Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
product
Sampling Scope Adapter
N5477A
The N5477A sampling scope adapter makes the InfiniiMax III probing system fully compatible with the Infiniium 86100 DCA sampling scope family. With the N5477A, the DCA modules have 30 GHz of probing, increasing their performance and flexibility.
-
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
TAP Adapter for Corelis JTAG Controllers
Low Voltage Adapter
High technology, energy efficient, and small form factor products push JTAG interfaces to the limits; low power and high performance means low voltage, high speed, and high drive requirements. Building specialized interface circuits on product Printed Circuit Boards (PCBs) is inconvenient and costly—an out-of-the-box, external solution is needed.The Corelis Low Voltage adapter is an add-on accessory that provides existing scan controllers with an active, plug-in interface to access low voltage scan chains, without sacrificing performance.
-
product
XMC-PCIeStor, High Speed PCIe Single SSD Adapter
9301
The 9301 is a VITA 42.3 XMC adapter card / mezzanine storage module with a single M.2 SSD site. The M.2 site supports up to 4 lanes of PCIe Gen 2 connectivity at 5 Gb/s per lane when a Gen 2 or 3 capable M.2 PCIe card is used.
-
product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Isolated Serial Interface Card
PCI-ICM-2S
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
Genrad 2270 Interface Receivers
GR Series
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112772
Adapter Plate, 9050 Enclosure to 9025 ITA (ITA Positioned on Upper Part of L-Shaped Enclosure)
-
product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
-
product
Osprey ISA Unibus Adapter
9476-U-B
Unibus Controller board is EISA/ISA bus compatible and occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
product
Pneumatic Test Adapter
Pneumatic test adapters from INGUN are particularly suitable for contacting medium-sized electronic assemblies (series testing) and a large number of variants. The test adapters are designed as a replacement kit system, are connected to an existing test system and operated with replacement kits that are specially designed for the electronic assembly to be tested.
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
30 GHz differential probe with ProAxial interface
DH30-PX
30 GHz differential probe with ProAxial interface.
-
product
Real Time Monitor Interface
ANALYSIS 4N
It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.
-
product
MVTec Interfaces
If you cannot find a suitable interface for your device, you can use a template for the integration and download it here. Simply select "Templates" in the "Category" selection field.
-
product
Digitizer Adapter Module For FlexRIO
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
product
VME Controller With USB-2 Interface
VM-USB
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Test adapter LRP-LR (Type D, 4 mm)
MA-LPL02D
Hachmann Innovative Elektronik
Our test adapter MA-LPL02D connects LR measuring devices to standardized LRP string parts and capacitive test points. An insulating tube with great dielectric strength shields the user from static energized test points without automatic earthing.
-
product
Shotgun Adapter
ADP-278A
Standard Electric Works Co., Ltd
Shotgun Adapter. Material : Aluminum alloy. Dimension : 78.6(L) × 44.5(W) ×44.5(D) mm. Weight : Approx. 86.5g. Accessor for Hot Sticks and High Voltage Detectors.
-
product
Human Machine Interface
Panasonic Automotive & Industrial Systems Europe GmbH
combines state-of-the-art features and top performance with an outstanding design in an all-metal housing. The range consists of four models in sizes from 4.3", 7", 10.4" and 13.4" TFT color display with LED backlight. All models can be installed in a horizontal or vertical position. The touch terminals are equipped with an Ethernet port and support VNC technology, allowing both remote VNC applications and remote assistance. The HM500 series is programmed with the HMWin software, a simple and intuitive program, yet equipped with advanced features. It is possible to import variables from Control FPWIN Pro, the programming software for Panasonic PLCs, thereby facilitating the synergy between PLCs and HMIs. The products have a 5 year warranty.
-
product
GPIB Interface Card
PI-31000
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
product
Ethernet-GPIB-USB to Serial Interface
Model 9006
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
-
product
Tap Adapter
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
product
PCB Adapters - TriPaddle
TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
product
Handler/Prober Interfaces
IFXX
FETtest offers a variety of Interface options, which expand test capability and provide connection to other production line resources. These interfaces range in complexity from simple handler/prober interfaces to interfaces with user programmable external component connections, to capacitance measurement systems. Models are available to work with the full range of FETtest systems and Remote Stations.
