Dielectric Withstand Testers
check insulation to assure current does not flow through it.
See Also: Hipot, DC Hipot, AC/DC Hipot, Hipot Testers
-
product
Washing Fastness Tester
TF418E
TESTEX Testing Equipment Systems Ltd.
Washing Fastness Tester is mainly used to test the color fastness of textiles to washing or dry cleaning, i.e., the ability of textiles not to fade or change color after washing or dry cleaning.Washing Fastness Tester complies with AATCC 61, ISO105-C06/C10, etc.
-
product
Portable Hardness Tester
PHT-1800
State of the art, digital portable hardness tester is designed to test the hardness of large hard metal parts. Loaded with useful functions only found on high priced models the PHT-1800 portable hardness tester is clearly setting a new industry standard by being the most accurate, economically priced portable hardness tester on the market today.
-
product
LED Tester For Packaging Machine
LED-501 is a single crystal packing tester. It can be utilized in electrical test.Two test results. Pass (GO) or fail (NG).Electrical Testing: Forward：VF Reverse：VZ,IRFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Provide OPEN\SHORT count.Compatible mechanical interface.Connected with computer for measurement data collection.
-
product
Crease And Stiffness Tester
DRK153
Shandong Drick Instruments Co., Ltd.
Whether this is by hand or by mechanical means. The crease recovery (spring back) can result in forces, which distort the erected carton or cause stresses to be applied to closures, which reducetheir effectiveness. With the Crease and Stiffness Tester, the Crease recovery is determined by the decrease in resistance offered by creased board after it is folded 90° at the crease measuring the recovery force after 15 seconds. Board Stiffness is determined by bending a 50mm length of board through a 15° angle.
-
product
DIN Abrasion Tester
UI-FT24
DIN Abrasion Tester – DIN Abrader(Abraser) is a Rotary Drum Abrasion Tester of rubber testing instruments to test abrasion resistance of rubber, shoe sole. DIN abrasion test method meets ISO 4649, DIN 53516, ASTM D5963, SATRA TM174, and other abrasion resistance test method.
-
product
Pin Brinell Tester
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
product
AC Hipot Tester
295
Our Model 295 is a simple-to-use AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). You need a Hipot Tester that includes all the features you need to get the job done, the 295 has what you're looking for. Make testing simple with common sense security settings. PLC Remote allows you to make AC Hipot Testing safer with Personal Protective Equipment (PPE).
-
product
Multifunction Safety Testers
The new multifunction safety testers of the 1805 and 1886 series combine all the functions of their predecessors and expand them with many features that make your work considerably easier. This includes, for example, the new touch display. With this, all functions can be operated and at the same time the results can be read directly. Thanks to the interfaces available ex works, the 1805 and 1886 series can be easily integrated into your production line or operated "standalone".
-
product
Guardian Multi-Channel Hipot Tester
19020
Chroma Systems Solutions, Inc.
The Guardian 19020 enables users to save space on the production line since there is no need to purchase multiple Hipot testers. Its one time multi-channel test can increase the efficiency of electrical regulatory testing. It improves productivity and reduces the risks of testing for products that require only hipot testing.
-
product
SOLUBLE SALT TESTER
The PosiTector SST Soluble Salt Tester measures the concentration of soluble salts (salt contamination) on metal surfaces in accordance with ISO 8502-6, 8502-9. View Video
-
product
Fuel Injection Pressure Tester
33900
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
product
Low Impedance Voltage Tester
K-60
K-60 KNOPP VOLTAGE TESTER for AC and DC with polarity indicator. Double safety indication is by solenoid and by neon lamp. Knopp’s K-60 Low Impedance Voltage Tester (Cat. 14460) offers portability and ease of use with full protection. These exceptionally versatile and useful tools are backed by a reputation for quality in the design and manufacturing of electrical test equipment.
-
product
Rotation Field Testers
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. In normal use, the test leads are connected to the live terminals, with an R / L display showing the later direction of rotation of the electric motor. In addition, this model can be used for the contactless determination of the direction of rotation of switched-off or not connected motors. Place the switched-on measuring device on the motor parallel to the longitudinal axis without test leads. Now turn the shaft of the motor, the measuring device now shows a right or left movement.
-
product
Sefelec Harness Testers
Partech Systems Australia and SEFELEC France have formed a partnership to provide a more efficient service to our Australian Customers. Our common goal is to provide our customers with a total solution to cable testing and harness testing in the manufacturing and through life support realms.
-
product
LCR & Component Tester
PeakTech Prüf- und Messtechnik GmbH
Digital LCR measuring device for resistance, capacitance and inductance with high-resolution dual multifunction display. Components can be measured in series or in parallel and the LCR meter also offers the choice between automatic and manual range selection.
-
product
Rockwell Hardness Tester
Measures the permanent depth of indentation produced by a force/load on an indenter.
-
product
ADT-01 Primary Adhesive Tester
Jinan Leading Instruments Co., Ltd.
ADT-01 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Puncture Testers
Mechanical puncture testers check the puncture resistance or hardness of materials like dry wall, foam boards, cardboard, etc. They are ideal for handheld penetration tests or mounting to a test stand and intrinsically safe in hazardous environments. An optional handle is available.
-
product
Wrist Strap Tester
Statclean Technology (S) Pte Ltd
ESD wrist strap is most commonly used protective devices which prevent the build-up of electrostatic charge on personnel. The random failure of wrist strap compromises the protection. Thus, it is important to test every wrist strap regularly.
-
product
Cabin Leakage Tester
The Kanomax Cabin Leakage Tester pressurizes or depressurizes the automobile vehicle cabin to measure the changes in cabin pressure. The control unit consists of a manometer and pressure transducers. The manometer detects the leakage flow, which is calculated by measuring the nozzle pressure relative to static pressure. The tester controls an adjustable fan to maintain static test pressure.
-
product
Film Impact Tester
DRK136B
Shandong Drick Instruments Co., Ltd.
DRK136B Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
-
product
Electric Vehicle Battery Tester
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
product
Current Tester
MIG0624
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
product
Solenoid Valve Tester
DZ800
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
product
Universal Hardness Tester
Beijing TIME High Technology Ltd.
A single machine that combines multiple hardness testing methods, such as Rockwell, Brinell, Vickers, and Knoop, into one instrument.
-
product
Electrical Safety Testers
.AC/DC withstand voltage test & ground bond test .Insulation resistance test(ST60).Arc detection.Zero crossing turn-on,turn-off operation switch.Controllable ramp-up time .Ture RMS cut-off current measurement .Automatic fail indicator of alarm lamp and buzzer.VFD display.Standard PLC interface .Option RS-232,RS-485
-
product
Hydraulic Adhesion Testers
108
The Elcometer 108 adhesion tester is the ideal gauge for testing coatings on tanks, pipelines, etc.Hand-Powered and portable adhesion testerIdeal for site workReusable stainless steel dolliesElcometer Digital Adhesion Tester features:Maximum hold - displays the highest value reachedBacklit display for dark areasRubber protective casingSwitchable Metric/Imperial units.
-
product
Paper Softness Tester ZRD-T1
The ZRD-T1 Paper Softness Tester is a device designed to objectively measure the softness of paper products, such as tissues, toilet paper, or specialty papers. Softness is a complex tactile property influenced by factors like surface smoothness, flexibility, and bulk compressibility. It is widely used in industries such as tissue manufacturing, hygiene product development, textiles, and packaging to ensure compliance with quality standards and end-user comfort requirements. This test instrument conforms to many national and international standards: ASTM D2923: Standard Test Method for Rigidity of Paper – Measures bending resistance to determine stiffness. ASTM D6828: Standard Test Method for Stiffness of Nonwoven Fabrics – Evaluates drape and flexibility in materials like medical textiles or wipes. TAPPI T498: Bending Resistance of Paper (Gurley Method) – Quantifies resistance to bending forces, inversely related to softness. GB/T 8942: Chinese Standard for Softness Testing of Household Paper – Aligns with consumer expectations for tissue and toilet paper tactile quality. ISO 12625-9: Softness Evaluation of Tissue Products (optional add-on).
-
product
Vibration Testers
Guangzhou Amittari Instruments Co.Ltd
The Vibration Tester can display the parameters of “Displacement”, “Velocity” and “Acceleration” simultaneously; Applied to the periodic motion measurements to detect moving mechanical imbalances and misaligned. Designed for on-site measuring various mechanical vibration, for quality control, running time and prior equipment maintenance data. Selection of high-performance accelerometers to achieve accurate, replicable measurement It has a bearing condition measurement function.
