Test Bench
worktable including instrumentation, fixturing and unit under test.
See Also: Test Benches
-
Product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
-
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
Product
AC Power Supply and Frequency Converter
P Series
-
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Product
Energy Meter Test Bench
GF102
-
Beijing GFUVE Electronics Co.,Ltd.
The GF102 is used to test single phase energy meter error. Adopt mature signal synthetic and power amplifier technology, high precision 500V voltage and 120A current output, accuracy 0.05%, automatically test all kinds of single phase enegy meter.
-
Product
Automated Connector Tester
-
GCI's Automated Connector Tester is a self-contained test bench providing reliable testing of filtered and non-filtered electrical connectors. The ACT automates the tedious process of testing each pin against all others and shell for DC and AC leakage. For filter connectors, the ACT accurately measures pin-to-shell capacitance. For pins protected by diodes, the ACT provides leakage and breakdown measurements. The ACT also verifies pins which are intentionally shorted to each other or to the shell.
-
Product
Axle Damping Test Bench
C_MSD C 2.5 W250 | VP 215049
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Pitot Static Indicator
ADSE 740
-
The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.
-
Product
Testing Aircraft Tachometers
-
The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.
-
Product
Meter Test Benches
TST 3/5 UNIVERSAL
-
*A Three-Phase Voltage Generator EE-500 V for voltages up to 500Vac;*Five identical Modules EE-120A, each comprising three-phase current generators from 1 mA to 120A each) and Energy Standard Class 0.04;*Meter Suspension Rack with 5 positions for hanging the meter, Scanning Heads, Electronic Readers, Tariffs, Panic Button, Lamp;*PC with EE Software for control, memorizing, search and print of Reports.
-
Product
Phase Angle Meter
597C
-
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
Product
Testing of Compressors and Compressors
-
Automatic production test bench for semi-hermetic refrigeration compressors on 2 parallel assembly lines with 3 test stations each and central database.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
ECAT Measurement Modules
-
For high-speed measurement applications exceeding the CAN bus capabilities, CSM's EtherCAT®-based MiniModules provide the optimal solution. EtherCAT® is an established protocol for fast and synchronous measurements with its roots in the test bench measurement technology sector.
-
Product
Gyro Evaluation & Test Equipment
MS 1113
-
The automatic test bench for gyros (ATP) is used to carry out the final acceptance test for the gyros in the stand-alone mode. It is a PC based test set up incorporating standard and custom built test and measuring instruments interfaced by GPIB bus. The gyros are installed on the platform, which is used to provide information pertaining to the angle at which aircraft is flying.
-
Product
Burn-In Tester
-
Universal test bench system. Provides basic electrical measurements at a low cost. Designed for a wide range of electronic products with a dedicated wiring harness. Allows you to expand the scope of functionality. Work in automatic or manual mode. Tailored to the needs of low- and high-volume production
-
Product
High-Performance Autoranging DC Power Module, 60V, 20A, 300W
N6754A
-
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
Workstation For Acoustic & Vibration Engineering
imc WAVE 2022
-
imc WAVE is a modular, powerful software platform for noise and vibration analysis (NVH analysis). From noise investigations in road tests to structural analyses on the test bench and vibration tests on machines: with different imc WAVE analyzers, you can evaluate a wide range of applications without having to be an expert yourself. In this way, you can also easily and reliably obtain standard-compliant analysis from the fields of noise and sound power analysis, structure analysis as well as the evaluation of the analysis of vibrations and of rotating machines. imc WAVE guides you step by step through the settings, from device configuration to calibration and measurement. In the end, you evaluate your data professionally and then receive a report that is ready to print. The modular software specializes in the following topics.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Hand Socket Lid
-
Hand socket lid is normally used to run evaluation tests on semiconductor devices prior to High Volume Manufacturing mode. It can also be used as a trouble shooting tool at bench test.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
Test Bench Automation & Control Software
itk.TACware
-
Automation software for the effective, time efficient and user friendly operation of component test benches. The structure and implementation of the software is specifi cally optimized for highly dynamic test benches with high demands on control quality. Inparticular, itk.TACware provides a solution for test benches of medium degree of complexity (e.g. steering test benches and suspension strut test benches), that meets all current requirements for test bench automation.
-
Product
Single Phase 2 Circuit Energy Meter Test Bench Type KP-S1000-B
-
Bofa Instrument & Equipment Co., Ltd
Single phase 2-circuit energy meter test bench type KP-S1000-B, is a new generation, high precision energy meter calibration equipment. It is especially designed for testing 2-circuit energy meter (shunt circuit and CT circuit), open or closed test link (I-P link) both. It is an ideal testing equipment for mass production of 2-circuit energy meter in meter factory. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
PC Based Comprehensive Test Setup for Luminaires
-
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
Three Phase Meter Test Bench
-
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
Product
Scienlab Emulator Control Software
SL1092A
-
The Emulator Control software can control Scienlab systems from Keysight such as the Machine Emulator and the Dynamic DC Emulator. The software also can manage both emulators combined in a test bench manually.
-
Product
Phoenix Modular Facilities
-
The lean design and unparalleled portability of Atec’s Phoenix™ Series Modular Test Cells have shifted the paradigm for engine testing. The Phoenix Cell delivers the functionality of traditional brick and mortar engine test cells with the added benefit of efficiently transported equipment. It offers our customers a flexible, low-risk, value-driven engine test cell solution for their most important equipment. The Phoenix Modular Cell is the premium solution for turboshaft, APU, and test bench applications. It can be particularly attractive where construction in certain settings may be difficult, or where usages may be short term or temporary at the location. No matter the logistics, Atec has a Phoenix™ Series Modular Enclosure to meet your needs.
-
Product
Vsync™ Controls Platform
-
Vsync™ is RedViking’s 4th generation powertrain dynamic testing software, based on over 100 fielded dynamic component test benches. Developed by RedViking for aerospace, automotive and off-highway test labs. Your lab or end-of-line test stand won’t have to rely on multiple stand-alone systems with limited data acquisition and analysis capabilities. Vsync™ provides an integrated, user-friendly platform for indisputable test data with superior repeatability and traceability.
-
Product
KWH Meter Test Bench
-
This test bench is widely used in electrical and engineering sector for varied testing applications.
-
Product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
-
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
