-
product
PNA-X Microwave Network Analyzer
N5241A
Reach for unrivaled excellence in your measurements and designs Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the worlds widest range of single-connection measurement applications Test linear and nonlinear device characterization more accurately with the world's best PNA-X Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Function Test Fixtures
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
product
Serial-to-Daq Minibox
Model 2367
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
product
Winding Resistance Meter 50Amps, 3 Channels Rack
WR50-13R
Raytech Digital Winding Resistance meter WR50-13R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
product
Rackmount Kit For 34980A
Y1130A
The Y1130A is used for forward or reverse rack mount. A rail kit is also required. For Keysight racks, order either a E3663AC rail kit for forward mount or a E3664AC rail kit for reverse mount. For non-Keysight racks, use a third party rail kit.
-
product
PCI Digital I/O Cards
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
product
Custom PCB Test Fixtures
Emergent Electro-Mechanical designs and manufactures customized test fixtures and burn-in racks. Each of our custom designs is unique to our customer's particular project requirements. Emergent fixtures feature innovative design components including a linear collapsing system, interchangeable and reusable plate design, and top and bottom probing.
-
product
ATE System Power Supplies
N8700 Series
The Keysight N8700 Series ATE system power supply delivers high current with low noise in a compact two unit package. Airflow moves front to back, so no additional space is required above or below the power supply in your automated test equipment (ATE) rack. This series of programmable power supplies sources up to 3300 or 5200 W. Get output voltages from 8 to 600 V and 5.5 to 400 A.
-
product
2U Rackmount Chassis with 1U ATX Power Supply
cPCIS-6230R/ 6240R Series
The cPCIS-6230R and cPCIS-6240R Series sub-systems are designed for 6U cPCI boards with 80mm RTMs and are suitable for computer telephony applications. The chassis is 2U height and standard 19" rack mount width.
-
product
GPS synchronized NTP Server
NTV-100
Brandywine Communications NTV-100RG is an affordable, convenient and flexible NTP Server. This network time server accurately time synchronizes computers, time displays, PBX’s, and a wide variety of other equipment. The NTV-100RG is a small, rack mounted NTP Server that can synchronize to GPS or to the IRIG B time code to provide NTP time.
-
product
RACK SYSTEMS
Most of ETL's sub-systems are designed to fit standard 19" racks. We produce RF distribution equipment for a wide range of applications in the RF chain. On satellite downlinks this is between the LNB and the modem or receiver; and on satellite uplinks it is between a modem and a BUC.Reliability, Resilience and RF performance are designed into all our equipment wherever possible. Scaleability and Adaptability also influence the design process.The main product families are shown below, with further selection of products via functionality and design.
-
product
HF Amplifier
bsw TestSystems & Consulting AG
Whether a HF amplifier which is mounted in a 19" rack is viewed as an instrument, a system or a component largely depends on the point of view of the application developer. We list this product family here; however we would like to point out that our 19" amplifiers for rack-mount and benchtop applications, as well as modules without power supply, are listed in the "Components" section.
-
product
12GHz 16-Channel Signal Generator 19" 3U Rack Module
LS12916R
The LS12916R, 12GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS12916R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS12916R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
product
Metered Power with Audible Alarm (14) 5-15R 1U/0U V/H
EPS-1415-HVA
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
GPS Time and Frequency Standards
Our range of GPS disciplined Rubidium Oscillator, OCXO and TCXO, low cost and stable, time and frequency references in a variety of rack mount and desktop sizes to suit all applications. For a technical discussion of GPS go here or select a link below for product information.
-
product
Rack Extender Kit, G12x, 1.5" Deep
310113519
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12x Receivers.
-
product
Rack Systems
Real-time testing and validation often require versatile testing platforms, providing a high number of different signals ranging from low-power communication and sensor signals to high-power actuator signals. Integrating all the necessary components in one standard system and designing signal-conditioning for all interfaces is time-consuming and requires specific expertise.
-
product
304/1 Vector Network Analyzer Rack Mount Kit
This rack mount kit is for the Planar 304/1. It includes track slides and handles for the full size USB VNA.
-
product
i1
VPC's one-module solution is ideal for small connector needs. Following the success of VPC’s popular rack and panel connector iCon, i1 was developed to satisfy the need for an even smaller connector. i1 holds a single iCon module in each connector, making it the perfect solution for low I/O applications.
-
product
Rackmount Kit
DAQA190A
Use this rack flange and filler panel with only one instrument mounted on either the left or the right side of the rack
-
product
S6 Rack Mount
The S6 Rack Mount receiver is ideal for consolidating multiple test instruments and only occupies 1U of rack space. This low-profile makes it ideal for in-line test applications. The S6 receiver will support an ITA/fixture weight of 50 lbs. at 6”.
-
product
Rack Mount Osprey Chassis 4-Slot Unibus
0249-U
10.5" high by 19" wide by 20" deep (267 x 483 x 508 mm), this chassis is FCC certifiable**. AT style motherboard, 3 x 5-1/4" bays, 2 x 3-1/2" bays. Cooling fans and space are included for user's hex-height, 4-slot DD-11 Unibus backplane, PC motherboard, diskette and hard drives (one hidden and four visible half-height bays).
-
product
Automated Leakage Current Tester
LINECHEK® II Series
Our LINECHEK II Leakage Current Tester is designed for medical device manufacturers. With a feature set built around maximizing the efficiency of the Leakage Current test, LINECHEK II satisfies medical application requirements demanding up to 40 Amps of continuous line current. Use it on the bench or in a rack, from the front panel or via a PC interface to ensure your medical device is ready for global deployment.
-
product
Ethernet to Relay Minibox™
Model 8064
* Model 8064-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.*Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 8064s.* Optional terminal board and terminal strip for easy connections without soldering. See the Ethernet Accessory page.
-
product
Contact Resistance Measurement System
CRMS
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
product
Vertical Hinged Mounting Frame, G18, 9U
310113328
The G18 9U Vertical Hinged Mounting Frame accommodates an 18 module receiver in a PXI chassis within a rack. This is designed for exclusive use with a VPC G18 receiver #310 120 101.
-
product
Receiver, 9025, 25 Module, for Slide Mounting
310104437
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. It is equipped with a locking handle to ensure proper ITA engagement. An included integrated microswitch shuts off power when the ITA disengages from the receiver. This receiver is designed to work with a slide kit, includes mounting flanges and an instrument bracket. A slide kit is required, but not included.
-
product
Multiple Channel Burn In Power Supply
MCPS
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
product
Receiver, G12, 12 Module, 20" Platform, w/ Extended Handle, for Slide Mount
310104416
Receiver, G12, 12 Module, 20" Platform, w/ Extended Handle, for Slide Mount (slide kit required)This G12 includes an extended handle to provide extra clearance for operation. This part number includes: G12 Receiver (w/ ext. handle) 20" Platform Left side Microswitch Mounting brackets (attach platform to slides)*Please note: Consult user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
S6, Receiver, 15" Platform Kit
310113435
The 15" platform kit easily mounts to the S6 rack mount receiver part #310122100 (purchased separately).
