-
Product
Osram Direct Emission Green Laser Diodes (510 - 530nm)
-
The Optoelectronics Company Ltd
The PLT3 520D laser diode can deliver 140mW pulses at 520nm with 8% efficiency, driven at 300mA at 50% duty cycle – OSRAM's previous limit was 80mW with the PL 520B. This new diode has been developed to work in MEMS-based scanners.
-
Product
Battery Emulator And Profiler
E36731A
-
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
Photonics for Measuring Laser Output
Ray gt Photonic
-
raygt photonics for measuring laser output assist international research laboratories and laser technology manufacturers with precise positioning and output data.
-
Product
Laser Power Sensors
-
Make accurate laser power measurements, from the deep UV to the infrared, with these calibrated, traceable sensors.
-
Product
Extra Narrow Linewidth ECL Laser Module
NLTLS-XXXX-XX-PS
-
Narrow Linewidth ECL Laser Module series are high performance and industry-proven single frequency External Cavity Lasers (ECL) based on
-
Product
3U OpenVPX 3 Slot Profile BKP3-CEN03-15.3.5-3
1OVX303PZ6-1X11R
-
Single star FP data plane with two V66.4 optical slot interfaces.
-
Product
Low Profile PCI Express 8-Port
7803e
-
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Fiber Laser
ALiDAR Series
-
Amonics' high power fiber laser (ALiDAR) series offers eye-safe, single mode, linear polarized nanosecond-pulsed all fiber laser source with master-oscillator-power-amplifier.It is designed for three-dimensional imaging, wind detection and ranging LiDAR systems. The ALiDAR series is maintenance free with no post-installation service required. It is a versatile, ready-to-use and durable laser source for various LiDAR applications.
-
Product
3U OpenVPX 6 Slot Profile BKP3-CEN06-15.2.2-3
1OVX306UX6-1X11R
-
Single Star, expansion and control planes, 6.25 Gb/s.
-
Product
Pro Laser / Contact Tachometer
333
-
Dual function Laser Photo & Contact tachometer with 12 different measurement types. Laser method allows for longer detection distance, up to 6 feet away. Contact function adds distance and frequency measuring to the unit's capability.
-
Product
High Speed CO2 Laser Marker
LP-RC350
-
Panasonic Industrial Devices Sales Company of America
The LP-RC350 Series CO2 Laser Markers are best suited for high-speed applications.Features:- Compact Head Featuring IP54 Rating- Controller Offering High Resistance To Noise- Smart Condition Setting Function- High Speed "On The Fly" Direct Marking- 35-Watt CO2 Laser- High Resolution
-
Product
3D Laser Scanning Systems
-
3D laser scanning is a construction, engineering, and architectural tool often used to document the existing conditions (as-builts) of any structure.
-
Product
Laser Diffraction Particle Size Analyzer
SALD-2300
-
The new standard in the SALD series. While maintaining continuity and compatibility with respect to the data of the SALD2000/2100/2200, which were popular, widely distributed models, this instrument is equipped with many new functions useful for evaluating changes (dispersion, aggregation, dissolution) in particle size distribution relative to the concentration or time. It supports a particle concentration range from 0.1 ppm to 20% and can perform a series of measurements of 200 data points at 1 second minimum intervals.
-
Product
Laser Diode Modules: 635nm-660nm Visible Wavlength, Elliptical Beam
-
The Optoelectronics Company Ltd
Custom lasing wavelengths, from 405 nm to 852 nm, output power options and laser engraving are available to your specifications. Both standard and custom configurations provide OEMs, end-users and systems integrators with complete cost-effective laser solutions.
-
Product
Current Pulsers and Laser Diode Drivers (Pulsed Current)
-
These instruments generate current pulses whose amplitude is largely independent of the load voltage. This makes them ideal for pulsing device whose voltage may vary with time (for instance, the voltage drop of laser diodes may vary with temperature, or explosive squibs which change impedance during ignition). This voltage independence is a trade-off with speed. If faster rise times are required, consider using pulsed voltage instruments instead.
-
Product
Laser Tracker Tools And Accessories
-
MetrologyWorks provides a full line of Laser Tracker Accessories as well as Laser Tracker Tooling and Adapters. This includes Drift Nests, Permanent Monuments, Pin Nests, Edge Nests, Hidden Point Bars. If you need something custom we can provide custom Laser Tracker Tooling as well.
-
Product
Quantum Cascade Laser Module for OEM Customers
Mini-QCL™:
-
The Mini-QCL module is a miniaturized version of Block's LaserTune tunable QCL source, designed for OEM applications. Measuring approximately 1 cubic inch in size, each Mini-QCL module offers a 250 cm-1 tuning range. Modules are available within the same industry-leading tuning range as the full LaserTune instrument of 5.4 - 12.8 microns.
-
Product
Laser Sherography NDT Sensor for Post-Production Quality Control or In-Field Component Inspections
FlawExplorer
-
The FlawExplorer is a laser shearography NDT sensor designed to be used for post-production quality control applications or in-field (in-service) component inspections. Depending on the application, the sensor can be configured with thermal or vacuum (partial) excitation systems and may also be automated. It incorporates the very latest in phase-shifting technology delivering accurate and reliable measurement results through clear and sharp imaging with sub-micrometer displacement resolution.
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
Performance Profiler / Memory Leak Detector
GlowCode
-
GlowCode is a complete real-time performance and memory profiler for Windows and .NET programmers who develop applications with C++, C#, or any .NET Framework-compliant language. GlowCode helps programmers optimize application performance, with tools to detect memory leaks and resource flaws, isolate performance bottlenecks, profile and tune code, trace real-time program execution, ensure code coverage, isolate boxing errors, identify excessive memory usage, and find hyperactive and loitering objects.
-
Product
Femtosecond Terawatt Ti:sapphire Laser System
MPA-XL
-
MPA-XL is a cost-effective terawatt Ti: sapphire amplifier system. It gives up to 200 mJ energy of the stretched pulse and further compression with 65% efficiency. A standard air compressor can be placed into a custom designed vacuum chamber.
-
Product
Compact Infrared Thermometer With Laser Targeting
PIRT25
-
Unique Flat SurfaceMini-Modern Housing DesignSimple One-Handed OperationLaser TargetingLCD With BacklightCelsius or Fahrenheit ModesLaser On/Off SwitchAutomatic Power OffDisplay Hold FunctionMax/Min FunctionTemperature Range: -50 to 380 Celsius, -58 to 716 FahrenheitTemperature Resolution: 0.1Emissivity: Fixed at 0.95Optical Resolution: 8:1 Distance to Spot Size RatioBasic Accuracy: +2% of Reading or +2 C / +4 FResponse Time: <1 Sec.Diode Laser: Output <1mW @ 630-630nm, Class 11 LaserSpectral Response: 6-14umPower Supply: 9V BatteryDimensions: 7.09' H x 3.94' W x 1.81' DWeight: 5.6 oz.
-
Product
DB37F-DB37M LP, Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
154302-01
-
Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
-
Product
*Picosecond Lasers
-
A revolutionary laser technology due to its much shortened pulse duration of just 1012 seconds.
-
Product
Tunable Laser Source - MATRIQ
-
The Laser 1000 Series is a fully-compliant micro-ITLA laser with up to four channels in a compact benchtop form factor.Offering 0.01 pm resolution tunability across C or L bands, exceptional power accuracy up to 16.5dBm, and optional dither suppression, this is a versatile and cost-effective general purpose instrument.
-
Product
Short-distance, Wide-area Laser Sensor
LV-H65
-
Short-distance, Wide-area Laser Sensor. The area detection sensor enables stable detection, even when targets have variations in shape or surface condition. Built-in P.R.O. function. Coaxial construction
-
Product
*High Power Laser Beam Dumps & Low Power Beam Traps
-
Laser beam dumps for high power laser processing, laser measurement and other applications, and low power beam traps
-
Product
Optical Laser Source Products
-
Tunable Laser Source, Compact Tunable Laser Source, Fabry-Perot Laser Source Modules and Distributed Feedback Laser Source Modules.
-
Product
SF30/D High-speed Laser Rangefinder – 200 M
28062
-
sensor in the SF series. This 200 m sensor is known for its high speed, accuracy and performs well in even the most challenging conditions.
-
Product
Horizontal Profile Projector
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ The lifting system adopts cross roller rail and precision screw drive, which makes lifting drive more comfortable and stable;◆ Coating process reflector, clearer image and great dustproof;◆ Adjustable contour and surface illumination, to meet with difference workpiece demand;◆ Imported high light and long using life LED illumination ,to ensure precision measurement demand;◆ High resolution optical system with clear image and magnification error is less than 0.08%;◆ Powerful Bi-axial fan cooling system，highly increase using life;◆ Powerful and colorful DRO DP400，realized fast and accurate 2D Measurement;◆ Built-in Mini-printer, can print and save data;◆ With standard 10X objective, optional 5X,20X，50X，100X objective，rotary table, foot switch ,clamp, etc.
