Filter Results By:
Products
Applications
Manufacturers
Protocol Analyzers
Analyze the hardware and/or software of the connection, communication, and data transfer between devices.
See Also: Protocol Test, Packet Analyzers
-
product
PMC Bus Analyzer / Exerciser
PMC650
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
product
Bus Analyzer / Exerciser
VME850P2
The VME850P2 analyzer is an optional plug on module for the VME850 analyzer that adds analyzer and exerciser functions to the VME850 analyzer for the P2 connector. This module allows the user to monitor and stimulate the A, C and D rows of the 160 pin P2 connector. Although the VME850P2 analyzer is in a PMC form factor it is not compatible with the PMC protocols and signaling. The signaling levels on the P2 connector must be less then 5V in order to prevent damage of the analyzer.
-
product
Ethernet Tester
ProPlex IQ
Ethernet tester for entertainment production applications. Designed with input from production and staging professionals as an all-in-one device, it provides feedback and analysis on any Ethernet protocol, as well as network troubleshooting. It can act as a DMX cable tester, DMX receiver/transmitter, DMX timing analyzer, DMX recorder, RDM controller, or a bidirectional Ethernet-DMX gateway. It is also a PoE tester that can determine the capabilities of any connected PoE source. Finally, it can check SMPTE timecode or act as an LTC receiver/analyzer, and LTC transmitter, and users can use it to update Solaris/ProPlex firmware without a PC.
-
product
Envision Analyzer & Generator
MIPI C-PHY/D-PHY
The Envision X14 Analyzer capture utility provides deep analysis for MIPI camera and display protocols over C-PHY and D-PHY layers. The X14 Analyzer can be positioned either as an endpoint to test a CSI-2 or DSI-2 stream or tapped in between a CSI-2 or DSI-2 device and host for passive monitoring and analysis. The Envision X14 ensures fast Time-to-Insight through its rich set of innovative features for debug analysis and identifying and resolving elusive protocol errors.
-
product
I2C Protocol Analyzer
EasyI2C
It's simple to find an I2C-style bus within arm's reach. Every computer, monitor, television and cell phone has it. Most microcontrollers directly support this protocol as well. Even so, the I2C protocol has many subtle nuances that are hard to grasp and easily forgotten. EasyI2C (TM) helps you to figure out exactly what is happening, without having to examine huge waveform trace capture files or set up complex tests.
-
product
Detective Logic Analyzer
LPDDR5
Provides logic analyzer like deep transaction Listing and Waveform capture. Can store up to 512M of captured States at up to 6400+ MT/sContinuous, real time analysis, not post-processing 2D (voltage & time) Eye Detector guarantees valid data acquisition on each signalExtensive Triggering and Storage Qualification allows precise insightIndustry Leading Protocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specifications, NOT post processing. No other tool can provide this!Mode Register Listing provided
-
product
SAS 4.0 Protocol Analyzer
Sierra T244
The Sierra T244 is a SAS 4.0 protocol analyzer designed to non-intrusively capture up to four 24 Gb/s SAS logical links providing unmatched analysis and debug capabilities for developers working on next generation storage systems, devices and software.
-
product
Mobilize
A complete wireless solution that connects your Pronk test equipment to your smart device!* Take complete control of your Pronk products — Safe-T Sim® Mobilize Electrical Safety Analyzer, Mobilize SC-5 SimCube® NIBP Simulator, Mobilize OX-2 OxSim Flex® SpO2 Simulator, and Mobilize FlowTrax® IV Pump Analyzer — to set up your own test protocols or run your CMMS procedures right from your Apple iOS device.
-
product
PCIe 5.0 Protocol Analyzer
P5552A
The Keysight P5552A PCIe 5.0 Protocol Analyzer introduces a new form factor that is easily deployable in the lab bench environment to enable deep protocol analysis of a PCIe system with unparallel signal integrity. Locate protocol errors or validate device operations by viewing data from the physical layer all through the transactional layer with ease.
-
product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Protocol Analyzer
Zeroplus Technology Corperation
Is a measurement tool or device used to capture and monitor the data over communication channel.
-
product
Bus Analyzer / Exerciser
PCF650
The PCF650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
product
Communication Protocol Analyzer
LE-200PR
LE-200PR is a lightweight communication protocol analyzer has a Data Logger function to record data in the SD card for long hours. It is a high performance model, which has same function as LE-200PS and also supports remote control by Wi-Fi.
-
product
Compact Protocol Analyzer
LE-1500R
"LE-1500R" is a protocol analyzer (line monitor) dedicated for asynchronous communication monitoring with affordable pricing. LE-1500R can run as a stand- alone by the internal battery for long time and can be remotely controled by a PC or a smart phone via Wi-Fi (Wi-Fi function is available only in USA, Canada, Japan, and EU). The analyzer has a TTL measurement port (which supports UART communication) as its standard port besides RS-232C, RS-422, and RS-485. It can monitor communication data of max 500Kbps for up to 32MB (8,000,000 data) in real time and also can execute a simulation testing of send/receive data. It also has a BERT function (which is not equipped with the analyzers of this pricing level) as its standard function. The correct time stamp, the measurement of idel time (which are the difficult for other software analyzers), and the capturing ability (without missing data) are the best options for trouble shooting and development test of a communication sytem which requires a reliablity.
-
product
I3C Protocol Analyzer and Exerciser
PGY-I3C-EX-PD
Prodigy Technovations Pvt. Ltd.
I3C Protocol Analyzer (PGY-I3C-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. I3C Serial bus interface is emerging as a chosen interface for all future sensor connectivity in mobile phone and automotive Industry. This could also be chosen for low cost, reliable interface for future embedded electronic applications to address the new data intensive applications.
-
product
Protocol Analyzers
International Test Instruments Corp.
The Bus Analyzer, is capable of capturing and decoding real-time LS, FS and HS USB Transactions as well as OTG SRP, OTG HNP and OTG VBus events. It has unlimited capture length (only limited by the RAM in the analysis PC as the captured data is viewed), immediate display of very large recorded capture data (data is streamed in real-time into the tree view as it is captured from the link under test or from file so you will not have to wait before you can start analyzing the data) as well as a very small physical format which makes it a powerful companion in your laptop bag or in the lab.
-
product
3-in-1 Analyzer: Logic Analyzer, Protocol Analyzer, Simple DSO
MSO2216B+
3-in-1 Analyzer : Logic Analyzer, Protocol Analyzer, Simple DSO• PC-based, USB3.0 interface• 8 / 16 Channels(display digital and analog waveforms of the same channel)• Digital Inputs : 2 GHz Timing, 200MHz State Analysis (Max.)• Analog Inputs : 200 MS/s (Max.), Bandwidth 40 MHz• 8 Gb Memory (Max.)• PC RAM storage for streaming mode• Utility model patent of Taiwan number M601827
-
product
Bus Analyzer
FireSpy® 4432bT/4832bT
The FireSpy4432bT and FireSpy4832bT bus analyzers are DapTechnology's latest 4-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy4432bT/4832bT are the most advanced 1394 test equipment in the market. The FireSpy4432bT/4832bT in fact combine four FireSpy analyzers in one single instrument. They comprise a significantly more powerful on-board processor and improved connectivity to the host.
-
product
Communication Data Logger
LE-270A
LE-270A is a Communication Data Logger, which records CAN/LIN communication logs in the SD/SDHC card for long hours. Using with a PC, it performs as a CAN/LIN protocol analyzer, and monitors data on the PC at real time (Line Monitor). Using without a PC, it performs as the CAN/LIN data logger, and saves data in the SD/SDHC card. It has two High-speed CAN transceivers, two Low-speed CAN transceivers and two LIN (TJA1020) transceivers. It monitors two channels of CAN or LIN, or one CAN and one LIN transceivers. In addition, four channels of Analog/Digital signals can be recorded.
-
product
Bus Analyzer
FireSpy® 3432bT/3832bT
The FireSpy3832bT and FireSpy3432bT bus analyzers are DapTechnology's latest 3-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy3432bT/3832bT is the most advanced 1394 test equipments in the market. The FireSpy3x32bT in fact combines three FireSpy analyzers in one single instrument. It comprises a significantly more powerful on-board processor and improved connectivity to the host.
-
product
LAN⇔RS-232C Conversion
SI-60F
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
product
JTAG Protocol Exerciser and Analyzer
PGY-JTAG-EX-PD
Prodigy Technovations Pvt. Ltd.
JTAG Protocol Analyzer (PGY-JTAG-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-JTAG-EX-PD is the leading instrument that enables the design and test engineers to test the respective JTAG designs for its specifications by configuring the PGY-JTAG-EX-PD as Master/Slave, generating JTAG traffic and decoding the JTAG protocol decode packets.
-
product
Multi-Layer Analyzers
LTE-Advanced Xpert™
The LTE-Advanced Xpert multi-layer analyzer is a unique, real-time continuous protocol analyzer for LTE and LTE-Advanced networks. Installed between a base station and its served mobile devices, the LTE-Advanced Xpert captures the LTE-Uu uplink and downlink transmission and performs deciphering and analysis of data and control channels in real time.
-
product
FLUTE Analyzer
FLUTE is a protocol for the unidirectional delivery of files over the Internet. The FLUTE Analyzer provides an in-depth analysis and continuous monitoring of FLUTE data carousels.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Fibre Channel, Ethernet, & MIL-Firewire Protocol Analyzer
Cipher
Avionics Interface Technologies
Supports Multiple Network Protocols including Ethernet, FibreChannel, & MIL-Firewire (AS5643) - High Performance Filtering & Search - Built-in protocol decoders for: FC-AE-ASM, FC-AE-RDMA, FCAE-1553, AS5643, Ethernet, IPv4, IPv6, UDP - User defined “protocol decoders” for custom & proprietary protocols - Database architecture for handling very large data sets - Multiple, Simultaneous views of data sets with time correlation of data across multiple views. - Compatible with common network analysis tools such as - Wireshark (e.g. Imports/Exports to PCAPNG) - Compatible with AIT’s Fibre Channel Test - Instruments for live capture, triggering, and filtering.
-
product
MIPI Soundwire Total IP Solutions
Soundwire
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
product
network analyzer
Capsa Free
Capsa Free is a must-have freeware network analyzer and packet sniffer for Ethernet monitoring, troubleshooting and analysis. Capsa Free is a perfect choice for students, teachers and computer geeks to learn protocols and networking technology knowledge. The Capsa Free freeware application by Colasoft is one of the most popular free packet sniffer products available.
-
product
IEC61850 Digital Substation Testing
With the development of power system, more and more digital substation based on IEC61850 has been built in the world. IEC61850 is the new communication protocol which is adopted by power system so as to change the analog complicated wiring connection and protocol conversion. Based on IEC61850, all Messages, such as GOOSE, SV, MMS, PTP, etc, could be communicated on the Ethernet via fiber optical cable connection. In China, the digital substation have started since 2003, until now there are already more than 6000 digital substation put on operation, China Power Grid is planning to build 5000 more new digital substations. PONOVO, as the leading power system testing solution provider, have launched plenty of IEC61850 digital testing tools, not only digital relay test set, but also MU test set, multi-functional analyzer, 24 hours online monitoring and analyzing system, etc so that users could have suitable testing equipment for the digital substation commissioning and testings.
