Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 239
40-297-013
Programmable Resistor Module
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Steady State Solar Simulator
-
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
Product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
Carrier Board
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
Product
Software to Simulate Large Area Semiconductor Devices
Laoss
-
Laoss is a powerful software to simulate large area semiconductor devices (OLED, thin-film PV), taking into account the voltage drop in the electrodes due to important resistive effects when the size of the device increases.Simulation of large area semiconductor devices (OLED, thin-film PV)Coupling law input: analytical or tabulated (experimental or simulated) IV curveDevice optimization (electrode material, device geometry etc...)High speed computation
-
Product
R + D Testing of Electric Motors
-
Highly dynamic development test bench for synchronous and asynchronous motors*Comfortable concept with changeable test angles for handling various load machines and test pieces*Freely configurable test runs - ie suitable for endurance tests and long-term examinations*Equipped for environmental simulations (temperature)*Examination of complete drive systems (motor and inverter)
-
Product
PXI Precision Resistor Module 2-channel 1.5 to 2.9k
40-261-001
Programmable Resistor Module
PXI programmable resistors featuring fine resistance setting resolution and excellent resistance stability and accuracy through the use of advanced switching networks and software correction techniques. The two modules in this range support two identical resistor channels t that can be set to values of between 1.5Ω to 2.9kΩ or 10Ω to 36kΩ with a precision of better than 2mΩ (this version) or 15mΩ (40-261-002) making them ideal for simulating sensors that can be accurately controlled to fine values.
-
Product
Rapid Decompression Test Chambers
CA-RD(H)
-
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
Product
IEC60068-2-75 Spring Hammer Test
CX-T03
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Impact hammers are used to check the durability of enclosures for electrical appliances of other electronic products.If damage occurs from the Impact Hammer test .Accessibility probes can be used to measure the extent or severity of the damage.The Impact Hammer simulates the mechanical impact to which electrical equipment may be subjected. *This hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.* The impact tester made of stainless steel or alloy.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
Portable Testing Kit for Gulfstream Aircraft
ES-429TK-101
-
The ES-429TK-101 Portable Testing Kit (for Gulfstream aircraft) enables you to simulate Airspeed, Altitude and Radio Height values over an ARINC 429 bus. The ES-429TK-101 Portable Testing Kit consists of a DAS-429UNET/RT10, battery and the Exc429Tester application that runs on the host computer, a laptop or desktop PC running Windows. Using the ES- 429TK-101 Portable Testing Kit with a laptop provides a portable testing system.
-
-
Product
Software for Test, Analysis and Simulation applications
AIM Software Solutions
-
AIM offers PBA.pro Software for Test, Analysis and Simulation applications. PBA.pro is compatible with Windows and LINUX Operating Systems and supports most of the AIM interface hardware modules. The flexible, scalable and open PBA.pro concept supports a wide spectrum of customer applications.
-
Product
Reference Cells For PIV-IV Systems
-
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
Product
Multi-Channel PCM Processing and Recording System with UDP Streaming
LS-68-M
-
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Physiology / Altitude Testing Rooms
-
Darwin Chambers Company has teamed up with Colorado Altitude Training (CAT), located in Boulder, Colorado, to offer a unique chamber for altitude simulation. CAT advances altitude simulation technology by maintaining the largest research and development division in the industry. CAT has invested heavily in technology and research to maximize comfort.A CAT system can reduce the oxygen content from 20.9% to 15.2% to simulate 9,000 feet at sea level, while keeping the pressure unchanged. Whether at real altitude, in a hypobaric chamber, or in an environmental room/CAT system, the amount of inspired oxygen and physiological effects are the same.
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
Artificial Skies
-
As a simulator maker, we can say the artificial sky, among other devices, is the ideal instrument for every lighting designer and lighting engineer. In fact, to predict daylight penetration inside a building, a scaled model under an artificial sky is the only reliable prediction method in the case of unusual situations, complex geometries, or heavily obstructed windows.
-
Product
Automatic Upset Testing Machine
YQA Series
-
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
Product
Bending Drain
-
With the Bending Drain you measure the shrinkage and bending of building materials. Also you may simulate with a built in electrical heating a real world floor heating.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel, 1 Ω to 61 Ω
40-297A-111
Programmable Resistor Module
The 40-297A-111 (PXI) and the 42-297A-111 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 61 Ω, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Welding Simulator
-
High-speed, direct resistance heating up to 10,000C/secondControlled cooling or accelerated cooling with optional quench (air/gas/water/mist)Simulation of multiple welding techniques and materialsAbility to test in vacuum, air or inert gasEasy to use controls and software, including DSI's custom Gleeble Welding Software
-
Product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Modules
ACXX1553-3U-x
-
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation modules for CompactPCI/PXI (3U).The ACXX1553-3U-x is a functional replacement for model ACX1553-3U-x.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 3.55kΩ
50-297-123
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
68HC11D Simulator
SIM11D
-
Simulate your M68HC11 microcontroller designs on your personal computer. Helps find hidden errors easily and efficiently.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
The Imperas Instruction Set Simulator
ISS
-
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
Product
Fiber Channel Simulyzer
-
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
