RTD Simulation
calibrate resistance temperature detection systems.
-
Product
4 Channel Precision Resistance Simulator Card
DP-cPCI-2709
-
DP-cPCI-2709 RTD Simulator is ideal for applications of Resistance Temperature Detector(RTD) simulation requiring high resolution and low value resistances . DP-cPCI-2709 is offered in two factory selectable configurations of 4 channels and 2 channels depending on the resistance range needed. The 4 channel configuration offers resistance ranging from 30Wto 75Win steps of 50 mWresolution. This is ideal for applications where low Ohmic simulation is required. Similarly, the 2 resolution.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
-
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
LED Load Simulator
63110A/ 63113A/63115A
-
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
-
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
Product
Radar Target Simulator
E8707A
-
Rapid developments in the autonomous vehicle and demand for greater safety features is fueling the need for more sensitive and accurate automotive radar technology being deployed in advanced driver assistance systems (ADAS). With its rich expertise in radar test technology, Keysight now offers the E8707A radar target simulator to help automotive electronics manufacturers confidently simulate radar targets in various realistic scenarios.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel With V/I Readback
41-752A-011
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Battery Simulator Module
41-751-001
-
The 41-751 is a low power battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
4, 8, 16 And 32 ChannelARINC429 Test And Simulation Modulefor PCI Express
APE429-x
-
ARINC429 Test and Simulation modules with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s. The APE429-x is a functional replacement for the models API429-x/APX429-x.
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
VXI Synchro/Resolver Simulation & Measurement
65CS4
-
NAI’s 65CS4 is a Synchro/Resolver Simulation & Measurement Instrument on a single-slot VXI board. The board incorporates up to four Synchro/Resolver measurement channels and up to four instrument-grade Synchro/Resolver simulation channels, or up to eight embedded grade Synchro/Resolver simulation channels that can be used independently and/or simultaneously.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
43-670-103-AABBCC
-
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
Programmable S/R Standard & Simulator
5300
-
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.
-
Product
The ADAM-4115 6-Channel RTD Input Module Accepts A Wide Range Of RTD Sensor Types, Including Pt100, Pt1000, Ni50, Ni508, And Balco 500 Series.
ADAM-4115-B
-
Robust 6 channels RTD input moduleBroader operating temperature range: -40 ~ 85°CBroader power input Range: +10~+48 VDCHigher noise immunity: 4 kV surge protection on power inputs, 4 kV EFT, and ESD (8kV Air, 6kV contact) protectionOnline firmware update
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 24 Channel
41-761-002
-
The 41-761-002 is a low voltage 24-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI/PXI (3U)
ACXX429-3U-x
-
The ACXX429-3U-x is a functional replacement formodel ACX429-3U-x.
-
Product
Load Simulator
-
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCIe
APEX3910
-
STANAG3910/EFEX Test and Simulation module for PCIe with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APEX3910 is a functional replacementfor model APE3910.
-
Product
GNSS Signal Simulator
sUTP 5017
-
With the increasingly complex RF landscape, expectations for validation and functional testing of GNSS equipment are also rising. A large number of different navigation signals need to be reproduced under conditions that are as realistic as possible. The additional generation and injection of interference into the GNSS signals are supposed to simulate the real environment.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 2-Banks
43-670-003-AABBCC
-
The 41/43-670-003 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
Single Stream STANAG3910 Electrical Test & Simulation Module For 3U PXI Express/Compact PCI Express
ACE3910-3U-1-EN
-
Single Stream STANAG3910 Test and Simulation module – Rafale – for PXI Express/Compact PXI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE).
-
Product
PXI Millivolt Thermocouple Simulator Module - 24 Channel
41-760-002
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Module For PCI
APXX1553-x
-
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
PXI/PXIe Resolver Simulator Module, 4-Banks
43-670-201-AABBCC
-
The 41/43-670-201 is ideal for the simulation of Resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
CPCIe (PXIe) Module
ACS-FC-3U-2
-
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
41-670-103-AABBCC
-
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
VXI 16-Channel, 2-Wire LVDT/RVDT Simulation
65DL1
-
NAI’s 65DL1 is a 16-channel, 2-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board provides 16 independent, transformer-isolated, LVDT/RVDT, programmable 2-wire outputs (up to 34 V), wrap-around self-test, and an onboard programmable excitation supply.
-
Product
4, 8, 16, 32 Channel ARINC429 Test And Simulation Module For PCI
APXX429-x
-
ARINC429 Test and Simulation bus interface with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
-
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
-
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
