A8a is designed for high productivity, reliability and test accuracy. To achieve high throughput the key feature of the A8a is a new dual shuttle system, which reduces the product exchange time to zero seconds in automation mode. In combination with the fast test speed of up to 140 measurements/second the A8a will give customers a competitive test solution for batches up to 5000 boards. A typical cycle time of a 4-up smart phone board is about 2 minutes.
-
product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
product
PXI Breadboard Module, 2-Slot, 37-Pin D-Type
40-220A-202
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
High Flexibility Test Controller Card
TCC 1800-UE
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
product
RTM Communication Board
MS 3636I
CPCI Rear IO Communication Board is a signal conditioning and interface board for CPCI Integrated Communication Card (MS3635i). This board has required signal conditioning and interface circuits for RS422. Two 96 Pin Euro Connectors are used to interface all IO’s.
-
product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Mezzanine System
5047
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
product
PXI 12 Channel High Voltage Multiplexer
40-320-001
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
