Fixed Attenuators
Fix the degree of attenuation.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
NI-5191, 800 MHz, ±30 V, 10X Attenuation, Differential Active Oscilloscope Probe
781785-01
Oscilloscope
The NI-5191 is a differential, active voltage probe that offers 800 MHz of input bandwidth with a 10:1 attenuation ratio. You can use it with oscilloscopes that provide 50 Ω input impedance. You can power the probe using a Type-N barrel power connector from a USB port or using a 9 V alkaline battery.
-
-
Product
Programmable Step Attenuator DC~50GHz, 0~115dB Att.
-
The programmable step attenuator achieves step attenuation over a wide frequency band. It features high attenuation accuracy, excellent repeatability, low insertion loss, and long service life. Its primary applications include controlling the amplitude of signals entering systems, regulating output signal power in systems, and adjusting impedance matching between signal sources and loads. It is widely used in various broadband spectrum analyzers, broadband vector network analyzers, broadband synthesized signal sources, noise figure test sets, and diverse microwave automatic test systems.
-
Product
SP200B, 200 MHz, ±60 V, 1X or 10X Attenuation, Single-Ended Passive Oscilloscope Probe
780284-01
Oscilloscope Probe
The SP200B is a standard switchable passive probe for oscilloscopes that provide 1 MΩ input impedance. Depending on the attenuation ratio, the probe has an analog bandwidth of 6 MHz in the 1x attenuation setting or 200 MHz in the 10x attenuation setting.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
Fixed Network Thermal Cameras
FLIR FC-Series R (Automation)
-
The FC-Series R features on-board, non-contact temperature measurement capabilities for fire detection, safety, and thermal monitoring of substations, waste disposal, and valuable equipment. FC-Series R combines state-of-the-art image detail and on-board video analytics to provide reliable detection. Flexible alarming options include email, web and mobile apps, edge image storage, digital outputs, or VMS event notifications.
-
Product
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory
HVFO100-40X-TIP-U
-
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory.
-
Product
SMA Rotary Attenuator
WATT-6SR1101
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Setup Integrity Checker For B2980 Series, Fixed Perpetual License
N1420A
-
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
Product
Attenuator Assemblies
-
Any device designed to reduce the power of a wave or electrical signal without distorting it.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
Coaxial Programmable Attenuators
-
Coaxial attenuators are constructed with passivated stainless steel for durable use in both engineering labs and production line environments. These coaxial attenuators are designed and manufactured for low VSWR, low insertion loss and high attenuation value accuracy. The standard offering covers the frequency range of DC to 110 GHz and includes various interface options from 2.4 mm to 1 mm connector types as well as both male and female interfaces. The power handling of standard models is 0.5 to 1 watt continuous wave (CW). Higher power handling levels and different attenuation values and connector types from those listed below can also be requested.
-
Product
50 GHz Digital Setp Attenuator
PE43508
-
The PE43508 is a 50Ω, HaRP™ technology-enhanced, 6-bit RF digital step attenuator (DSA) that supports a wide frequency range from 9k to 50 GHz. It supports 1.8V control voltage and optional VSS_EXT bypass mode to improve spurious performance, making this device ideal for test and measurement, point-to-point communication systems, and very small aperture terminals (VSAT).
-
Product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
67% Beam Splitter BK7, Fixed Horizontal-Bend Mount
E1834J
Beam Splitter
The E1834J is a 67% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
Fixed Gas Detectors
-
Teledyne Gas & Flame Detection
Are you looking for reliable and efficient fixed gas detectors? Discover our detection devices especially designed for professionals in the industry and in the service sector.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
HVFO10X +/-1V (1x Attenuation) Universal Tip Accessory
HVFO100-1X-TIP-U
-
HVFO10X +/-1V (1x Attenuation) Universal Tip Accessory.
-
Product
Fixed Clamp-on Flowmeter
D118
-
Gentos Measurement & Control Co.
The D118 ultrasonic flowmeter is based on Tansit-time technology, which has ultra-high measurement accuracy. D118 uses an external clipped Transducer, which can collect flow data simply by clamping it on the outside of the pipe, and it will never come into contact with the fluid, and will not cause liquid pollution, pressure reduction, leakage, etc.
-
Product
Fixed Wing UAV
-
Fixed Wing UAV systems are fully automatic take-off and landing UAV designed to provide large area coverage and gather data at a higher resolution. These can be weaponised too as it can carry higher payloads.
-
Product
50% Beam Splitter BK7, Fixed Horizontal-Bend Mount
E1834G
Beam Splitter
The E1834G is a 50% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
Attenuators
-
We feature over 20,000 Microwave & RF Attenuators from 0-67GHz in stock. 1.85mm 67ghz attenuators. SMA attenuators to 3ghz, SMA Attenuators to 6ghz, 18ghz, & 27ghz; Type N attenuators to 6 ghz, 50 watt 3ghz Type N Attenuators, 500 watt 8.5ghz attenuators. Rotary, Variable, & Switch attenuators to 40Ghz. 2.4mm 50ghz attenuators.
-
Product
Attenuation 1000 High Voltage Passive Probe
-
* high voltage multimeter probe is a 1000:1 fixed attenuation ratio passive probe. This probe is designed to test high voltages for multimeters. With high voltage and high precision.* The test signal can be read on the multimeter, and the multimeter multiplied by 1000 is the actual test result.* High reliability and high security.* The highest voltage can measure DC up to 30KV.
-
Product
Fixed Power Analyzers
-
Network analyzers are devices that are essential for measuring electrical parameters and controlling industrial processes. They provide the user relevant, real-time information for managing energy consumption and checking the quality of supply and consumption in their installation. They offer multiple communication options, inputs and outputs to manage any alarm that may appear in the installation, and provide analyses and reports on the performance of their network.
-
Product
Fixed Writing Surface for Double-Bay 19" RA & RC Cabinets
WS2-119
-
This fixed shelf / writing surface for a double-bay RA & RC cabinets spans the full width of the cabinet and extends 18” in front.
-
Product
Programmable Attenuators
-
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
Attenuator
RFATT AXIe-0
-
*Dual channel AXIe attenuator with frequency range from 9 kHz to 10 GHz.*The module is designed to work as part of information measuring systems as a normalizer of radio frequency signals (power control: signal amplification or attenuation).
-
Product
Telephone Attenuators & RFI Filters
-
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
