Mixed Signal Testers
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, MIxed Signal Test Systems
-
Product
Signal Stability Analyser
-
A self-contained phase/frequency analyser. Its area of use includes measurement of frequency stability and spectral purity of signal sources from 3MHz to 919MHz. Stability of amplifiers, cables, or other passive devices can be measured. Allen Variance (AV) and Power Spectral Density (PSD) graphs are automatically generated.
-
Product
Digital Signal Processor Card
CHAMP-AV4
-
Curtiss-Wright Defense Solutions
The CHAMP-AV4 is the third generation of quad NXP (formerly Freescale) Power Architecture DSP board with the QuadFlow architecture providing high bandwidth connections between four 7447A/7448 processors.
-
Product
Rub Tester and Abrasion Tester
RT4
-
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
Product
Signal Analysis
FFT Analysis
-
The program FFT (Fast Fourier Transform) Analysis is used for narrow-band spectral processing of signals coming from the input channels of ADC modules and FFT spectrum analyzers (in real-time or recorded time realization view mode), as well as for viewing various spectral characteristics of signals.
-
Product
Mixed Signal Oscilloscope
iMSO-104
-
the first mixed signal oscilloscope designed specifically for the iPhone, iPod touch, & iPad. It's intuitive and easy to use, which is why it's the preferred scope for the next generation of inventors. But don't take our word for it. Download iMSO in the App Store and test drive the interface for free.
-
Product
Service Testers
-
Service tester with receiver probe, laser pyrometer, alligator clip cable, 10 inch handle, manual and standard bag.
-
Product
Cable Testers
E447
-
Similar to E445 but without jack and RCA (phono) testing facilities. Includes special XLR remote unit to enable testing of cables where it is not possible to bring both ends to the tester.
-
-
Product
Signal Conditioner
SA420
-
Features • Works with a remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • Accepts wide range of input frequencies 0.01 Hz to 10 kHz • 4-20 mA and 0-10 VDC outputs proportional to shaft speed • Field adjustable calibration • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • DIN rail mount
-
Product
Electrical Testers
-
The Fault Trapper is a new class of tester using Spread Spectrum Time Domain Reflectometry (SSTDR) to monitor energized circuits.
-
Product
Blanking Signal Generator II
MS 1609
-
This System used for generating continuous and pulsed variable power outputs (Voltage).
-
Product
Video Signal Generator
MSPG-2000
-
MSPG-2000 Video Signal Generator, was designed to test standard Panel and Multimedia Video Signal. Separated four(4) boards generate selected own(1) Time & Pattern and output to the each section with two(2) ports.
-
Product
Torque Tester
DIS-RL series (05/2/6)
-
Tightening and final check of screws and bolts. Separate type digital torque driver/wrench. The detection part is very compact, and it is effective for torque measurement in narrow places and minute torque measurement. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Shock Testers
-
Shock test data is key information when determining if your product is capable of withstanding its intended distribution and use environment. For any mechanical shock testing application, Lansmont builds a Shock Test System to meet your needs.
-
Product
Battery Testers
EEST 50-60
-
Charge/discharge and test benches for aerospace batteriesCharge/discharge benches for the maintenance, the certification, the training and the homologation of all industrial battery types
-
Product
EMF Testers
-
Shanghai Beha Electronics Co., Ltd.
*Handy EMF tester*Digital EMF Tester for Measurement of Magnetic Field Strength*direct display in Tesla or Gauss*Measurement Range:0...199,9 μT0...1999 mG
-
-
Product
HDBaseT Tester
-
The MS-TestPro is the only HDBaseT tester that is all-inclusive, 100% reliable, portable and affordable, making it an indispensable tool for all installers and integrators. It provides AV professionals with all the information that they need while in the field to enable them to verify the integrity and stability of every system tested down to the last detail. Moreover, the MS-TestPro generates a report including all the parameters necessary to certify link quality and status up to 4K Ultra High Definition. The report can then be transferred to a computer or even to a smartphone for use by both installer and end-user.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032T
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
100MHz DDS Signal Generator
408A
-
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
Product
Insulation Testers
-
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
-
Product
PXI Bus Signal Amplifier
3222
Amplifier
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
Product
Industrial Tester
-
Ensures products, materials, or systems meet quality, safety, and performance standards by performing tests like voltage checks, mechanical stress tests, or functional simulations, using specialized equipment or manual methods to identify defects and ensure reliability in manufacturing, construction, and technology sectors, often for electrical, data, or material integrity.
-
Product
20 GHz Signal Source
VCO Series
-
The SC5510A and SC5511A are VCO-based, synthesized signal sources with very low phase noise and an amplitude control of 0.01 dB throughout its -30 dBm to +15 dBm output power range. By utilizing a unique multiple phase-locked loop architecture, phase spurs are kept below -70 dBc across the entire tuning range, even at 1 Hz step resolution. Download the data sheet to see how the impressive features and specifications of these modules make them stand out when compared to other small modular synthesizers. These 20 GHz signal sources include an additional, independent RF2 channel with a tunable frequency range from 100 MHz to 3 GHz and a tuning resolution of 25 MHz. The extra channel makes the modules suitable for either single-stage RF conversion systems or dual-stage image suppression up/down converter systems. Both modules make great general-purpose laboratory signal sources where demanding low phase noise and signal purity are required. They are both ideal choices as an integrated clock source for fast DAC and ADC applications, especially those that require variable sampling rates. Full implementation instructions, GUI, driver software, and example code are provided with each module.
-
Product
Vector Signal Generator
MGKS
-
The MGKS vector signal generator is designed to reproduce arbitrary waveforms, as well as sinusoidal signals with amplitude, frequency, phase modulation or without modulation. The generator can be used for research, tuning and testing of systems and devices used in radio electronics, automation, computing and measuring technology, instrument making.
-
Product
Automotive And Signalling Goniophotometers
-
Photometric Solutions International Pty Ltd
PSI offers a diverse range of Automotive and Signalling Goniophotometers. These operate in the CIE A/alpha coordinate system, and are used to measure and evaluate devices such as:
-
Product
Electrical Testers
-
CURT electrical testers are perfect for testing a new wiring harness on your vehicle or troubleshooting the existing wiring. Our trailer plug testers are built with LEDs and are available in 4-way, 5-way, 6-way and 7-way. We also offer brake control testers.
-
Product
Environmental Testers
-
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
