Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
Stationman Speaker Probe
250 SSP
-
This probe is designed for those technicians that want the best tool available. The Model 250SSP is supplied with a cone-shaped tip and a duckbill tip that is longer and flatter, permitting insertion into larger cables, or cables under tension where slack cannot be obtained. Another feature is the built in speaker for audio without the need for a butt set or headset. The speaker is operated by a slide switch that has a "lock" position for continuous monitoring.
-
Product
DC - 400 MHz PC-Based Timer Interval Analyzer
-
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
Product
C/I Clamp Meters
CLAMPMETER, 400A AC (CM-410)
-
*Measures to 600 volts AC and DC, and 400 amps AC*Data hold to capture important readings*Audible continuity test*Auto power off for longer battery life*Accessories included: (2) 1.5V AAA batteries, test leads, carrying case*Lifetime Limited Warranty
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
Power Monitors - AC / DC Monitors
-
DARE has a complete line of AC or DC operated power monitors available in numerous package styles including 50 Hz, 60 Hz, and 400 Hz models. In addition, DARE has a series of external aircraft power monitors that continuously monitor the quality of electrical power in aircraft electrical systems, ground power equipment, auxiliary power units (APU?s), and other equipment for pre-determined over / under voltage conditions, over / under frequency conditions, loss of phase, improper phase sequence or phase rotation.
-
Product
PXI Solid-State SPST Switch, 6-Channel 25A 100V
40-184-001
SPST Switch
This range of PXI high power switches support 6-off high current SPST switches into two PXI slots or 3-off high current SPST switches into one PXI slot. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each PXI solid-state SPST switch can support 25A of continuous current and switch up to 100V signals. The switch can sustain inrush currents of up to 90A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Working Standard Shunts
CSW
-
CSW shunts are rated to 100 % continuous current with no loss of accuracy. They are largely immune from connection errors common to many shunts. All CSW shunts include ISO17025 accredited calibration through full current range.
-
Product
Circuit Monitor
CM, CMD
-
*Continuous monitoring of trip coil continuity*LED indication of open trip circuits*N.O. or N.C. contact for remote indication of open trip coils.*Self-monitoring — long-life*Can also be used as a self-latching, high speed target for trip indication*UL Recognized*RoHS Compliant (Directive 2002/95/EC)
-
Product
AC / DC Current Probe, 10 MHz, 150 Arms
N2781B
Oscilloscope Probe
The N2781B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 150 Arms continuous
-
Product
UI Test Tool for Web, Java, Windows, Android & iOS
QF-Test
-
QF-Test is the established tool for professional GUI test automation of desktop, web & mobile applications as well as PDF documents. QF-Test is a low-code GUI test tool that allows you to efficiently create test cases, e.g. using Capture/Replay, without any programming knowledge across platforms on Windows, Linux and macOS. For software developers, Jython, Groovy or JavaScript offer advanced scripting possibilities. Tests can be run automatically via continuous integration tools such as Jenkins and generate detailed log files and XML or HTML reports. Use QF-Test to create robust and stable regression tests for various GUI technologies. QF-Test supports all types of Java GUIs, ranging from Swing (including ULC, JIDE components, CaptainCasa), its successor JavaFX, as well as the Standard Widget Toolkit (SWT) and Eclipse, including plugins and RCP applications. You can also use QF-Test to test dynamic web applications based on Angular, React or Vue.js, for example, including Electron and hybrid applications using JxBrowser, JPro or WebSwing, for example. QF-Test supports native Windows desktop applications created with Win32, .Net, Windows Forms, WPF, Windows Apps. Mobile applications can be tested on real devices or with the Android Studio Emulator or iOS Simulator and Xcode.In addition, you can test automated whether your web application complies with common accessibility standards in just a few simple steps. PDF documents can also be conveniently tested automatically with QF-Test. On the market since 2001, the test tool is continuously being actively developed and is currently used by more than 1,500 companies across 60 countries. Contact us by e-mail at service@qftest.com or get a free trial version at www.qftest.com/en!
-
Product
Signal, Contact, Receiver, TriPaddle, 5 Amp, .025" Round Post
610110179
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
Product
Multi-Network Cable Tester
3PK-NT007N
-
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Product
Visual Fault Locator
TW3105
-
Techwin(China) Industry Co., Ltd
Pen Type is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network.
-
Product
AC / DC Current Probe, 100 MHz, 30 Arms
N2783B
Oscilloscope Probe
The N2783B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785161-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
Ultrasonic Flaw Detector
MFD550B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD550B can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it show the defect clearly under the dim light and strong sunlight environment. 0-9999mm measuring range can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium ion battery module，it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways inone body, customers with different habits can operate it freely. With comprehensive performance self-checking function, it can automatically generate test reports and support for many languages. With high cost performance, it is the smart choice for the practical economic model of ultrasonic testingequipment.
-
Product
SATA (Serial ATA)
-
Serial ATA (SATA) is a data transfer technology designed to move data to and from storage devices such as disk drives, ATAPI drives, host bus adapters (HBA), and port multipliers. SATA is a serialized enhancement and replacement to parallel IDE. Since SATA ratification in 2003 and its move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with its industry leading protocol analysis and traffic generation capabilities.
-
Product
4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) With Eye Checker
RB3004
-
*Low cost continuous 4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
Walk in Chamber for Sand Dust-proof Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in dust-proof test chamber provide a simulated sand blowing and dusting environment. It can continuous operation for a long time without failure.
-
Product
Halogen Moisture Analyzer
LD-LHMA-A13
-
Halogen moisture analyzerLD-LHMA-A13with benchtop design, user can manually open the door of heating chamber for analysis. Incorporated with halogen heating lamp for rapid and uniform heating, it determines the moisture content and dry weight of the test sample. It continuously measures and immediately display the loss of moisture and weight on backlight LCD screen during test.
-
Product
120-600V Solenoid Voltage And Continuity Tester
1865
-
Peaceful Thriving Enterprise Co Ltd
This solenoid voltage tester has multiple functions. It tests for voltage, continuity and polarity.
-
Product
Condec Pressure Instrumentation
-
The Condec brand has stood the test of time with popular and dependable models of pressure instrumentation that continue to be in high demand.
-
Product
Mobile Retroreflectometer
Laserlux® G7
-
The Laserlux® G7 is the safe, smart and simple solution to meet this challenge. The Laserlux® G7 provides continuous pavement marking assessment and evaluation within the flow of traffic. It is the only commercially available instrument that does not require a dedicated vehicle or vehicle modifications to operate. Not only does the Laserlux® G7 measure pavement marking retroreflectivity, but it is able to provide additional key metrics like stripe width, location on the road, coverage, and presence, performance and location of raised retroreflective pavement markers (RPM’s, cateyes, road studs).
-
Product
Continuous Magnetic Measurement Equipment
CWM
-
The automatic measurement equipment to continuously measure magnetic property in commercial power frequency of magnetic steel sheet sample on line, is used for quality control. Core loss in definite time of magnetic flux density [B] or magnetic flux density [B] in definite time of strength of magnetic field [H] for excited magnetic steel sheet is measured on line.
-
Product
Cable Continuity Tester, DB9, RS232 Mini, Network, 21.01 mm, 35 mm, 45.01 mm
72-9200
-
The 72-9200 is a Mini Cable Tester with USB Power Cable and Battery. Quickly test DB-9/RS-232 cables. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini cable tester fits easily in your pocket or tool box and requires no external power. Confirms conductor continuity with sequential LED's. Save time and money by diagnosing connectivity issues.
-
Product
Test Charts
iQ charts
-
Image Engineering GmbH & Co. KG
The basis of our test chart portfolio are the ESSER TEST CHARTS owned by Image Engineering and known worldwide for their high quality which we continually improve. Included in the extensive program are HDTV charts for broadcast, multipurpose charts as well as the UTT chart (Universal Test Target), the leading system for the standardized digitalization of archives, which is already being used by the Metropolitan Museum in New York.
-
Product
Terminal Power Meter
TPM-50A
-
ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm；(3) Modulation bandwidth: 5MHz；(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.
-
Product
Handheld Digital Multimeter, 3 ½ Digit, Basic
U1231A
Digital Multimeter
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode and continuity visual/audio alerts. Keysight Remote Link Solution enabled.
