RF Matrices
route radio frequency signals through a a grid array.
-
Product
MS-M RF Connector Pins RG178
40-969-501-FC
-
This is a 30 piece kit of RF Connector Pins for MS-M Connector Housing, suitable for RG178 Co-axial Cable.
-
Product
MS-M RF Cables for Pickering Products
-
The cable assemblies below are suitable to use with Pickering cards and modules that utilize a MS-M RF connector.
-
Product
Open-Short-Load RF calibration kits
-
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, SMB
40-870A-003
Relay
The 40-870A-003 (PXI) and 42-870A-003 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
Product
RF Connectors
SMP Connectors
-
The SMP interface is a subminiature interface in the same scale as MMCX connectors but offers a frequency range of DC to 40 GHz. It is commonly used in miniaturized high frequency coaxial modules and is offered in both push-on and snap-on mating styles.
-
Product
RF Synthesizers
HS9000 Series
-
Holzworth Instrumentation, Inc.
The Holzworth HS9000 Seriesmulti-channel platform is designed to achieve optimal channel-tochannel stability across all integrated channel synthiesizers via a conductively cooled, fan-less enclosure. Specific attention is paid to phase coherency between the independely controllable channels.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
RF Power Meter
4240
-
The 4240 series of CW RF power meters provides the high speed measurement capability needed in a production environment, as well as the simplicity of operation required for bench top use.
-
Product
RF Explorer Spectrum Analyzers
-
With so many different RF application fields, budget ranges and specific needs, it is an art to design the best possible match for everyone's needs with best quality and limited cost. We are delighted to offer a broad product range of tools, adjusted over more than 10 years of team dedicated R&D, careful listening to customer needs and feedback, and strong research on the latest technologies.Listed below you can find our current offering for RF Explorer models, including Spectrum Analyzers, Signal Generators, Expansion and IoT Modules and accessories.
-
Product
PXI 12x8 RF Matrix 250MHz 75 SMB - With Loop-Thru
40-726A-751-L
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Handheld RF Spectrum Analyser
HSA-Q1
-
The HSA-Q1 is a fully integrated portable RF Spectrum Analyser designed specifically for professional countermeasures use. With a frequency range of 0 to 13.4 GHz and sweep time of just half a second, it offers unprecented performance in a truly handheld package.
-
Product
RF Waveguide Load
-
RF Lambda’s waveguide loads are used at end of an RF signal chain to provide a good 50ohm match and dissipate any RF energy into heat. They are available in a variety of power levels and offer low VSWR.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 75Ω, MCX
40-832A-102
Multiplexer Module
The 40-832A-102 (PXI) and 42-832A-102 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Wideband RF Record & Playback for GNSS
RP-6500
-
The RP-6500 both records and plays back up to 500MHz of RF spectrum—from 9 kHz to 6 GHz—as well as simulate all common GNSS signals (BeiDou, Galileo, GLONASS, GPS, and QZSS). The system can also generate Satellite communications signals (DVB-S and DVB-S2), making the RP-6500 the ideal platform to cover all your needs, present and future.
-
Product
FieldFox Handheld RF Analyzer, Up To 10 GHz
N9912C
-
Select from cable and antenna analyzer (CAT), Vector Network Analyzer (VNA), and/or Spectrum Analyzer with desired maximum frequency. Capture elusive signals with up to 40 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
RF Subsystems
-
Using the Ideal Switch to develop RF subsystems enables substantial performance and reliability improvements. At the same time their size and weight decrease by several orders of magnitude.
-
Product
Wattchman RF Station Monitor/Alarm Systems
81070 Series
-
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
Test Instrument
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
RF Shielded Test Enclosure
JRE 0814
-
Testing tall devices? The 0814 stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure finds wide use in the WiFi test environment. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
RF Reference Sources
-
The 27 GHz 96270A and 4 GHz 96040A Low Phase Noise Reference Sources are designed specifically for RF calibration, featuring a calibration-oriented interface, precision signal level and attenuation, high signal purity and precision low distortion modulation. Both instruments simplify the process of RF calibration by reducing the amount of equipment and simplifying the calculations required.
-
Product
RF & Microwave Power Meters
-
Our RF & microwave power sensors ensure precise and reliable measurements. They provide the highest measurement accuracy and speed, simple operation, technological leadership in thermal, diode and OTA core measurement elements as well as traceability to national standards.
-
Product
PXI Single RF Attenuator, 2.3GHz
41-181-021
Attenuator
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
RF & Microwave Modules for 34980A
-
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
Product
RF Power Monitors
-
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
Product
RF Shielded Box
LTL A4001
-
Liveon Technolabs LTL A4001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A4001 RF shielded test enclosure can comfortably house the intermediate device on test. LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
RF Connectors
BNC Connectors
-
BNC connector types feature a bayonet style coupling mechanism that allows for quick connect and disconnect with positive locking. Mating is achieved with just a quarter-turn of the coupling nut. With a classic, dependable design, BNC RF connectors are suited to accommodate a large variety of RG and industry-standard coaxial cables, in a variety of termination styles.
-
Product
75 Ohm Mini SMB Cable Assembly
40-977-751-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Shield Box
-
Qosmotec Software Solutions GmbH
Qosmotec RF Guard is a RF shield box that allows engineers to create an affordable automated end-to-end test environment with each UE shielded individually. It enables the user to perform wireless network tests without undesired RF interference by protecting mobile devices from outside network frequencies.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, SMB
40-875A-001
Multiplexer Module
The 40-875A-001 (PXI) and 42-875A-001 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
