DC Current Clamps
-
Product
C/I Clamp Meters
CLAMPMETER, 400A AC (CM-410)
-
*Measures to 600 volts AC and DC, and 400 amps AC*Data hold to capture important readings*Audible continuity test*Auto power off for longer battery life*Accessories included: (2) 1.5V AAA batteries, test leads, carrying case*Lifetime Limited Warranty
-
Product
Multiport Coaxial Switch, DC to 26.5 GHz, SP6T
87106C
-
The Keysight 87106C multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87106C terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
-
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
Digital AC/DC Clamp Meter (with NCV Detection)
3812 CL
-
Standard Electric Works Co., Ltd
● Full Autoranging for V, A and Ω functions.● Data Hold function freezes reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Auto-zero / REL function.● Non-contact voltage detection.● Auto power off.
-
Product
Current Measurement Board
MS 1814
-
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
Product
AC/DC Current Probe (2-Channel), 3 MHz, 50 UA
N2820A
-
The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time.
-
Product
DC Electronic Load
3310G Series（75W~400W）
-
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
Digital DC Micro Volt meter
-
PGP Electronics Private Limited
PGP Electronics Digital DC Micro Voltmeter is a precision measuring tool for the measurement of low DC Voltages. This unit can measure low DC voltages, typically in the order of Micro Volts. This instrument is designed to with stand rugged operation.
-
Product
AC Clamp Meters
-
Cambridge Instruments & Engineering Co.
A clamp meter is a clothespin-shaped instrument that can be clamped around a live wire in order to measure the current it's carrying. As a measurement principle, clamp meters detect the magnetic field emitted by current flowing in a wire in order to measure the current value.
-
Product
Scienlab Regenerative DC Emulator
SL1800A Series
-
Keysight's SL1800A Scienlab Regenerative DC Emulator - High-Power Series enables users to emulate the large batteries in electric vehicles. The bidirectional power flow allows emulation of both power sourcing applications, such as traction inverter test, as well as power-absorbing (sinking) applications, such as EV charging. Being regenerative, the power absorbed is delivered back to the grid, saving on energy and cooling costs. The SL1800A Series is fully integrated with the SL1040A Scienlab Charging Discovery System. The SL1093A Scienlab Charging Discover Software fully automates DC charging applications to many different test standards. With bi-directionality, integrated DC voltage and current controllers, high dynamics, and its regenerative energy feedback capacity, the Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
Product
1000 Amp AC/DC Digital Clamp Meter
DL6402
-
With inclusion of DC current temperature & capacitance readings, this clamp meter is the ideal all purpose instrument.The slim design combined with the tear shaped jaw makes it an ideal unit for use in crowded panels and tight spaces.The data hold and peak capture function makes this a versatile and cost effective clamp meter.
-
Product
Multimeter Clamps
-
The ideal tool for detecting and measuring the leakage currents flowing to earth.The versatile clamp also offers all the functions of a multimeter clamp.In addition, the clamp is equipped with an RMS converter to ensure that the measurements remain accurate even in the presence of distorted signals.
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
True RMS Clamp Meter w/ ATTPC3
DL389BCOMBO
-
UEi Test & Measurement Instruments
True RMS Dual Display Clamp Meter w/ Temperature and ATTPC3
-
Product
Dual DC Electronic Load
3330F Series（40W~250W）
-
3330F Series Dual DC Electronic Load is a two load unit in one module. Each 3330F Series module has its own control and display panel, CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be remote controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
DC Switching Power Supply
-
Power Source : Wide Input(90V to 260V~) 50Hz/60Hz Output Current : 0~3A, 1A(Fixed) Rs-232C Interface(Option) Programmable(Option)
-
Product
IP67 DC Blocking L-Band Splitter
PD5021
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portOutdoor Weatherproof ConstructionTri Alloy N Type Female (Jack) 50 Ohm
-
Product
High Current Triaxial Cable, 4 A, VOLT:DC 60V
PX0104A
-
The Keysight PX0104A is suitable for high current measurement up to 4 A DC. It supports the Keysight M9602/03A.
-
Product
Miniature AC & DC Voltmeters
PM Series
-
The PM Series Full-functioned miniature digital voltmeters are AC or DC reading, and feature AC or DC power options, and LED or LCD displays. These versatile meters are available in 100mV, 200mV, 1V, 2V, 10V, 20V, 100V, 200V, or 1000V ranges. Highly accurate (up to 0.02% of full scale), with rapid update rates (up to three reading per second), these meters feature bipolarity (PM-3 is unipolar), a presettable decimal point, overload indication, an extensive list of application-specific options, and easy installation.
-
Product
Logger version 2-D electro-magnetic current meter
INFINITY-EM AEM-USB
-
Infinity EM is an autonomously deployable EM (electro-magnetic) current meter with a data logger. Due to the principle, the instrument provides high accurate 2-D current measurements in even low scatter fields, where ADVs (Acoustic Doppler Velocimeter) has difficulties. The measurement range is wide from 0 to ± 500 cm s-1. The instrument design is compact (1.0kg in air). Infinity EM allows for current velocity measurements virtually anywhere.
-
Product
Eddy Current Testing /ET System
-
Xiamen IDEA Electronic Technology Co., Ltd.
Eddy current testing system uses the most advanced digital electronic technology, photovoltaic technology and microprocessor technology. With beautiful design automatic transmission, complete electromechanical integration system, which is the only company that have a complete system of automatic machine.
-
-
Product
Regenerative Power System 1000 V, ±90 A, 30 KW, 400/480 VAC
RP7982A
-
The RP7982A regenerative power system is a single output, bi-directional, regenerative DC power supply with safety features to protect your people and your DUT.
-
Product
Portable DC Power Supply
PS 30-20
-
Laxtronics Instruments & Controls Pvt. Ltd
Input Voltage 220 V, 50 HZ, 1 PH.
-
Product
SparkFun Current Sensor Breakout
ACS723
-
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
Current Measurements of PWM or Inverter, AC/DC 10～200A, φ24mm
CTF-200DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
