-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
-
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
LAN Router
BB-SR30019125-SWH
Router
SmartFlex, Global, 5x Ethernet, Wi-Fi, PoE PD, Metal, International Power Supply (EU, US, UK, AUS). VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
CompactPCI 2 Slot 1U
-
1U, 19″ Rackmount system with hot removable CPCI 3U Power Supply, four Powerful Fans and CompactPCI Backplane. The system support 6U cards Front and Rear. Additional four fans are available for optimal Front and RTM cooling solution. The Backplane is compliant with PICMG 2.0 R3.0 with 64bit 66MHz & supports boards with hot swap capability PICMG 2.1 R2.0. All five CompactPCI connectors (J1-J5) are available on the backplane. The system slot is located on the lower-slot.
-
Product
Digital Portable Panel Meters
ST-2001 ACV
-
Standard Electric Works Co., Ltd
● Big-size LCD (112 x 59mm)● Backlight function.● Analog scale with Bar-graph for viewing. (100 bars)● 10000 counts (high resolution).● DCV Ranges: 99.99mV~999.9V (ST-2001 DCV). ● ACV Ranges: 99.99mV~800.0V (ST-2001 ACV). ● 5 manual ranges controlled by rotary switch.● Data Hold function● Low battery indication● 9V power supply● Best resolution of 0.01mV (10uV)● Precision meter for factory maintenance, field servicing and educational purposes.● With an optical USB to RS-232 data transmission cable. (DCV-R & ACV-R)● 2 optical LEDs are built-in for data transfer. (DCV-R & ACV-R)● Well isolated to contact. (DCV-R & ACV-R)● The software is included (Compact disc). (DCV-R & ACV-R)
-
Product
Programmable DC Power Supply
IT6100 Series
-
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
Product
Battery on-line Monitoring Tester
-
HD Power Test Equipment Co.ltd
Battery on-line monitoring system tester is a on-line battery monitoring and auto maintain system for USP,EPS, DC power supply, communication power supply . The tester has the function of monitoring and alerting for a series of parameters such as battery pack voltage, battery pack current, cell battery voltage, cell battery internal resistance, battery environment temperature, Cell Battery negative temperature and battery voltage balance, residual capacity and discharge. It can automatically maintain balance voltage, which used for on-line monitoring 2V and 12V battery.
-
Product
50W Power Supply, 8V, 5A or 20V, 2.5A
E3642A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 50W, single output E3642A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
Product
Power Supply
-
Rishabh Instruments Pvt. Ltd.,
1Phase, 115-230Vac I/P& 24Vdc 384 to 480 W O/p, Adjustable o/p voltage range 22 – 27 Vdc. High efficiency ≥92% & compact size (w-h-d) 85x120x140 mm & DIN Rail Mountable
-
Product
Solar Array Simulator
Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
Custom Configured MPS, 600W
N6711C
Power Supply
The Keysight N6711C is a 600 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6711C consists of 1 N6701C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6711C.
-
Product
2 PICMG® CPU, 10 PCI™, 4 ISA Slots Backplane
HPCI-15S10
Backplane
- Segment: 1- Slots: 2 PICMG® CPU, 10 PCI™, 4 ISA- Supports AT, ATX power supplies- Dimensions: 317 mm x 264.2 mm
-
Product
XCITE 1300 Laboratory Series
-
The Xcite 1300 Laboratory Series is used in applications where longer stroke and extremely high forces are required to determine the modal characteristics of flexible structures such as truck suspensions and engine mounts, transit vehicles, locomotives, drag lines, backhoes, cranes and large electrical generating apparatus. The 15 GPM Hydraulic Power Supply of these systems allows frequency responses in the 100 Hz to 500 Hz range while the larger exciters generate forces to 20,000 lbf.
-
Product
3000W-3200W 3-Phase Input Industrial AC-DC Power Supplies
TPS3000
-
The TPS3000 industrial AC-DC power supplies offer output power up to 3.2kW in a 2U high package with 3 phase supply input.Features include voltage and current programming, remote on/off, remote sense, a standby supply, PMBus communication, built in ORing FET and wide operating temparature range of -40°C to +70°C
-
Product
AC-DC Power Supply Solutions
-
Advanced Conversion Technology, Inc
From single to three phase inputs, 60 Hz or 400 Hz, ACT can provide you with a design to meet your demanding applications. ACT can also provide designs that incorporate an active PFC front end, single and three phase, which provides less than 3% total current harmonic distortion.
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
HDCD Battery Charge Tester
-
HD Power Test Equipment Co.ltd
HDCD Battery Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It keeps the constant communication maintain between the battery charge ensuring a perfect charge.Battery charge tester is designed using intelligent three-stage charging mode to achieve the function of automatic conservation between charging and floating charge. It also can on-line detect the voltage of the whole battery, real-time display and record the voltage of whole battery. The tester can automatically accomplish charging after setting the parameter of voltage, current, time and capacity.
-
Product
VB-8054, 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-12
-
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
Product
Chassis Mount / Open Frame AC-DC Power Supplies
-
Chassis Mount / Open Frame AC-DC Power Supplies
-
Product
D-Type Surge Generator
-
Shanghai Guantu Technology Co., Ltd.
Meet and exceed the new standards of IEC61000-4-5 and GB/T17626.5;Chinese and English switching, programmable operation, easy to use;7.0 color touch screen display, more convenient operation;Imported program-controlled high-voltage power supply with stable performance;Built-in ambient temperature and humidity display;The surge test mode is automatically switched in all gears, without manual operation;Built-in level parameters, positive and negative automatic switching, easy to operate;Built-in RS232 interface, convenient for product upgrades, optional measurement and control software for remote control.
-
Product
Power Supplies
V-500
-
The V-500 is perfect for casual, everyday users who need an efficient power supply that can deliver the watts necessary without all the additional features. With components designed for longer life, the V-500 is the perfect candidate. It has a silent 120mm fan that is quiet to the ears with maximum cooling efficiency. Also with neat cable wires, the V-500 is simple to use, easy to install, and still has all the power necessary to run your system smoothly.
-
Product
Power Supply, 6V, 180A, 1080W
N5761A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight 1080W, single output N5761A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers solid performance and a variety of basic and enhanced capabilities in a compact 1U package.
-
Product
SWB-2816, 8x46, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-16
Reed Relay
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, … individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI 32 Channel I/O, Low Side Driver
40-413-002
Digital I/O
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
Product
12V Automobile Power Supply
7500A
-
Peaceful Thriving Enterprise Co Ltd
This is 12V automobile power supply. Avoid the loss of memory during the vehicle's battery replacement.
-
Product
Power Supply, 60V, 55A, 3300W
N8737A
Power Supply
Keysight N8737A is a high-performance 60V power supply with a small footprint and flexible AC input options. A reliable solution for your high-power applications.
-
Product
DC Power Supply, 30V, 5A
U8002A
DC Power Supply
The Keysight U8002A 30V/5A single-output, non-programmable DC power supplies is suitable for a variety of electronics manufacturing applications. With our affordable pricing, it is also well suited for usage in education labs.
-
Product
2U Storage Chassis For ATX/EATX Serverboard With 12 Hot-Swap Drive Bays For High-Capacity Storage.
HPC-8212
-
2U rackmount chassis supports EATX/ATX/uATX motherboard12-bay hot-swappable 3.5"/2.5" SAS 12Gb/s drives or SATA 6Gb/s drives4 x NVMe drives supported via an optional riser cardDefault 7x slots (low profile) rear panel, 3x slots (full height) optionalSupports Flex ATX Power, 80+ redundant power supply
-
Product
PCB Track Resistance Calculator
TRC100
-
The TRC100 is a handy free utility which lets you enter track shape and length, along with material type, the TRC100 will give you an answer in Ohms for the trace you describe. TRC100 is useful if you are working on fine geometries, and need to take care about series loss. You may also find TRC100 useful in power supply applications.
