PT
a type of intrument transformer enabling secondary connected metering.
-
Product
1000BASE-T1 Ethernet Logging Expansion With Low Latency
PT-20MG
-
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
Product
Multi-Sensor Thermal Imaging Camera for Condition Monitoring
A310 PT
-
FLIR A310 pt thermal cameras can be installed almost anywhere to monitor the condition of your critical equipment and other valuable assets. Designed to help safeguard your plant and measure temperature differences, they allow you to see problems before they become costly failures -- preventing downtime and enhancing worker safety. FLIR A310 pt is ideal for various applications that require temperature measurement capabilities including: substation, transformer, waste bunker, and coal pile monitoring.
-
Product
WaveLink Dx20-PT Adjustable Positioner Tip Kit
Dx20-PT-KIT
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Modules - Modules, Automotive
-
Automotive modules from Vishay feature a range of technologies including FRED Pt®, High Voltage, MOSFETs, and Silicon Carbide (SiC).
-
Product
Current Transformer Tester
HTCT-300
-
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
Product
Isolated RTD Input Module
ADAM-3013
-
1000 VDC 3-way optical isolationBuilt-in microprocessorSwitch configurable for 0~5 V, 0~10 V or 0~20 mA outputsSwitch configurable Pt and Ni RTD input ranges
-
Product
Current Data Logger with USB VA601-A2 0-600A
VA601-A110
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Multifunction data logger with K J PT type current .voltage : K.J . PT100. PT1000. mADC. AAC. VDC.VAC.
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
Plug and Play Potentiometer Input Module
DSCUSB-PT
-
The DSCUSB-PT is a compact, high-precision potentiometer input module; converting a resistance based input (potentiometer) to a digital output. Can be used with resistance based sensors to indicate position, rotation and angle. Aimed at applications which require high accuracy. Simply by plugging the device into a PC, data can be extracted from the potentiometer input to the DSCUSB-PT for a wide range of applications. This is achieved using the DSCUSB Toolkit software, which is a simple configuration tool designed specifically for configuring DSCUSB modules. It allows configuration, calibration, logging and parameter management of the modules.
-
Product
Trace Gas Analyzer
PTR-TOF 4000
-
The new PTR-TOF 4000 is a compact, ultra-sensitive & high-resolution IONICON PTR-TOF real-time trace VOC analyzer. It is our first high-resolution PTR-TOFMS built into the same small and lightweight layout known from our successful PTR-TOF 1000 series. It also features the new hexapole ION-GUIDE technology for increased sensitivity and resolution. The PTR-TOF 4000 thus allows you to benefit from both high mass resolving power and high-sensitivity. Like the other instruments built on this platform also the PTR-TOF 4000 demonstrated its reliability and robustness but also its remarkable technical abilities and speed during various international campaigns (e.g. NASA's KORUS-AQ).
-
Product
Secondary Injection Test Set
PTE-100-C Pro
-
The values which are presented in the LCD display are highly accurate, easy to read, and independent of the injection made by the PTE-100-C base unit.The display shows continuously the phase difference between the voltage and the current injected, and can be adjusted during the test with an accuracy of 0.1º. This facilitates the test for directional relays or reclosers and synchronizing relays, etc.
-
Product
P1 Telecom Auditor
PTA
-
PTA provides network discovery, security scanning and auditing for SS7/SIGTRAN, GPRS/GTP-C, LTE/Diameter and 5G protocol stacks. PTA enables Security and Telecom Engineers to discover the security level of their networks and assess the vulnerabilities of signaling Network Elements. It also provides CIOs, CTOs & VPs of Engineering, decision makers and top management, the ability to control the evolution of their Core Networks™ security using a dashboard of key indicators.
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Product
Polarity Tester
PT5
-
PT5 Polarity Tester supporting testing of up to 24 single-mode or multimode fiber MPO or ribbon cables.
-
Product
Relay Tester
PTE-50-CE
-
The reversible 100-VA amplifier can inject up to 50A or 150V with outstanding stability, free of distortions and completely isolated from the power supply. The waveform is synthetized electronically and can generate harmonics from 1st to 7th of the supply’s frequency. Various output ranges are available to maintain the 100VA power throughout the entire settings scale. The system features automatic protections against overload and overheating.
-
Product
High Voltage DC Personal Tester
DC/PT 75
-
Within a matter of seconds you can measure for yourself whether a voltage exceeding 750V is present. Used on voltages up to 75kV DC to earth.
-
Product
MCB Test Option, Monitor Voltage Adapter
PTE-FCB
-
The PTE-FCB / PTE-FCD can be used to effectively reduce the sensitivity of the monitor input. The monitor input detects the relay’s operation and stops (or starts) the chronometer when testing with the PTE-100-C, PTE-50-CE, PTE-50-CET, and all LETs excluding the LET-400 (which lacks a chronometer).
-
Product
DC Hipot and Megohmmeter
PTS Series
-
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
Product
Relay Testing Voltage Source
PTE-FCL
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCL upgrades the PTE-100-C to the PTE-100-C Plus model.
-
Product
Three-Phase Relay Tester
PTE-50-CET
-
The equipment comprises of three independent output channels that can be selected as current or voltage. This enables the unit to be used as a complete single-phase equipment (voltage, current, and phase angle between them) or, with channels synchronised, as a three phase current or three phase voltage generator from a single phase mains input.
-
Product
Pitot Tube Flow Meter
PTFM-1000V2
-
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
Product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
-
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
Product
Gas Distribution Panels
PTS DII
-
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
Product
Trace VOC Analyzer
PTR-TOF
-
Extremely sensitive real-time PTR-TOF VOC and organic particle analyzers. The world's bestselling PTR-TOFMS series with TRU-E/N and patented ion-chemistry quality. Find the perfect match for your analytical challenge!
-
Product
Pressure Transducer Module
PTM-1000
-
Advanced Thermal Solutions, Inc.
The PTM-1000, Pressure Transducer Module, is a four-channel test instrument for measuring differential pressure in enclosures where air flow integrity is critical to proper performance. As the demand for more energy efficient cooling grows, the need for measuring the pressure at each source of heat generation will follow.
-
Product
4 & 5 Pin Trailer Circuit Tester
PT7866
-
Traces each lighting function to the terminal in question. Plugs into the trailer plug. Each LED light corresponds to the circuit being energized. Provides an easy to connect ground terminal for trailer lighting set-up.
-
Product
HD Visible and Thermal Pan/Tilt
Triton™ PT-Series HD
-
The FLIR Triton™ PT-Series HD is our most advanced dual-sensor security system, combining a cooled or uncooled 640 × 480 resolution thermal sensor, a 1080p HD visible-light imaging sensor, and a high speed, precision pan/tilt system. The Triton PT-Series HD integrates easily with FLIR United VMS 8.0, as well as other major third party video management systems, making it an extremely versatile solution for critical infrastructure protection in total darkness, bright sun, and adverse conditions.
-
Product
Sensor Six-Pack
PT-6
-
PT-6 Sensor Six-Pack - For multi-point temperature measurements. Inexpensive, Flexible. Welded sensor beads, tough kapton insulation. Diameter is .029''. Maximum temperature 350°C, Time constant 0.01 Seconds. 5 foot lead. Not isolated.
-
Product
Single Phase Relay Tester
PTE-50-CE Pro
-
This electronic, independent source can be adjusted in amplitude, frequency, and phase angle. It comes installed as standard with the ‘Pro’ versions of the PTE sets, but it can also be purchased separately and mounted by the user inside the unit’s lid in a few minutes.
