AC Current Clamps
wrap around conductors to measure current.
-
Product
Direct Current Measurement Card
LQI5
-
Computer Gesteuerte Systeme GmbH
The LQI5 is a precision direct current measurement card. It features 6 measurement ranges for unipolar current measurements of up to 32 A. Current pulses shorter than 5 seconds can be measured up to 65 A.
-
Product
Power Monitor, AC- or DC-Powered
109
Power Monitor
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
Product
AC Power Source
LSP-500VAR
-
• AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCU • Protection for over hot, thundering voltage and current • Total voltage distortion: ≤0.3%; Voltage stability: ≤0.05%/30min • Load adjust rate: ≤0.05%; Frequency stability: ≤0.01%/30min • Output voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400Hz • It is pure sine wave AC power source with low harmonic and high accuracy • Input Power: 220V and 50/60Hz (110V can be option) • Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
Product
Secondary Current Injection Test Sets
-
Our range of units covers applications up to 200A and includes single phase and three phase units with applications for testing and timing of IDMT relays, thermal overloads, MCB’s and auto-reclosers.
-
Product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
Current Output Module
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
-
Product
10-amp AC and DC Variable Power Supply
ACDC-10
-
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
Product
16-Ch SPST 10A-277VAC High Current
YAV90086
Switch Module
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
AC High Voltage Test Sets
-
We are highly reckoned among clients for manufacturing and exporting an excellent AC High Voltage Test Set. It is specially engineered and developed for performing varied tests on air conditioner. As to satisfy clients' requirements, we can also optimize this test set. Manufactured in accordance with industry standards using supreme grade raw materials, this AC High Voltage Test Set is offered to clients at industry leading price. Before the final dispatch in market, this test set is stringently tested on varied quality parameters.
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-500IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
Product
Portable AC Chassis Dynamometer
TD-24-AC-T
-
The TD-24-AC-T is a self-contained, portable, motorized, Chassis Dynamometer specifically designed for testing Over-the-Highway (OTH) trucks. Rated to test at altitudes up to 10,000 ft (3,048 m), the TD-24-AC-T is road-legal and offers side loading with ramps. The Portable AC Chassis Dynamometer takes less than 60 minutes to set up and begin testing.
-
Product
Hall Effect DC Current Sensor
CYHCT-L20K
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
High Accuracy AC Reference Source
515
-
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
Product
High Current Electronic Load (600W-1200W)
ELCH600 & ELCH1200
-
- Low lead resistance <5m Ohm for Fuel-cell- Battery Testing- VFD display- High resolution 0.1mA/1mV- Voltage range 0V to 500V- Working mode CV/CC/CW/CR- OV/OC/OP/OT protection- Communication: USB/RS232/GPIB
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
AC Engine Dynamometer
DA100
-
Power: 100 hp (74.6 kW)Torque: 175 lb-ft (237.3 Nm)Maximum Speed: 8,500 rpmConstant Torque Range: 0 - 3,000 rpmConstant Power Range: 3,000 - 5,100 rpmDecreasing Power Range: 5,100 - 8,500 rpmRotation: bi-directional
-
Product
Electric Vehicle AC Charging Compatibility ATS
8000
-
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements
-
Product
1000 Amp AC/DC Inductive Amp Clamp
6043
-
• A great tool for accurate measurement of current sources up to 1000 amps• Use with most digital multi-meters• 1mV/Amp output guarantees easy reading on your meter• Ideal for checking starter draw, alternator output or parasitic battery drain testing• Design allows accurate current readings without breaking the circuit• Low battery indication – auto power-off• Switch settings OFF/200A/1000A• Large jaw opening, 2.2″ and large jaw space, 2.2″ x 2.75″• Imported
-
Product
Current Calibrators
-
Used for basic measurements, tests and regulation techniques for setting and verifying test installations and instrumentation.
-
Product
30A Auto Current & Voltage Tester
7610A
-
Peaceful Thriving Enterprise Co Ltd
*Fast, accurate and safety current measurement from the fuse box.*Feature with large LCD display and mini/ATO fuse probe.*Ideal for diagnostic of vehicle's electrical circuits.*With CE Approval.
-
Product
AC Reference Generators
SR25
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Through Hole type AC Current Sensor
CT-6K
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Power Clamp Meters
-
TES Electrical Electronic Corp.
Communication with PC. 4000 continuity point data logger, 25 point manual data logger. True power/ apparent Power/ Power Fractor Measurement. True RMS. V,A,W cap Ind, phase indicator.
-
Product
Clamp Meter 6000counts Ture RMS
VA312 /VA315
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter Diode Test Auto Range Continuity Buzzer MAX/MIN Value Measurement.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
-
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
Current Probe
PA-659
-
*Maximum Current Value: +/- 150ADC, 100A RMS*1mA = 5mA, 50mA (switchable)*Rising Time: 0.7uS*Bandwidth: DC ~ 500kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
DC Earth Leakage Current Measurement
DCZCT-11M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC Earth Leakage Current Measurement *Bipolar DC ±12V Power Supply*Output DC ±1.5V at DC 10mA *Isolated Housing Case based on UL94V-0*Through Hole PCB Mount Type, Exciting Current Method
