Filter Results By:
Products
Applications
Manufacturers
Shielding
Protects against or confines electromagnetic or ionizing radiation.
See Also: Shielding Effectiveness
-
product
USB 3.0 Type A (With Shielding) Test Connector
Test connector for USB 3.0 Type A with shielding (9 pole) for contacting USB interfaces. Application in high-speed USB devices like hard disks, data carriers, power supplies, etc.
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
2U Family of Programmable AC-DC Switching Power Supplies to 1400W
The 2U family of programmable AC-DC power supplies sets a new standard for flexible and reliable power for your application. Available in a Rack Mounting or Benchtop at 1400W power levels with single output voltages ranging from 10 to 270V and current capabilities up to 120A. A user-friendly front panel provides reliable linear controls for finer adjustment and digital LED voltage and current meters. Standard features include; 'soft start' operation and 'no load' operation, thermostatically speed controlled fans to limit acoustic noise, short circuit and overload protection, thermal protection, internal EMI filtering, RFI shielding and remote sensing.
-
product
Chassis
Infrastructure housing for instrument cards typically containing a power supply, cooling fans and emi shielding.
-
product
Faraday Cage
Electrostatic noise from the laboratory environment disturbs measurement signals and decreases data quality drastically for small current signals. Our Faraday Cage enables effective shielding for measurement on high impedance or low current samples.
-
product
3D Electromagnetic Simulation Software
Efield® offers a complete and unique integrated modelling and simulation environment for 3D analysis of a wide range of electromagnetic applications such as: Antenna design All kind of antennas including horn, reflector, wire and microstrip antennas as well as broadband antennas and antenna arrays. Antenna integration Radiation pattern of installed antennas on large platforms such as aircraft or ships. Coupling between installed antennas. Microwave design Typical applications includes design of filters, connectors and couplers. EMI/EMC interaction Analysis of a wide range of EMC/EMI problems including shielding and coupling. Scattering & radar cross-section RCS analysis of structures such as aircraft, ships, air-intakes, exhausts, and antennas.
-
product
Isolation Transformers
Osborne’s Isolation Transformers are used to step-up, step-down and isolate voltages in single phase circuits. Isolation may be used to provide output circuit immunity from voltage spikes and noise (both common-mode and transverse-mode) present on the input system. The isolation can allow separate grounds on both the input and output sides of the transformer. Osborne also designs with a range of electrostatic shielding to provide several levels of noise immunity.
-
product
Networking lan Cable Tester
LK-468A
Test Function for cale with RJ11,RJ12 RJ45&BNC plugs.Tests continuity, assignments, paring and shielding line/voltage detection main device.
-
product
RF Shielded Box
LTL A6001
LTL A6001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A6001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
Coaxial
Adapters for converting banana jacks or single-conductor test instruments to coaxial configuration for added shielding protection.
-
product
HOT CELLS
Precisely engineered and constructed for continuous dependable protection and reliable everyday laboratory use. These cells come standard with shielding for the ionization chamber and utility connections.
-
product
1.4W to 3W - Single Output
CHVM Series
*Compact Footprint / Low Profile*11-13, 10.8-13.2, 10.8-16.5 Vdc Inputs*Programmable 0-±2000 Vdc Output*Five-sided shielding*Remote adjustment*Reduced Radiated and Conducted Noise*Less External Filtering Required
-
product
USB-Mini Type B (Extended With Shielding) Test Connector
Test connector for Mini USB type B extended with shielding (5 pole) for contacting Mini USB Interfaces. Application in smaller Mini-USB devices like cameras, mobile phones, radios, hard disks etc. Comes in two versions.
-
product
System Components
For demanding computational tasks, Rohde & Schwarz offers the versatile, flexible equipment you need for everyday use – from the system controller and switch unit to the test chamber. All feature excellent EMC shielding, reliable test results and modular solutions.
-
product
RF Near Field Probe Set DC to 9GHz
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
product
Easy-to-assemble and Collapsible RF Test Enclosure With Fabric Shielding, ≥ 90 DB Isolation, 300 MHz - 18 GHz
dbTENT
The dbTENT is an easy-to-assemble, store and transport high-performance RF test enclosure. Whether you need to make measurements in the field or in the lab, the dbTENT provides superior 90 dB of isolation over a wide frequency range thanks to its patented double layer conductive fabric design. Featuring an interchangeable customisable I/O panel, the dbTENT meets all your needs for non-permanent isolated testing. With a setup time of only minutes, the dbTENT will get you ready for testing instantly in a wide variety of environments.
-
product
Digital Arrester Clamp Tester (with Data output)
ALCL-40H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER.*The least influence from the external magnetic field and noise by triple shielding of CT.*Compliant with IEC6099-5.*Enabled the measurements for 100nA resolution and harmonics current.
-
product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Radio Frequency Probes
In coaxially constructed radio frequency probes, the inner conductor is used for signal transmission, while the outer conductor serves as shielding. These probes are used for contacting many standardized RF connectors and RF sockets. Starting with larger Fakra or HSD connectors, over SMA, SMB, SMC connectors, up to small SMD-equipped switch connectors or for contacting directly on PCBs.
-
product
EMC Test & Measurement Solutions
MVG provides anechoic chambers and absorbing materials for antenna and EMC measurement and testing as well as RF and EMP shielding. Our SmartShieldTM modular shielding and precision cut and coated absorbers are designed with the flexibility to meet specific customer requirements. Our knowledge gained from over 30 years of experience ensures the high quality and durability of our products and the expertise from our team.
-
product
Plug'N Check
PH-320/300
The plug‵N′check is our easiest-to use cable tester yet. Simply plug in both ends of a cable, and the easy-to-read LED display explains the cable type and checks whether cable is faulty or good automatically. A shield LED shows results of the shielding check and battery low indicator saves you from misreading the tester in case of low power. Will make work shorter and easier for the layman and the professional alike. Especially suited for installation and maintenance of residential networks.
-
product
Custom Cable Assemblies
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
product
SNAPSHOT
PH-200
The Snapshot cable checker gives professionals and layman the ability to check cables instantly upon plug-in, with no buttons pressed or displays read. With its built-in memory, the Snapshot simply checks each cable plugged in against a correctly-configured cable pre-set by the user, and indicates the cable’s status with a sound. For pin-by-pin cable checking, the 〝standard check〞mode offers a plain LED-displayed check of the cable’s pins, checked automatically or manually. The Snapshot also generates a tone along the length of cables, making finding and following the cable with a tone probe a snap. A remote unit allows testing of already-installed cables, and a built-in line tester verifies phone line polarity and detects voltage before it threatens the safety of the test unit. A shield-test feature automatically tests cable shielding and a battery-low indicator prevents misreading results.
-
product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials. The fixture is a section of coaxial transmission line broken to allow the insertion of planar test materials. Although ASTM D4935-10 is currently limited to an upper frequency of 1.5 GHz, the EM-2108 meets and complies fully with both the impedance and SE requirements called out in ASTM test method D4935-10 up to 10 GHz. These results are shown in Figures 1 & 2. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred.
-
product
Starter Kit For B2985/B2987
N1410A
The N1410A is a starter kit for B2985B and B2987B Electrometer/High Resistance Meter and includes N1414A High resistance measurement universal adapter and N1415A Triax to alligator cable. The N1414A helps you setup the cables and makes the cabling setup easier. The N1415A is recommended to measure more than 1 nA current, but you can probably measure less than 1 nA current with appropriately shielding.
-
product
Blank Shielding Module, Receiver/ITA, 1 Module Position
510104129
Blank Modules are made from black anodized aluminum or black PEI thermoplastic and are for unused module slots. The Blank Shielding Module fills a module slot and shields signals between the modules. Blank Modules fit either ITA or Receiver positions.
-
product
True RMS RF Millivoltmeter
3440A
The 3440A measures the true rms of low level RF and microwave signals to over 1GHz. High rms accuracy, traceable to NIST, is assured regardless of waveshape. Common calibration errors are eliminated through temperature compensation of the probe detector diodes; double shielding protects the interchangeable probes from rough handling and pickup. Relative gain or loss measurements are simplified by a 0 dB reference adjustment. DC output proportional to the ac input is provided for analog recorders and to allow operation as an ac-dc converter.
-
product
Type 11C, CPCI, Rackmount/Wallmount
11C-CPCI
Elma Type 11C family of enclosures provides a high quality, cost effective pre-plated steel platform. Designed to IEEE 1101.10/.11 standards, Type 11C enclosures give advanced EMC shielding protection.
-
product
EMC
We will guide you through items that realize low-cost electromagnetic wave shielding measures (electromagnetic wave shielding: RF shielding), which is an issue at product development sites.
-
product
Absorber Lined Shielding Enclosure Measurements
ALSE
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
