Crimp
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp
510143002
Receiver Module Insert
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-FU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-015-2m-FU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 16A, 0.5m
40-972C-020-0.5m-FU
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Mating Coax Connector With 20 Coax Pins Crimped (One End) To 5 Foot Wires
GX96404-60
-
Mating Coax Connector with 20 Coax Pins crimped (one end) to 5' wires. Coaxial cable: RG316, 50 ohms.
-
Product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 1m, HV
40-972-009-1m-FU-HV
Cable Assembly
A range of 9 Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Micro and Milliohmmeter
AD-7110
-
The instrument AD-7110 is designed to measure, with high accuracy, resistance conductive elements of power devices: motor windings, transformer windings, conductor rails, inspecting the electrical conductivity of screw connections, crimp, welded state of the contacts of switches and relays current up to 100 A .
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 16A, 1m
A020GFR-C-1B100
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Connector, 50-Pin SGMC, Female, 5A, Crimp Pin, Without Backshell
C050FFX-1CP-0A
SGMC Female Connector
This 50-pin SGMC connector is designed to allow users to directly terminate with crimp connections and is suitable for 22 AWG copper wire. Supplied without a backshell. Screwlocks are provided to secure the connector to its associated product.
-
Product
Mating Coax Connector And 20 Coax Pins Crimped (One End) To 3 Foot Wires
GX96404
-
Mating Coax Connector and 20 Coax Pins Crimped (One End) to 3 Foot Wires
-
Product
20-Pin Scorpion Female Connector, 30A, With Backshell
C020AFR-2CP-3A
Scorpion Female Connector
This is a female 20-pin Scorpion Connector with crimp pins suitable for 10AWG cable. It is supplied with a rear cable entry backshell that includes screwlocks and cable clamp. The connector is keyed to position 2 and it has a maximum current handling of 30A and is suited for direct connection to Pickering Interfaces products.
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 0.5m
A020GMR-C-1B050
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 1m
40-972-037-1m-FU
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
50/75 Ohm Micro Coax Contacts
-
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
Product
Cable Assembly, 9-Pin D-Type, Male To Unterminated With Ferrules, 2m, HV
40-972-009-2m-MU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Signal Contact (ITA)
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Crimp Tester
M004
-
To calculate the crimp in yarn affected by knitting or weaving, to determine actual yarn usage.
-
Product
Cable Assembly, 26-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-026-1m-MU
Cable Assembly
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product
-
Product
Tool, Locator, TriPaddle, Receiver
910104127
Locator Tool
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
-
Product
Hand Crimp Tool For Scorpion Connector Pins
C020AFR-2CP-2A-O
Crimp Tool
Hand operated crimp tool for pins fitted into a Scorpion connector housing.
-
Product
Tool, Kit, 75 Ohm Coax, ITA, Cable Install
910102107
Tool Kit
Consists of 2 tools for installing cabling into the contact. Crimp Tool and Locator for center contact and Hex Crimp Tool for outer shield (p/n# 910104139).
-
Product
Tool, Locator, Thermocouple, Receiver
910104134
Locator Tool
Used with Crimp Tool Part # 910101102 to crimp thermocouple receiver contacts.
-
Product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Ferrules, 2m
40-972-009-2m-MU
Cable Assembly
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
20-Pin Scorpion Female Connector, 20A, With Backshell
C020AFR-2CP-2A
Scorpion Female Connector
This is a female 20-pin Scorpion Connector with crimp pins suitable for 14AWG cable. It is supplied with a rear cable entry backshell that includes screwlocks and cable clamp. The connector is keyed to position 1 and it has a maximum current handling of 20A and is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-037-0.5m-MU
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-015-0.5m-MU
Cable Assembly
The 15 Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 21 AWG Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Tool, Crimp Die, Coax, RG174 and RG316
910104117
Crimp Die
Tool, Crimp Die, Coax, RG174 and RG316
-
Product
Copper, Type T (°C) Contact
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
