-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Environmental Chamber
REXMED REC-400
-
MOD. REC-400, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,506 Watts, 11,962 BTU/hr, 3,020 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Environmental Test Chambers
ET-Series
-
Environmental Test Chambers are designed with uncompromised features included in the system to meet your changing application needs of simulation of wide range of temperature, relative humidity etc., conditions without the added cost of expensive add-on’s as options. Available in varied volumes to fit your differing specimen sizes
-
Product
Composite Salt Spray Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Multi-Environment Simulation: Replicates accelerated corrosion in marine, industrial, or road salt conditions with cyclic temperature/humidity stress.- Advanced Control: 7-inch HMI touchscreen with 100+ pre-set programs, real-time graphs, and remote monitoring via Wi-Fi/Ethernet.- Durability: FRP (fiber-reinforced plastic) housing, titanium alloy heaters, and quartz heating tubes for resistance to acidic/alkali corrosion.- Eco-Friendly Design: Closed-loop filtration system (recycles 70% of spray solution) and R290/R513A refrigerants (low GWP).- Safety & Maintenance: Leak detection, over-temperature cutoffs, and self-cleaning nozzles to minimize downtime.
-
Product
Temperature Cycling Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Temperature cycling test chamber is suitable for testing various performance indexes of aerospace products, electronic instruments, materials, electronic products and various electronic components under the condition of rapid temperature change.
-
-
Product
IEC60529 IPX9K Waterproof Test Chamber
CX-IPX9
-
Shenzhen Chuangxin Instruments Co., Ltd.
The main purpose of the equipment is to test product performance of storage, transportation and use in the rain condition.The equipment, mainly used in electronic and electrical products, lamps ,lanterns, electrical cabinets, electrical components, automobiles, motorcycles and their parts etc, tests physical and other related properties of products by simulating the rain condition.After test, judge if the performance of the product meets the demand by verification for product design, improvement, check and factory inspection use.
-
Product
Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Thermal Shock Chamber: -70℃~150℃, ≤5min recovery, meets MIL-STD-810. Ideal for PCB/IC reliability testing.- ESS Environmental Chamber: Humidity 20%~98% RH, supports GB/T 2423 standards. 40% energy saving vs. competitors.- Liquid-to-Liquid Shock Tester: LN₂ cooling to -196℃, 15s transition time. For aerospace materials validation.- Thermal Cycling Equipment: 25℃/min ramp rate, 1000L capacity. JESD22-A104 compliant.- Benchtop Thermal Chamber: -65℃~150℃, 65dB low noise. Lab-use with USB data export.
-
Product
Chamber Light
LED-CL
-
The Teledyne Bowtech LED-CL Chamber Light is extremely safe and reliable, due to its advanced technology and innovation.The light has 100,000 hour life and has been designed specifically for use within the Hyperbaric Diving environment, whether that is in Hyperbaric Chambers, TUP's, Diving Bells or even Wet Bells.
-
Product
Non-Nitrogen HALT Chamber
-
An advanced environmental test system that performs Highly Accelerated Life Testing (HALT) without relying on costly liquid nitrogen (LN2) for rapid cooling.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Box Rain Test Chamber
-
Comprehensive box rain test chamber (with swing pipe and right angle tube) is used to test the electric and electronic devices by simulating natural rainfall with spraying water from the water nozzles (holes) on swing pipe or straight tube. To estimate and recognize if the shell or sealing elements of these device could ensure a good condition of working during and after the test. The products are widely used in the industries of light, electrical, electronics, automobile, motorcycle, household electric appliances, electromechanical equipment, instruments and meters, and other industries.
-
Product
Anechoic Chambers
-
Eckel Noise Control Technologies
Anechoic Chambers are echo-free enclosures with a sound energy absorption level of 99% to 100%, or a reflected sound pressure level of 10% or less. The frequency at which the energy absorption drops below 99%, or the pressure reflection exceeds 10%, is known as the low-frequency cut-off. Sound absorption is obtained by lining the walls, ceilings, and floor with wedges or other sound absorbing elements or SuperSoft panels, depending on performance level required and cut-off desired.
-
Product
High Temperature Aging Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's High Temperature Aging Chamber is widely applied for automotive parts ,electronic and electric products ,components and materials by constant high temperature reliability test.
-
Product
Thermal Shock Chambers
-
The chamber is divided into 3 parts:Hight temperature zone, low temperature zone, and the testing zone. Special heat isolating structure and preserve cold and heat treatment.
-
Product
Temperature and Humidity Test Chambers
-
Labodam temperature and humidity test chambers are designed to simulate constant climactic conditions for testing a wide variety of products for their quality, performance, shelf life, and stability.
-
Product
UV Test Chambers
-
Labodam provides an excellent range of UV test chambers operating at a variety of UV wavelengths to simulate different light conditions.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Tensile Testing System With Thermostatic Chamber
-
This thermostatic chamber is ideal for long-stroke tensile testing of large-elongation materials such as rubber and plastic in controlled temperature environments.
-
Product
IP X7, X8 - Waterproof Test Chamber
-
The IP X7 and IP X8 test equipment simulates the water immersion environment to test the water resistance and sealing of the samples during storage, transportation and usage. It is widely applied to electrical and electronic products, lamps and lanterns, electrical cabinet, electrical components, automobile, motorcycle and its spare parts and other products. It provides the basis to improve the performance of the products.
-
Product
Reach-In Humidity Test Chamber
-
The Humidity Test Chambers from Weiber are corrosion test chambers that are used to simulate high or low humidity conditions for testing the rust preventing capacity of various oils and greases. These high low humidity simulation chambers find wide spread usage in research organizations, educational institutions and industrial units and are most commonly employed by petroleum and chemical industries.
-
Product
Test Chamber
Immunity
-
Laplace can supply high performance mobile, bespoke and customised mobile RF and Antenna chambers which have been developed to meet all types of customers’ requirements. These mobile RF and Antenna chambers are very high performance and offer +100db of shielding attenuation @ 40GHz and can be fitted with best-in-class absorbers rated up to 110 GHz.
-
Product
Altitude and Vacuum Chambers
A series
-
Bemco's acclaimed Altitude and Vacuum Chambers are designed to meet the need for a combination, easy to use altitude testing chamber, and ruggedly built vacuum processing facility. Today's modern A series chambers feature another Bemco first, a standard Brooks Automation, Granville-Phillips Series 375 Convectron Gauge Controller.
-
Product
Solid Walk-In Chambers
-
EWS chambers are solid, one-piece construction, using fiberglass insulation and an angle-iron frame. The stainless steel interior liner is reinforced and continuously welded, including leak-testing for integrity.
-
Product
Waterproof Test Chamber
JL-XC
-
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
Product
MIL-STD 461 & DO-160 Chambers
-
Cuming-Lehman Chambers MIL-STD 461E/F test chamber is specially designed for testing in accordance with the military standard.
-
Product
Constant Temperature Chamber
-
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
Product
Thermostatic Chambers
-
Various test devices are available for tensile, bending and compression testing in specific environments.
-
Product
Composite Salt Spray Test Chamber
YWX/Q-010X
-
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
Product
UV Weather Resistance Test Chamber
-
This series is applicable for the sunlight resistant test of nonmetallic materials and aging test of artificial light source.
