Mixed Signal ATE
See Also: Mixed Signal, Mixed Signal Oscilloscopes, Mixed-Signal Test, Mixed Signal Testers, MIxed Signal Test Systems
-
Product
Mixed Signal Tester
STI9000
-
The STI9000 is a mixed signal ATE used for testing ASIC and MEMS products. Each STI9000 test instrument fits into a small tester mainframe and contains multi-functional analog and digital test resources.
-
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781260-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Breadboard Module, 2-Slot, No Connector
40-220A-102
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
MXA Signal Analyzer, 10 Hz To 50 GHz
N9021B
Signal Analyzer
The optimum choice in wireless for 5G and other new-generation devices Evolve test needs of advanced wireless R&D and manufacturing with the widest analysis bandwidth in its class and superior phase noise performance at high frequencies See through the complexity of challenging signals with RTSA and industry-leading PathWave 89600 VSA software Simplify testing with one-button measurements from PathWave X-Series measurement applications Enable faster test time with enhanced frequency sweep algorithm and hardware-based signal processing without compromising RF performance
-
Product
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG White, Single Ended (3 Amp)
7-104924000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", TriPaddle, 24 AWG White, Single Ended (3 Amp).
-
Product
Signal, Patchcord, Receiver, 72", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
Product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 68-Pin Male SCSI
7-124883666-072
Signal Patchcord
Signal, Patchcord, Receiver, 72", QuadraPaddle, 68-Pin Male SCSI.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-121424000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White Twisted Pair, Single Ended ( 5 Amps).
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-02
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXIe-5667, 3.6 GHz PXI Vector Signal Analyzer
782366-02
Signal Module
PXIe, 3.6 GHz PXI Vector Signal Analyzer - The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. Additionally, the PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
Product
20GHz Dual Channel MW Benchtop Signal Generator
LSX2092B
Signal Generator
The LSX2092B is a 20GHz Dual Channel Microwave Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
PXIe Frequency Reference: 10 MHz And 100 MHz
M9300A
Signal Generator
The M9300A PXIe frequency reference is a PXIe-compatible, compact, modular instrument that can be used with the Keysight M9301A synthesizer, M9310A source output, and M9311A modulator to create the world’s fastest vector signal generator, the M9381A. Create a CW source, the M9380A, by combining the M9300A with the M9301A and M9310A or use it as the 10-MHz or 100-MHz reference with other PXI solutions. Control the instrument through a soft front panel and programmatic interfaces tuned to your application development environment of choice.
-
Product
Signal Patchcord, ITA, 36", QuadraPaddle, 24 AWG Black Teflon, Single Ended
7-121024000-036
Signal Patchcord
Signal Patchcord, ITA, 36", QuadraPaddle, 24 AWG Black Teflon, Single Ended.
-
Product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
Signal Module
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
Product
PXI Breadboard Module, 2-Slot, 37-Pin D-Type
40-220A-202
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
Signal Analyzer
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
Product
12GHz Single Channel Signal Generator 19" 1U Rack Module
LS1291R
Signal Generator
The LS1291R, 12GHz Single Channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. The LS1291R features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS1291R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-03
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
signal analyzer
DSA DOCSIS
Signal Analyzer
Only the highest signal quality ensures maximum throughput. The R&S®DSA DOCSIS signal analyzer has been designed to support users by ensuring the highest signal quality. DOCSIS is the standard for transmitting IP data within hybrid fiber coaxial (HFC) cable TV networks.
-
Product
PXI Breadboard Module, 1-Slot, 78-Pin D-Type
40-220A-401
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-02
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR … test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
UXA Signal Analyzer, Multi-touch, 3 Hz to 110 GHz
N9041B
Signal Analyzer
Characterize challenging millimeter-wave signals: 5G, 802.11, satellite, radarMake continuous sweeps up to 110 GHzCapture lower-level spurious signals with DANL as low as -150 dBm/Hz (> 50 GHz)Simplify analysis of the latest wideband signals: 1 GHz fully-integrated instantaneous bandwidth; 5 GHz with external IF output
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 22 AWG White XLPVC, Single Ended (5 Amps)
7-103962000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", TriPaddle, 22 AWG White XLPVC, Single Ended (5 Amps).
-
Product
Multichannel Signal Generator for DOCSIS 3.1 Downstream & Upstream
CLGD DOCSIS
Signal Generator
The R&S®CLGD is a multichannel signal generator for simulating a cable TV network with full channel loading. It generates broadband data signals for DOCSIS 3.1 as well as digital and analog TV channels. Signals can be freely combined in the downstream or upstream, allowing users to simulate any conceivable channel loading scenario in the lab.
-
Product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Single Ended (5 Amps)
7-124922000-036
Signal Patchcord
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Single Ended (5 Amps).
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783126-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
PXI Breadboard Module, 1-Slot, 20-Pin GMCT
40-220A-801
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
