Filter Results By:
Products
Applications
Manufacturers
-
product
Wireless Communications
Schweitzer Engineering Laboratories, Inc.
Wireless communications extend networks in areas where communications wires are not available or cost-prohibitive.
-
product
DAS
The Distributed Antenna Systems (DAS) function is to enhance the performance of a wireless network coverage of a specific area. DAS is a network of antennas which are all connected to the same source. The DAS solution is more efficient than having a large single antenna to cover an area and that’s why it is highly suited for in-buildings service and a restricted outdoor area. Amphenol Procom offers a wide range of both indoor antennas and passive devices, especially for Public Safety applications.
-
product
Wireless
Virtual Panels
Designed with flexible work solutions in mind, the Virtual Panel enables remote users to access the full audio capabilities of the intercom system from anywhere, at any time, and be up and running in minutes without the need for dedicated operator hardware. Individual users will access the intercom via a familiar, modern software panel screen on the chosen device and a SIP connection over standard network (either wired, wireless of a combination of both). Having the audio managed by a SIP connection means the panel users are truly flexible as there is no physical connection to any dedicated hardware - it?s all in the cloud.
-
product
LiFi-GigaDock Evaluation-Kit
Offered for testing, evaluation and demonstration purposes, the Li-Fi GigaDock ® evaluation kits enable the establishment of a full-duplex, short-distance, cm-level optical wireless bi-directional point-to-point data link. The GD-5G offers bi-directional communication with a data rate of up to 5 Gbit/s and SMA connectivity. The GD-1G can be connected to an Ethernet network via an RJ45 connector with a Cat 5 cable or directly to a PC and offers a data rate of up to 1 Gbit/s.
-
product
Carrier Convergence Processors
Macom Technology Solutions Holdings Inc.
Macom offers a line of infrastructure voice processors, in concert with the carrier-grade Media Stream Processing software, that delivers a complete, integrated VoIP media, data and fax, signaling and control processing solution. Combined with powerful DSP cores with flexible packet processing engine and a rich set of interfaces, the processors support 256 to 640 channels of packet-TDM and packet-packet operation across the entire range of IP modulations, for VoIP and VoATM applications. A large suite of software packages for Wireline, Packet Cable, W-CDMA and CDMA2000 network applications are supported. Major applications include media gateways, session boarder controllers, wireless base transceiver stations and nod-Bs, base station controllers, radio network controllers, mobile switching centers, digital loop carriers, optical network terminals and optical line terminals for passive optical networks, digital subscriber line access multiplexers, class 4 and 5 switches, integrated access devices, IP private branch exchanges, ATM switches and IP routers.
-
product
USRP-2940, 50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783146-01
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
10Gbps Tunable ROSA For NGPON2
With increasing demand for data and video from home, business and wireless, higher and higher bandwidth for the Optical Access Network is required.
-
product
Interactive Display Networking
Wireless interactive display that connects to the network and the display in a presentation or classroom environment
-
product
PXI-5671, 2.7 GHz RF Vector Signal Generators
779079-04
2.7 GHz, Digital Upconverter Included, PXI Vector Signal Generator—The PXI‑5671 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5671 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software-defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee
-
product
Cellular Antennas
Our portfolio of cellular antennas includes solutions for emerging technologies such as 5G, as well as coverage of older networks such as 2G, 3G, 4G, and CBRS. A wide range of internal/embedded antennas and externally mounted antennas are available to suit a wide range of customer requirements. Our cellular antennas are available for regions, frequencies, and standards, with products ranging from 617 - 7125 MHz. Choose from a variety of antenna types, product length, width, and height, and wireless application. Custom antenna developments are regularly undertaken to meet specific customer requirements. Our cellular antenna portfolio includes products manufactured by TE Connectivity, Laird Connectivity External Antennas, and Hirschmann Car Communications.
-
product
Data Loggers
Record network data over time and/or based on location; standalone, wireless and remote capabilities available.
-
product
Air Interface Emulator
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
RF Ports Alignment Software
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
product
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783923-01
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
Satellite and Aerospace Channel Emulation Toolset
S8825A
Satellite, aerospace, and airborne radio link testing with realistic wireless propagation conditions. 5G NTN test support with satellite connection from mobile phones. Interconnecting networks for full end-to-end system testing.
-
product
PXIe-5672, 2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator
779900-01
2.7 GHz, 20 MHz Bandwidth Digital Upconverter Included, PXI Vector Signal Generator —The PXIe‑5672 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5672 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee.
-
product
Wireless Network Penetration Testing
LGMS wireless network penetration testing uses automated and manual penetration techniques to locate and map authorized and unauthorized wireless access points, review corporate access point configuration and then discover weaknesses that could allow an attacker to penetrate those networks. Potential internal and external threats are documented, and a recommended action plan is developed to address any security risks.
-
product
Test Engineering
With a thorough knowledge of various internet connectivity products, Xebrium’s team of Software Engineers, Network Engineers, and Test Engineers are relied upon to implement and rigorously test networking and wireless product.
-
product
Serial Device Server
SD-330AC-1402
The Silex SD-330AC-1402 features a FIPS 140-2 wireless/wired LAN Serial Device Server and an Ethernet to Wi-Fi Bridge. Devices equipped with the RS-232C serial interfaces can join a Ethernet LAN or wireless LAN. Devices with an Ethernet port are also transformed to a wireless network devices. Medical devices, printers, scanners or virtually any other device with a serial port or an Ethernet port can now be enabled with secure and robust LAN network capability. The SD-330AC-1402 can be simply added to US government facilities to enhance device networking connectivity.
-
product
Call Generator (Voice / Data)
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is an automatic call generator, that establishes voice and data calls to and from actual mobile devices in the test system. Voice calls can be generated via the wireless PLMN network using actual mobile devices, via the PSTN network through analogue or ISDN lines or via Voice over IP. Wireless data sessions can be setup through the 3G or 4G network or over WiFi.
-
product
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device
783924-01
400 MHz to 4.4 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2942 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
WiFiScope WS5: 200 MS/s 250MHz BW, 2 Channel, Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
WS5-220XM-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
product
RF Spectrum Analyzers
RF Explorer
RF Explorer is a new series of low-cost, portable, RF spectrum analyzers designed by Arocholl that are available in a variety of frequency ranges. Nuts About Nets has been developing diagnostic tools for troubleshooting wireless networks for a number of years and when RF Explorer was first introduced to us we were extremely impressed. The price-performance of these RF spectrum analyzers is truly remarkable and is the best, by far, on the market -- nothing else comes close. These RF analyzers operate both standalone as handheld devices, plus they interface via USB cable to a PC running more sophisticated data acquisition and analysis software. Prices for these RF spectrum analyzers (including PC software) begin at $119 USD -- which is unheard of in the test equipment industry.
-
product
IMS-SIP Network Emulator Software
E6966B
Wireless telephony networks are increasing capacity for high throughput Internet Protocol (IP) packed-data by utilizing radio access technologies such as LTE and HSPA. Session Initiation Protocol (SIP) and IP Multimedia Subsystem (IMS) are progressively being adopted as part of the network infrastructure to carry traditional wireless telephony services over an all-IP network. SIP provides control of communication sessions whilst IMS is the framework that allows delivery of multimedia services over IP. With this new capability comes the need for developers and operators to move their focus to testing user equipment (UE) in this new network environment.
-
product
50 MHz to 2.2 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783926-01
50 MHz to 2.2 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2950 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. With the flexible hardware architecture and the LabVIEW unified design flow, researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2950 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
Networks
Our products include wireless network solutions, mobile ad hoc networks, provisioned applications and virtualized environments networking; interference-resistant technologies and satellites. Our RF-based systems give customers a pivotal advantage in today's complex network environments. We transfer concepts into reality, enabling fast, reliable delivery of information and intelligence to individual terminals while ensuring interoperability across vast, dynamic networks.
-
product
Wi-Fi signal analysers
An advanced Wi-Fi analyser is essential to avoid channel interferences in large public or corporate wireless networks.
-
product
End-To-End Performance Testing
IxLoad Wireless
Keysight Network Applications and Security
IxLoad Wireless enables mobile operators and equipment manufacturers to test and validate complex wireless networks and components for greater end-to-end service quality. This “lab to live” LTE testing solution recreates networking environments and real-world subscriber traffic, such as voice, video, and data. At the same time, it emulates multiple mobile subscriber activities—including handovers, TAU, and idle-connected transitions—for comprehensive test coverage. Whether modeling the behavior of thousands of subscribers or measuring end-user experience, IxLoad enables mobile operators to fast-track new networks and services with confidence.
-
product
USRP-2944, 10 MHz to 6 GHz, Reconfigurable USRP Software Defined Radio Device
783149-01
The USRP-2944 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
