CT
1) Current Transformer 2) Computed Tomography
-
Product
Continuous Gas Analyzer
CT5400
-
Multi-component continuous gas analyzer combines QCL and TDL technologies in a single rack mount enclosure to measure process gas and monitor emissions from sub ppm to % levels. The CT5400 is ideal for measuring NOx, SO2, CO, CO2, CH 4, NH3, O2, HCl and other combustion gases identified as pollutants, ozone depleting, or responsible for global warming.
-
Product
Digital Circuit Breaker Analyzer
CT-7000 S3
-
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
Product
Current Measurements of PWM or Inverter, AC/DC 25～500A, φ35mm
CTF-500DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 25～500A*Current measurements for PWM or inverter
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
Current Measurements of PWM or Inverter, AC/DC 1～50A, φ16mm
CTF-50DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
Product
Motor Performance Tester
CT Series
-
Shanghai Aoboor Electric Co., Ltd.
Test the cogging torque of motors, separate motor cogging torque and friction torque accurately; cogging torque test results is independent of test speed and speed fluctuation.
-
Product
Through Hole type AC Current Sensor
CT-6K
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Current Measurements of PWM or Inverter, AC/DC 10～200A, φ24mm
CTF-200DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
Product
Compression Tester
CT66K
-
Tests compression on all domestic and imported cars and trucks with gasoline engines. Side release valve allows quick re-testing of cylinder without removing the tester or adapter. Large 2-1/2" gauge with dual inch/metric readings: 0-300psi and 0 to 21 kg/cm2.
-
Product
Cryocoolers
DS Mini
-
The DS Mini cryocooler brings gas bearing technology to the mini-cryocooler market. The DS (Dual Split) features dual-opposed pressure wave generator pistons and a split cold head to reduce exported vibration and acoustic noise. The optional passive balancer will further reduce cold head vibration for sensitive applications. Both the cold head and wave generator can be mounted in any orientation. Using gas bearings in the pistons as well as the displacer, the DS maintains the core technologies of the well-established integral CryoTel MT, CT and GT cryocoolers. The DS Mini represents an advantage over flexure bearings due to its higher power density, while still offering a longer lifetime compared to rotary compressors and contact seals.
-
Product
Through Hole Type AC Current Sensor
CT-13K
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*High accuracy and compact size.*Measuring range:AC 1A～50A.
-
Product
Through Hole type AC Current Sensor
CT-6S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Autorange Digital Multimeter
CT8017
-
State of the Art ergonomic design and styling for easier handling and use. Full Auto Ranging range selection. Manual range selection function. Large 3 digit LCD display with analog bar graph. AC/DC Voltage measurement up to 600 Volt. Manual or automatic VDC/VAC selection. DC Current measurement up to 10 A. Resistance measurement up to 32 MOhm
-
Product
CTE Tester
CTE-360
-
The CTE-360 measures thermal expansion coefficients on wide range of materials over a temperature range of -20°C to 100°C. Although intended primarily for the study of materials used in electronic packaging applications, it can be used on virtually any solid, gel, paste, or viscous liquid over this temperature range.
-
Product
Handheld Optical Fiber Identifier
JW3306C/CT
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3306C Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification work, can be detect in any location of both SM and MM fiber. Meanwhile when you combined with JW3306CT Optical Signal Generator, which can realize low-frequency signal online injection, and also realize to find a particular fiber online without modulation signal in optical fiber signal .
-
Product
Standard CT
3200A
-
• High accuracy of 3200/5A (0.005%) • multiple ratios • Various Current ratings
-
Product
Lithium Battery Equalization Tester
LIFG-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
LIFG-CT series tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem of inconsistent voltage of lithium battery pack.
-
Product
Crimp Tool For MS-M Style RF Connector Pin
40-969-501-CT
-
This Crimp tool allows RF connections to be made to RG178 co-axial cable and the corresponding MS-M style housing 40-969-526-F.
-
Product
Opacimeter on CONNECT Trolley for Measurement of Diesel Vehicles
MO CT | VP 135045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter on CONNECT trolley is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
DC Energy Meter
-
Multiple channels can be measured by a single meter, EN2450N & EN2450D. Differential current input for all the current channels. Programmable shunt secondary 50mV to 100mV. Programmable CT Primary for all channels up to 200A - for Hall Effect CT. Data logging for parameters such as Energy, Load hours and Ampere hours. Easy installation,Compact size, weight and simple wiring.
-
Product
Contunuity Tester With Audio Warning
CT-01
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
Product
CLAMP ON CTS
P50
-
Beijing GFUVE Electronics Co.,Ltd.
The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.
-
Product
Current Transformer Analyzer
CT Analyzer
-
Current transformer testing in a multifunctional instrument performing excitation, ratio, polarity and winding resistance tests on current transformers as well as burden impedance measurement.
-
Product
Logger version conductivity and temperature sensor
INFINITY-CT A7CT-USB
-
Infinity-CT is an autonomously deployable data logger for temperature and salinity measurements. The conductivity sensor has a design of 7-electrode. The small-sized instrument (Φ54mm x 255mm, 0.7kg in air) can be deployed and integrated virtually anywhere. The instrument has two depth rating versions: shallow water (200m, A7CT2-USB) and deep water (2,000m, A7CT-USB).
-
Product
Active FET Probe Kit 1.2 GHz, 10x, ±40 V
CT4121
-
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design.
-
Product
ACP Portable Electrical Current Transformer Test,CT/PT Analyzer
-
Chongqing Assen Power Equipment Co., Ltd
ACP portable Current transformer analyzer is mainly used for field or lab testing, it can finish the measurements (M) and protection (P) class CT, PT and TYP class CT. Adopt 7 inch touch TFT LCD, self-equipped mini type printer supporting field printing; supporting to use USB flash disk to dump data. The CT PT Analyzer is the most complete and easy-to-use testing system for protection and metering CTs according to IEEE and IEC standards.
-
Product
Through Hole type AC Current Sensor
CT-30AR
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring electric power (through hole type)
-
Product
Converter
CTD-2160
-
The STD-2160 converter is a device for continuous monitoring and protection of rotary equipment. STD-2160 measures, controls and records signals from sensors continuously through 16 channels.
-
Product
Digit Manual Range Digital Multimeter
CT8015
-
State of the Art ergonomic design and styling for easier handling and use. Full control manual range selection. Large 3 digit LCD display. AC/DC Voltage measurement up to 600 Volt
-
Product
GAOTek Three-Channel Leakage Current Tester
GT00YB00ZV
-
The GAOTek Three-Channel Leakage Current Tester provides online measurement, monitoring, and recording of three channel AC leakage currents simultaneously by adopting the latest CT and magnetic shielding technology. This instrument provides highly accurate and reliable measurements. Additionally, it can locate insulation faults and repair electrical lines. It is composed of a special alloy and consists of a test monitoring software, current clamp, and communication cable. The instrument can store 3900 sets of data and enables online and real time monitoring, historical data inquiry, read, inquire storage, generation, and printing of a fitting curve. It is widely used in 380/220 power systems. It complies with IEC1010-1, IEC1010-2-032, Pollution Class 2, CAT Ⅲ (600 V), and IEC61326 (EMC standard) safety codes.
