Filter Results By:
Products
Applications
Manufacturers
Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
PMC Carrier with 2 Positions
PMC-MC-X2-28
PMC-MC-X2 adapter/carrier/motherboard provides the ability to install up to 2 (two) PMC cards into a small enclosure. PMC-MC-X2 has one PMC card mounted front and one rear to create a compact arrangement with 2 PMC positions. The carrier provides power supplies for the +5, +3.3, +12, and minus 12 from a reference supply.
-
product
Modulators
A modulator is an electronic circuit that superimposes a low-frequency (information) signal onto a high-frequency (carrier) signal for the purpose of wireless transmission. The reason for this is that higher frequency signals can be received using shorter aerials, which are more practical than longer ones. The information signal can be either analog or digital.
-
product
Carrier Card
CPMC1
The CPMC1 PMC carrier board is a mechanical adapter that holds one PMC in a 3U CompactPCI slot. The carrier supports air and conduction cooling as well as front and rear I/O. The operating temperature range is -40°C to +85°C.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
1x4 Multiplexer Plug-In
1260-134
The Astronics1260-134 is a sixteen 1x4 multiplexer plug-in card for the Adapt-a-Switch® platform. It installs, easily and directly from the front panel, into the Adapt-a-Switch VXI Carrier, 1260-100.
-
product
AMC GBit link card/VITA 57 FMC carrier
SIS8100
The SIS8100 will be a single width mid height AdancedMC card. It will interface with a single PCI Express lane over a PLX Technology PEX811 PCI Express to local bus bridge chip and have an on board Virtex IV FPGA. The default stuffing option has a Small Form Factor (SFF) optical link medium that can be operated at 1, 2.5 and 4 GBit/s.
-
product
4-slot LXI Chassis
MezaBOX-4M LXI
MezaBOX-4M LXI is a device that ensures the operation of various mezzanine modules (up to 4) installed in it, under the control of a personal computer via USB2.0 or ETHERNET 10/100/1000 Base T (local area network) interfaces of a personal computer ... MezaBOX-4M LXI is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog.
-
product
Transition Module for 3U cPCI PMC Carrier
TCP030-TM
The TCP030-TM is a 3U Transition Module to be used with 3U cPCI PMC carrier like TEWS TCP27011R. It provides easy access to the PMC I/O lines of cPCI PMC carrier with back I/O.
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
Tone Receiver/Decoder
Kratos Defense & Security Solutions, Inc.
The Tone Receiver/Decoder is a rack-mount receiver that will display the presence of any of the 20 IRIG standard tones, transmitted either individually or in combination as command tones (e.g. Monitor, Arm, Destruct, etc.). It accepts a universal AC power input, and it can be tuned in 100kHz steps for carrier signals in the range of 406MHz – 450MHz compliant to RCC 313 and 319 for compliant IRIG tones.
-
product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - 3U VPX
Model 5973-312
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Also available as Model 7070-312- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
-
product
OpenVPX PMC/XMC carrier.
EnsembleSeries™ CCM6020
*First OpenVPX carrier module designed specifically to use the Expansion Plane*PCI/PCI-X interface at up tof 133 MHz on each site*x8, x4 and x1 PCIe interfaces*Advanced OpenVPX system management functionality enables remote monitoring, alarm management, and hardware revision and health management*Conduction-cooled and air-cooled variants available
-
product
PTP Grandmaster
OSA 5335
Our OSA 5335 Modular PTP Grandmaster is a scale-able and high-performance IEEE 1588 v2 standard compliant Grandmaster Clock for the distribution of frequency, phase and time synchronization over packet-based network infrastructure including IP/MPLS, Carrier Ethernet, PON and DSL networks. Its carrier-class design provides high client capacity and a wide range of redundancy options to deliver scale-able performance and maximum availability. Our OSA 5335 is designed to deliver precise and reliable frequency, phase and time-of-day information in markets including telecommunications, media broadcast and power utility communications.
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
product
High Carbon Process Carrier Pallets
Composite Family
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
product
Mezzanine Carrier
VXI NM-M
HM-M is a carrier of mezzanine modules in the VXI standard, it is a VXI module of the size C-1. NM-M ensures the functioning of various modules installed in it, made in the form of mezzanines. NM-M is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog. The carrier of the NM-M mezzanine modules is used as part of information measuring systems based on the VXIbus trunk. Made on a C size board in accordance with the requirements of the IEEE Std 1155-1992 standard.
-
product
96-Pin Micro-D Connector Block, Female With Backshell
44-965-096-F
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D BRIC connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
product
Mezzanine System
5174
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
product
Nexis GC-2030 BIDUFRGA
UFRGA Series
The Ultrafast RGA system utilizes the new Barrier Discharge Ionization Detector (BID) technology coupled with Nexis GC-2030 to create new system GC for ultrafast, high-sensitivity analysis. Since the electrode creating Helium plasma is totally isolated from the carrier gas, there is no chance to contaminate this electrode with a dirty sample. This enables long-term stability.
-
product
Intelligent ARINC Interface Module
M4K717
The M4K717 is an intelligent ARINC 717 interface module for the multiprotocol Excalibur 4000 family of carrier boards.The module supports two ARINC 717 receive channels and two transmit channels.In transmit mode, the module sends the four subframes from a pre-defined buffer in dual-port RAM.In receive mode, the module stores all subframes with status and Time Tag information appended to each subframe.The M4K717 comes complete with C-driver software library including the source code.
-
product
Signal Conditioning Carrier
ProDAQ 5720
The ProDAQ 5720 Signal Conditioning Unit provides power and cooling for up to two Signal Conditioning Cards from the ProDAQ 58xx Series. These Signal Conditioning Cards provide conditioning for 8 or 16 channels and can be used directly with Bustec’s high-performance ProDAQ ADC function cards such as the ProDAQ 3416 16-ch. Sigma-Delta ADC Function Card or the ProDAQ 3424 8-ch. Sigma-Delta ADC Function Card.To connect the function cards to the signal conditioning cards SCSI-style cables from the ProDAQ 8010-Bx Series are used. They provide shielded twisted pair connections for signals and control.
-
product
Interface Card
XMC-WMUX
Alta Data Technologies’ XMC-WMUX interface module (PCI Express Mezzanine Card for Carriers and Single Board Computers or Carriers) is a single or dual-channel (A-B Redundant = 4 Busses per Channel/Wings) WMUX card supported by the latest software technologies.
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
18" Ribbon Cable
RCONM50-D25-2
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the PCI carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
product
IP Module with 2 CAN Ports
IP-CAN
The IP Module driver can be instantiated multiple times to control multiple cards by the same CPU. IP-CAN when coupled with the Dynamic Driver "knows" what slot it is in and which carrier it is installed into. The slot and carrier information is required when using multiple cards in a PCI/PCIe system with dynamic address assignment.
-
product
Power Amplifier
MS 2011
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
product
PCIe MiniCard Carrier
The PCIe MiniCard carrier offers four PCIe MiniCard sockets on a compact PCI/104 Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
