Socket Testers
test access viability to electricity, gas or data.
-
Product
Folding Tester
FOT-01
-
Jinan Leading Instruments Co., Ltd.
FOT-01 Folding Testeris designed according to relevant standards and adopts modern mechanicalphilosophy and computer processing technology. Folding tester complies with relevant standard. It is suitable to test fatigue strength of paper, paperboardand other sheet material, which thickness is less than 1mm.
-
Product
Continuity Testers
-
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
-
Product
Condensation Tester
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Condensation tester simulates the damaging effects of outdoor moisture attack by condensing warm water directly onto test specimens. In a few days or weeks, the tester can reproduce the damage due to moisture that occurs over months or years outdoors.
-
Product
Motor/Generator Testers
-
Appliance motors are always evolving and the final testing of those motors gets more complicated every year. We build fully automated testers for domestic or offshore manufacturing facilities that can perform any amount of motor testing that you require with limited interaction by the operator.
-
Product
Solderability Tester
MUST 3
-
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
Product
Hardness Testers
-
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
-
-
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Leak Tester
AD-1690
-
Are you sure your pipettes are all accurate? Most pipette failures happen due to soiled or damaged parts compromising the airtightness of the pipettes. With the AD-1690 leak tester, you can instantly spot the pipettes that need to be fixed.
-
Product
Functional Tester
ESF-2003
-
The functional tester developed on the basis of our experiences in electric parameters testing technique.Accumulated with 30 years of experiences in electronic testing, Shindenshi Corporation develops this ESF-2003.Shindenshi will provide suitable products to customer for their need.
-
Product
Conductivity Tester
EC
-
Monitor conductivity levels quickly and easily with Series EC Conductivity Testers. These pocket-sized testers are ideal for conductivity measurement in the lab, industrial plant or out in the field. Series EC measures conductivity from 0 to 1990 microhms (S) or 0 to 19.90 milliohms (mS).
-
Product
Hydrostatic Testers
-
Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 30 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07. In addition to U.S. Military stock listed hydrostatic testers, we manufacture both standard and custom hose proof test stands, portable hydrostatic testers, hydrostatic test chambers and ancillary equipment to fit individual customers’ needs as required. We can typically ship standard units within 24-72 hours, sooner if required.
-
Product
Multi-purpose Tester
DEL-101
-
Standard Electric Works Co., Ltd
Mains wiring polarity check. ELCB/RCD testing. Measuring ear for line current. Measuring ear for leakage current. Helps calculate insulation resistance. Helps calculate power consumption. Helps fault finding of standing earth fault. Fused main adapter. Appliance testing (with the aid of a clamp meter). Fused appliance socket. No batteries required. HRC fuse inside. Fused, color-coded universal test sockets. Universal mains IEC Lead.
-
Product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
-
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
Product
Dissolution Testers
-
Dissolution testers have wide application in Pharmaceutical Industry, for detecting velocity and extent rate of dissolution i.e. solution formation from a dosage form like tablet, capsule, and ointment, etc. across manufacturing plants, research centres.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
-
Product
Low Distortion 1kW Power Source With UK/Schuko/USA Socket.
AC1000A
-
Provides an EN61000–3–2 compliant source1000W power capability at 230VUp to 4·4A rms load current and up to 10A peak currentsComprehensive overload protectionConnection via standard power connectors
-
Product
Probecard testers
MANAGER
-
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
Product
Bond Tester
Sigma Lite
-
Sigma lite is a low cost of ownership bond tester that grows with your company. It gives you a low-cost entry point without sacrificing performance to meet future demands.
-
Product
CT Tester
6000 Bird Dog Plus
-
Spinlab Utility Instrumentation, Inc.
This new and exciting true 3 phase Bird Dog Plus enables you to determine the accuracy of any meter in the field--from Form 1 through Form 17. Electronic sensors allow you to automate the test to gain the highest possible accuracy. The process is fast, simple, and much less expensive than a portable test board for the meter test and still perform ratio & burden tests on your CTs (CT Tester).
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Voltage/Continuity Tester
VOT-52
-
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Battery/Alternator Tester
BT55U
-
Schumacher Electric Corporation
BATTERY/ALTERNATOR TESTERFOR TESTING:• Battery state of charge• Charging system outputFEATURES:• Accurate, easy-to-read LCD screen.• Checks the battery, alternator systems• Two LED indicators• Overvoltage and Reverse Polarity Protection Contents: (1) Battery/Alternator Tester
