Earth Leakage Circuit Breaker Testers
test trip time and trip current values.
-
Product
Closed Cup Flash Point Testers
-
Labodam closed-cup flash point testers are compact, stand-alone solutions which determine the low temperature operability in diesel fuel, biodiesel, blends and gas oils. They are designed as per Test Methods for Flash Point of Petroleum Products (Pensky-Martens Closed Cup Methods).
-
Product
6 Sided Bed of Nails Testers
BoxProber Family
-
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Deadweight Testers & Gauges
-
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area.
-
Product
TACAN/DME Station Tester
EDST300
-
The R&S®EDST300 TACAN/DME station tester is an analyzer designed for commissioning, testing and servicing pulsed terrestrial navigation systems.
-
Product
Peel Back Force Tester
PBFT
-
Precisely measure the peel back force of carrier tape to verify your packaging systems are within specification. Results can be printed and stored with the outgoing product.
-
Product
RJ45 Replacement Port For XG2 Tester
#TXGPORT
-
*Easy field replacement*RJ45 port installs with two screws*No wiring required
-
Product
Network, Port ID And Cable Tester
One for All PH-400
-
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
UV Accelerated Weathering Tester
TF424
-
TESTEX Testing Equipment Systems Ltd.
UV Accelerated Weathering Tester, age tester, to simulate the testing environment of sunlight, rain, and dew to reproduce the effect of sunlight with fluorescent ultraviolet lamps, providing rain and dew with condensing humidity. The aging of the specimens is accelerated by exposing the samples to alternating cycles of light and moisture at a certain temperature.
-
Product
LED Luminous Intensity Distribution Tester
LS860
-
LS860 Luminous Intensity Distribution Tester is a precise electronic instrument for measuring LED luminous intensity. It’s strictly designed according to LED standard requirements of CIE 127-1997 A or B Condition.
-
Product
Mini Fiber Tester (ST Type)
21-8681-00
-
The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.
-
Product
Voltage Testers
-
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
Product
Cable Continuity Tester, VGA Link Tester
72-9270
-
The 72-9270 is a VGA In-Line Signal Link Tester. Quickly test VGA connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
Product
Electrical Testers
-
Designed specifically for easy and intuitive use. After one minute, you’ll never again look at the directions. LCD displays exactly which measurement is being made. Audible beep confirms each measurement. Three distance memories and one calculation memory are maintained even when the unit is off. Calculator function permits addition/subtraction of readings.
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
COTS VME Board Tester
-
*Developed for support of Virginia Class Submarine at the COATS Integration Facility.*Provides Stimulus and Measurement Subsystem (SMS) to control, monitor, and evaluate VME assets used in the Non-Propulsion Electronic System (NPES) of the submarine.*Provides Native Environment Subsystem (NES) that simulates the operational configuration of typical NPES installations, and permits the test and evaluation of several types of VME assets.
-
Product
Flexural Damage Tester
DRK242A-II
-
Shandong Drick Instruments Co., Ltd.
It is used to test the dynamic anti-torsion and flexural fatigue performance of coated fabrics.
-
Product
Continuity Tester
26200
-
Just clip lead to one end of wire in question. Probe other end of wire. If bulb lights up, there is continuity. If bulb fails to light the circuit is open. Not to be used on live circuits or computer sensor feed circuits.
-
Product
Pro CABLE TESTER
PK-101/PK-101C
-
PK101 is an innovative tester to perform full cabling testing, displaying wiremap, cable ID, faults, toning and identify active network port on all common low-voltage cabling system in today's automated homes, network, telephone or video media, and determine cable run length up to 300 M.
-
Product
Digital Spring Tester 30N-500N
HT-30N~500N
-
Shenzhen Chuangxin Instruments Co., Ltd.
HT Series Digital Spring Tester is a special equipment to test the tensile and compressive deformation and the load of the spring characteristics.
-
Product
Automatic Battery/Electrical System Tester w/Cart
6044C
-
• Same features as the 6044 • PLUS heavy duty, two-wheel tilt-back cart with 8” wheels and 2 trays• Made in USA of US and Global Components
-
Product
6-12V Heavy Duty Circuit Tester
1650
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems. Use on accessories including lights, starters, alternators, cooling and heating components, radios and relays.
-
Product
Electrical Testers
-
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
Product
6-400V AC/DC Universal Voltage Tester
1998A
-
Peaceful Thriving Enterprise Co Ltd
This voltage tester is designed for industrial purposes which is suitable for voltage and current circuits.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Digital In-Circuit tester
MTS180/300
-
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
Product
In-Circuit Tester
IP-5000, IP-5300
-
The IP-5000 series is a space-saving high-speed board inspection device with a compact design.
-
Product
Polymer Testers
-
AMETEK Sensors, Test & Calibration
Accurate polymer testing requires dedicated polymer testing instruments. We offer a range of polymer testers for measuring density and intrinsic viscosity (IV).
-
Product
Hall Motor Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
