Fiberoptics
Field of optic fiber application.
-
Product
Fiberoptics
401/402LZ
-
Antenna Technology Communications, Inc.
The 401/402LZ is a outdoor/indoor mounted fiber optic transmitter for RF signals in the satellite L-Band or wider frequency range. It accepts a single RF input on coaxial cable and provides a single output for optical transmission. Up to four 401/402LZ’s may be installed in the ATCi Link4i chassis.
-
Product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
-
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
TDR Composite Cure Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Composite Cure Monitoring [1-4] provides a new approach to cure monitoring of advanced polymer composites. Using a high-speed pulse and inexpensive microwave sensor, our TDR system follows rotation of a polar resin molecule, providing real-time information on viscosity and percent cure. Operating in the microwave frequency range, TDR Cure Monitoring provides an alternative between high-frequency fiber-optic methods and low-frequency dielectric methods, combining optical-style precision and miniaturization with electrode-based simplicity and robustness.
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
Product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
-
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
Product
PXI Optical Switch
-
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
Product
VME Bus Repeater
VME-5532L
-
Easily link your VMEbus systems via fiber-optic cable, with total electrical isolation, no EMI generation and high-noise immunity.
-
Product
Multifunction Platform
OSICS
-
The OSICS multifunction modular platform offers the highest flexibility and largest choice of plug-ins required in fiber-optic component and system testing, particularly for DWDM system evaluations.
-
Product
S2 Unicolor Digital Sensors
ULP-S2 SCC
-
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-100
-
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
Product
8-Channel VME Delay Generator for Facility Timing Systems
V880
-
The V880 is a VME-based system timing module, used to distribute picosecond-precision timing pulses across physically distributed facilities. The V880 receives a 155.52 MHz (OC3 rate) fiberoptic master timing signal and outputs eight local triggers.
-
Product
Fast Speed Models (PCI Cameras)
xiB 64
-
High-speed interface with a bandwidth of 64 Gbit / sec. CMOSIS sensor: CMV12000. Luxima sensors: LUX13HS, LUX19HS, LUX160. Gpixel sensors: GMAX0505, GMAX3265. Resolution from 1 Mpix to 65 Mpix. Speeds from 333 Fps to 3500+ Fps. Suitable for OEM customization and Embedded vision systems. Distances up to 300m over fiber-optic cable. Compact housing: 60 x 70 x 55 mm
-
Product
Handheld Optical Power Meter
JW3402
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3402 Optical Power Meter is a highly cost-effective portable power meter and it’s newly launched by the Joinwit Company. It can be used for the optical power measurement within the wavelength 800～1700nm. JW3402 also has a wide measurement range which is more than 70dB. It’s designed with the common wavelength calibration points, such as 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm. The instrument is widely used in fiber-optic link construction, testing and maintenance.
-
Product
Fiber-Optic Transmission
-
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
Product
Multimode Fiber-Optic Transceivers
-
Schweitzer Engineering Laboratories, Inc.
Multimode fiber-optic transceivers convert EIA-232 or EIA-485 serial ports to multimode fiber-optic ports.
-
Product
Type T7 Fiber-Optic Cable for GPIB-140, 20 m
182805-020
-
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
Product
Fiber Optic Sensor Systems
-
Fraunhofer Institute for Telecommunications
Fiber-optic and photonic measuring systems open up innovative measuring and control technology concepts for a wide variety of applications. They play a major role in optimizing energy efficiency and are important technological innovation drivers for new and future-oriented markets.In the Department of Fiber Optic Sensor Systems of the Fraunhofer Heinrich Hertz Institute, the focus of application-oriented research is on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication capability as well as extremely low power consumption or even a self-sufficient power supply.In the Department of Fiber Optic Sensor Systems at the Fraunhofer Heinrich Hertz Institute is focused applied research on the development of a new generation of photonic sensors. These are characterized by extreme miniaturization, high network and communication skills as well as an extremely low power consumption, or even a self-sufficient energy supply.
-
Product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-500
-
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
Product
Universal LightProbe Sensor Six-Pack
S6P
-
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
Product
S2 Penta Sensors
ULP-S2 PCI/V
-
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption:Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Output Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: Typical response time: <10mS capture time; <100mS overall responsetime for color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
Sensing
-
Omron offers a variety of proximity, photoelectric, and fiber-optic sensors for the automotive, food and beverage, and material handling industries.
-
Product
Throwdown Fiber Transport & Converters
NanoBriX Series
-
We often forget all that happens along the media signal journey. Video and audio signals are converted, equalized and re-clocked as they move on and off fiber-optic networks. These same signals are manipulated and multiplexed as they are distributed through studio, venue and campus infrastructure on their way to headends and destination points. Audio signals are embedded and de-embedded alongside video streams, and properly mixed for varied broadcast and playout services. It’s almost too much to keep up with. MultiDyne’s NanoBrix Series assures that these many stages of the signal lifecycle are reliably addressed in one complete family. NanoBrix offers a comprehensive product line of miniature, rugged, quick-connecting throwdown solutions for temporary or permanent applications, including live TV productions, sporting venues, and broadcast facilities.
-
Product
Inertia lnavigation for Civil Engineering
-
Exail's Attitude and Heading Reference Systems (AHRS) and Inertial Navigation Systems (INS), incorporate Fiber-Optic Gyroscopes for reliable performance in civil engineering. Suited for tunneling, mining, construction, railway, and mobile mapping, these systems excel in challenging environments like GNSS-denied areas, ensuring undisturbed navigation, accurate georeferencing, and precise pointing amid obstacles such as buildings, trees, tunnels, and mines.
-
Product
Reflective Memory PCIE card
PCIE-5565PIORC
-
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
Pump Combiners
-
Pump combiners, also called pump couplers, are special application fiberoptic couplers used for sending pump and signal light into an amplifier or laser fiber. Because of these applications, pump combiners are specially designed for high-power use.
-
Product
S2 Spectra Sensors
ULP-S2 WBI/V
-
The ULP S2 Spectra Sensor tests for LED intensity, and for any color in the visual spectrum, plus white. The S2 Spectra Sensor is well-suited for the test of “boundary” color LEDs, as it can unambiguously and repeatedly distinguish between not only adjacent visual colors such as green and yellow, but it can determine different hues of the same color such as yellow and amber, regardless of LED intensity. Implemented in a unique and customizable 2-Part solution, the S2 Spectra Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Output Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response time: Typical response time: <10mS capture time; <100mS overall response timefor color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
Product
Highly Accelerated Stress Test Chambers
HAST
-
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
Product
(≤ 3.0GHz) DFB Light Source (ITU-T)
DFBL-0300
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DFBL-0300 series is a set of high linearity DFB CW Light Source for modulation bandwidth <3GHz, mainly applied to optical accessory and fiber-optic communication equipment testing, modulation bandwidth <3GHz simulation, digital signal transmission R&D and application.
