Filter Results By:
Products
Applications
Manufacturers
ATE Software
Software for equipment designed to automatically analyze functional or static parameters of electronic assemblies in order to evaluate performance degradation. (itmconsulting.org)
-
product
PXI Very High Density Versatile 2 Amp Multiplexer
40-612A-002
The 40-612A Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves. Typical applications include signal routing in ATE and data acquisition systems. The 40-612 module uses high quality electro-mechanical relays, connections are made via a front panel 160 pin DIN41612 connector. The module can be software configured into one of a large number of different multiplexer modes. Relays allow the multiplexer banks to be set in 1 or 2 pole mode and inter-bank switching enables the channel count to be increased up to a maximum of 128
-
product
PXI-2521, 40-Channel, 2 A, DPST PXI Relay Module
778572-21
40-Channel, 2 A, DPST PXI Relay Module—The PXI‑2521 is a general-purpose switch module that features independent double‑pole single‑throw (DPST) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2521 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXIe Arbitrary Waveform Generator, 500 MSa/s, 16 bit, 200 MHz
M3201A
The M3201A PXIe arbitrary waveform generator is ideal for general purpose AWG automated test requirements. It offers high channel density with high-quality output with low phase noise. The optional real-time sequencing, intermodulation synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including envelope tracking (ET) and DPD (part of PA/FEM reference solution), MIMO, baseband electronics design, wireless device manufacturing, ATE, beamforming and other multi-channel coherent signal generation and multi-channel signal generation.
-
product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
product
RF/Microwave ATE Systems
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
product
FPGA PXI Card with 40 Channel ECL Buffer Module
GX3640
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
product
RFIC ATE System
RI 7100A
The RI 7100A, which RI has shipped for over 10 years, has proven itself as the most advanced, reliable (> 4500 hours MTBF) and cost effective RFIC ATE System available. "Our recipe for high performance microwave test has always been dependent on an extremely elegant RF signal path while maintaining the most advanced microwave calibration software," said RI President, Mark Roos.
-
product
CASS Instrument Real Time Controller
External control of the Navy CASS ATE via Ethernet. Standardized graphical user interface (GUI) for individual control of each instrument independent of CASS software. Allows TPS developer or ATE maintainer to change/control instrument settings for TPS debug and instrument troubleshooting.
-
product
Super Fast Gang Industrial Universal Programmer
48Pro2AP
The Dataman 48Pro2AP is a super fast industrial universal programmer with ISP capabilities and USB 2.0 connectivity • Optimised for use in automated handlers and ATE machines • Over 71,000 devices supported with new devices added monthly • Mechanically stable case design with multiple fixing points • ISP capable using the JTAG interface • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
product
Programmable Digital Attenuator
LDA-602EH
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
-
product
PXI-2568, 31-Channel, 2 A, SPST PXI Relay Module
778572-68
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2568 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2568 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
Test-Stand Software for TD6 Controller for QMax ATE
TD6 TestStand Software
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
Semiconductor Test Software Solutions
The test engineering staff at Test Spectrum has developed hundreds of test software projects on all major ATE platforms for numerous product technologies.Whether you need to optimize a current test platform, convert to a lower cost test platform, or design a brand new program for a cutting edge product within incredible time constraints, the Test Spectrum team will exceed your program expectations with quality products and excellent results.
-
product
RF/Switching
SMX-6XXX (RF/Switching)
The VTI SMX-6xxx Series of high density non-blocking RF multiplexers deliver exceptional performance and reliability in a compact single-slot configuration. Front panel connectivity is available in both SMB and PKZ formats to integrate seamlessly into new or existing test systems. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers.The SMX-6xxx Series delivers unmatched bandwidth and isolation performance resulting in exceptional measurement integrity that is ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
product
Bench-Top & Shop Loader Solutions
Avionics Interface Technologies
To satisfy ARINC 615/615A data loader requirements in system engineering labs, avionics system manufacturing, and maintenance depot applications, AIT provides data loader software that can be used together with AIT’s full line of ARINC 429, ARINC 664, and Ethernet interface modules and integrated into a variety of host desktop PC systems and ATE environments. The F-SIM-LDR-615 software provides ARINC 615-3/4 data loader support and is compatible with all of AIT’s ARINC 429 interface modules. The F-SIM-LDR-615A software application provides ARINC 615A-1 /2/3 data loader support over Ethernet and ARINC 664 networks and is compatible with all of AIT’s ARINC 664/Ethernet interfaces modules. The F-SIM-LDR-615 and F-SIM-LDR-615A software products include both graphical user interface (GUI ) data loader applications and command line data loaders which are scriptable and can be called from shell scripts, batch files, and python for support of automated load operations.
-
product
NI's Electrical Functional Test Solution
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
product
Microwave Switches
SMX-7XXX (Microwave)
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
product
DSR Pattern Editor Software
M9192A
The Keysight M9192A DSR Pattern Editor Software adds additional advanced capability to the Keysight M9195A/B PXIe digital stimulus/response (PXI DSR) modules by providing a graphical user interface for the development system. M9195A/B error log files can be dragged-and-dropped into waveform editor which speeds up the debugging of tests; this gives immediate visibility of discrepancies between the expected state in the ATE patterns with that of the DUT.
-
product
PXI-2522, 53-Channel, 2 A, SPDT PXI Relay Module
778572-22
53-Channel, 2 A, SPDT PXI Relay Module - The PXI‑2522 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2522 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
Satellite ATE
MS 1123
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
product
RF ATE
IFF-7300S Series IFF/Crypto/TACAN Automated Test System. IRIS 2000/IRS 1200 ATE Software Revision Service. RF Expansion Module (RFEM).
-
product
14-slot Rack-Mountable PXI Chassis
PX2000-514A (TE1014)
Team Solutions' TE1014 (PX2000-514A) is a 14 slot, 19î rack-mountable chassis, which fully compies with the PXI and Compact PCI standards. All slots have full PXI functionality. Separate forced-air cooling is provided for the power supply and PXI slots. Fan noise is minimized by varying fan speed according to system temperature. Standard features include temperature and PSU monitoring with full software support. The expanded slot capability of the unit provides system integrators with a single-box solution, thus avoiding synchronization, integration and cost issues associated with multi-platform solutions. With a compact case size of 4U / 19î, the TE1014 (PX2000-514A) provides the small footprint required for today's ATE and Data Acquisition applications.
-
product
PXIe Arbitrary Waveform Generator, 1 GSa/s, 14 bit, 400 MHz
M3202A
The M3202A PXIe arbitrary waveform generator is ideal for general purpose AWG automated test requirements, Quantum Computing and massive MIMO research. It offers high channel density with high-quality output with low phase noise. The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including Quantum Computing research, 5G, wireless device manufacturing, ATE, MIMO, beamforming and other multi-channel coherent signal generation.
-
product
PXI-2523, 26-Channel, 2 A, DPDT PXI Relay Module
778572-23
26-Channel, 2 A, DPDT PXI Relay Module - The PXI‑2523 is a general-purpose switch module that features independent double‑pole double‑throw (DPDT) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2523 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
Test Program Sets (TPS)
Data Review, Corrections, & Generation (Reverse Engineering). Technical Requirement Documentation (TRD). Test Strategy Reports (TSR). Test Program Development – Software. TPS Sell-Off & Acceptance. Life-Cycle Support. Technical Interface Test Adaptors (ITA) – Hardware. Training - TPS Development, ATE/TPS Operator, Fault Diagnostic, ATE Maintenance.
-
product
Super Fast Industrial Gang Programmer
448Pro2AP
The Dataman 448Pro2AP is a super fast industrial gang programmer with four independent modules, ISP capabilities and USB 2.0 connectivity• Optimised for use in automated handlers and ATE machines • Over 71,000 devices supported with new devices added monthly • Mechanically stable case design with multiple fixing points • Independent modules supporting concurrent programming • ISP capable using the JTAG interface • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
product
NI TestStand Development Services
Simplicity AI have a high degree of ATE software development expertise using NI TestStand, in industry areas such as aerospace, defense and telecoms. With Certified TestStand Architects and Certified TestStand Developers on the engineering team, and holding National Instruments Alliance Partner status, Simplicity AI have the knowledge and experience to deliver advanced test software solutions.
-
product
USB Controlled RF Signal Generators
Windfreak Technologies provides high value radio frequency devices such as RF Signal Generators, RF Synthesizers, RF Network Analyzers, RF Power Detectors, RF Mixers, and RF Frequency Converters. These devices can be used as RF Test and Measurement Equipment and controlled by Labview in an Automated Test Equipment (ATE) setup, or used as bolt-in RF modules in RF communications equipment. All products have innovative, powerful feature sets controlled by internal microprocessors so any settings can be memorized and used with or without a PC. Windfreak hardware also comes with the Labview GUI source code saving the end user hundreds of hours programming custom software. Use one of our RF Signal Generators or other products risk free. Return it if you dont like it.
-
product
software
The ATE Software GmbH is a small but nice software house in the center of Frankfurt. We stand for creative applications instead of interchangeable commodity. Therefore, we have upcoming IT technologies and trends always in view and provide our customers with "State Of The Art" software solutions that keep future requirements state.
