Filter Results By:
Products
Applications
Manufacturers
-
product
Extreme Rugged PC/104-Plus, PCI-104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM3-BT4
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
product
Analog-to-Digital Converter Board
VME-3125A
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
product
Embedded Single Board Computers
Advantech Embedded Single Board Computer (SBC) series include: 2.5" Pico-ITX, 3.5" PC/104, 5.25" EBX, and MI/O Extension form factors. They offer scalable x86 performance from low power to high-end, and from fanless and slim, to extended temperature platforms with longevity. They are ideal for system integration with high flexibility and expansion possibilities, and compact sizes with rich I/O. Reliability was built in for highly reliable 24/7 operation and industrial grade rugged operation.
-
product
3U OpenVPX High Density Multifunction I/O Board
68CB6
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
product
COM Express® Type 2 Reference Carrier Board in ATX Form Factor
Express-BASE
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
product
PXI Express Board Virtex-5 DAC Module1GHz, 14-bit DAC
SMT781
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or S XT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
product
Bit Waveform Digitizer Board
ATS9373
ATS9373 is a 12 bit waveform digitizer board that can sample one analog input at rates up to 4 GS/s or two inputs at 2 GS/s. With on-FPGA FFT signal processing and data throughput as fast as 6.8 GB/s (6800 MB/s), ATS9373 is an ideal solution for many applications, including next generation OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
product
Board
Arduino Micro
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
product
VMEbus board
IIB-429--VME-4C
The IIB-429-VME-4C provides 16 ARINC-429 compatible channels (8 receive and 8 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME-4C is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This VMEbus board has a 6U form factor. This VME unit is also available in a 3U form factor, as IIB-429-VME.
-
product
System Synchronizer and Distribution Board - VME
Model 6891
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
product
3U OpenVPX Multifunction I/O Board
68C3
NAI’s 68C3 is a 3U OpenVPX multifunction I/O and communication board with three function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Isolated Digital Expansion Board
MSXB 078
The Microstar Laboratories Isolated Digital Expansion Board, part number MSXB 078, provides isolated digital expansion for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing errors from high-channel count digital I/O.
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
Warm-Up Board
WECO 9000
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
product
Big Easy Driver
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
product
ATG Program
FS-ATG
FS-ATG is the world's easiest ATG program - pull-down menus, online help, and test generation wizard guide new users step-by-step through the process. It takes less than 2 minutes to 'point & click' a setup program for a board full of devices.Generates Vectors Faster Than EverFS-ATG is a 32-bit Windows 98/NT/2000 application that takes full advantage of today's powerful PC's. Small devices finish in seconds and most FPGAs / CPLDs, even the largest and most complex, can develop great tests after in just a few hours.
-
product
Open Source Hardware Test/Programming Fixture
OpenFixture
OpenFixture is a fully parametric programming/test fixturing solution written in openscad. The inputs are generated/captured from the users board layout software and a laser cuttable fixture is generated automagically.
-
product
PCI Module
PCI-1553-DDC-1,2
The PCI-1553-DDC uses Data Device Corporation’s ACE, DDC enhanced mini BU61865G4-290 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. This controller has 64Kx17 word of internal memory and internal transceivers for both channel A and B. The 3U PCI board has on-board transformers. This board has a PCI compliant interface
-
product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
product
LilyPad Light Sensor
The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from the board through the signal tab to the microcontroller you connect the sensor to. If the sensor receives no light, no current will flow through it. In a typical indoor lighting situation, the sensor will output around 1 to 2V. Adding this board into your next e-textile or wearable project will really open up the possibilities by being able to incorporate light level sensing capabilities.
-
product
Test Points
TestStation LX2
TestStation LX2 is Teradyne's largest pin count in-circuit test system. Configurable up to 15,360 pins, TestStation LX2 utilizes the new UltraPin II 128HD pin card for testing large, complex, and heavily-integrated printed circuit board assemblies.
-
product
Pico-ITX
RSB-3810
*MediaTek Genio 1200 4 cores A78 & 4 cores A55*Onboard LPDDR4 8GB, 4000MT/s memory*HDMI 4k60fps, 1 x Dual Channel 24 bit LVDS*1 x 4-wire RS-232/422/485, 2 x USB3.2 Gen1 By 1, 2 x USB2.0, 1 x Micro SD, 1 x Mic. in / Line out*1 x M.2 3052 Key B for 5G, 1 x M.2 2230 Key E Slot for WiFi/BT*Support I/O Expansions by UIO40-Express I/O boards*Support Ubuntu, Ycoto Linux and Android
-
product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 58610
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
product
Power over Ethernet (PoE) DC/DC
An isolated 25W, PC/104-Plus form factor, 802.3af/at compliant, PoE PD power supply. The Class 4 signature supports up to twice the power of 802.3af compliant PD devices. Designed to power a single board computer from DC power extracted from a CAT5 cable sourced by an 802.3af/at compliant PSE device configured as either an endpoint or midspan device.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
Board Level Voltmeters
We've shipped more than half-a-million on-board controllers (OBCs) to manufacturers across the world. Our non-contact OBCs offer the accurate, drift-free, high-speed, and low noise measurements your applications require.
-
product
Metal Alloy Low-Resistance Resistor: ACQ-200
LRA
*This specification is applicable to lead free, halogen free of RoHS directive for metal alloy low-resistance resistor.*This product is for general purpose.*LR-A series : AEC-Q200 qualified available.*Miniature size suitable for compact Print Circuit Boards of high-precision electronic products.
-
product
Pulse Generation Measurement Board
MS 1806
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
BGA Socket Adapter Systems
Advanced Interconnections Corp.
BGA Socket Adapter Systems convert surface mount device packages to through hole (pinned) assemblies, making it easy to plug and unplug SMT devices whether you are planning for future device upgrades, field programming at point of use, or need the ability to quickly swap out device packages in the field or the test lab. Protects valuable PC boards and saves time by eliminating the need to desolder packages during device removal.
-
product
Fusion Bonded Cable Jumpers
Series 152FB
Fusion Bonded Cable Jumpers. Aries Series 152FB Fusion Bonded Cable Jumpers are flexible...plug them directly into PC boards or sockets. Stranded wire conductors are fusion bonded with an overcoat of tin for easy soldering or socketing. Each jumper is shipped with protective tabs on both ends for maintaining proper conductor spacing.
