-
Product
ESS Fixture
-
ESS - Environmental Stress Screening - is not a test. It is a product level screening process. ESS is part of manufacturing process, that verifies the operational parameters and guard bands of a product from an environmental - temperature, shock, vibration - point of view.
-
Product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
PCIe
M.2 Gen4 Socket3
-
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
Product
ICT/FCT-Fixtures (Large IF)
GenRad CK-2-228X
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
2m BNC Test Cable
16048D
Test Port Cable
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988EL
In-Circuit Test System
The i3070 Series 5i Inline ICT retains the popular and proprietary Keysight short-wire fixturing technology used in our stalwart Keysight 3070 and i3070 systems.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
SIMRC - RS232 to I2C Converter PCB
1080-001
-
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
Product
ESD Tester
PurePulse
-
PurePulse is a flexible and efficient ESD tester for HBM, TLP, MM and HMM. Its 2-pin style setup reduces tester parasitics, it captures waveform data and can be automated to test thousands of pins without the need for a test fixture. Our PurePulse system was designed from the ground up to be customized to meet your testing needs, take a look at the features below and schedule a demo with us to learn more.
-
Product
Insertion Aids
335016
-
To simplify handling when installing the assembly in the fixture, so-called insertion aids are installed as pre-centreers. - Stainless steel insertion aids - POM insertion aids (with M3x16 screw)
-
Product
SMD Array Type LCR Test Fixture
16034H
Test Fixture
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
Product
In-circuit Test
Medalist i1000 Systems
-
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
Product
Multi-Stage In-Circuit Test Fixtures
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 1.5 M
N1427A
Coaxial Cable
The N1427A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1427A to the B2985B/87B.
-
Product
Spectrum Analysis, Up To 26.5 GHz
S930902B
-
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Test Station TS 12x (Genrad 228x) And LH | 15+18
584004
-
Interface 15 slot or 18 slot. Put together the right fixture kit, consisting of housing and kit.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1 Small (Hold-Down Gate) / 230154
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
EBIRST 100-pin SCSI Termination Fixture
93-019-104
SCSI Female Terminator
93-019-104 eBIRST Termination Fixture is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
Product
PXI 12x8 RF Matrix 300MHz 50 SMB
40-726A-511
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
Ethernet Test Fixtures & Software
-
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Battery Research Tools
-
PotentioLab battery research tools support coin cell preparation, solid-state battery testing, electrode material evaluation and electrochemical laboratory workflows. Choose fixtures and accessories that improve consistency during sample preparation and cell testing.
-
Product
Mechanical, Ergonomic Adapter MMI-B
100639
-
Mechanical test fixture with optimised ergonomics for function test, final test and ICT applications. The MMI is prepared for both safety switches with guard locking and electrical interlocking. Our MMI-B test fixture is versatile.
-
Product
Functional Test Fixtures
Functional Test
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Solar Radiation Sensors
-
The solar radiation sensors that Campbell Scientific offers come in a variety of designs: pyranometers, net radiometers, quantum sensors, and pyrheliometers. These sensors measure various aspects of the energy imparted by the sun on the Earth’s surface. A leveling fixture fitted with a bubble level may be required to accurately install solar radiation sensors.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Non Contact Detectors
-
*Adjustable to safely detect power and low voltage*Safely detects AC voltage without touching the bare conductor*Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits*Use to detect voltage in outlets, lighting fixtures, wires and cables*Finds breaks in wires*Identifies hot and neutral conductors*Low battery indication
