Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
Analog Output Module
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 102k
40-297-040
Programmable Resistor Modules
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
43-752A-903
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
Interface
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
NIBP Simulator
vPad-BP
-
vPad-BP, part of the vPad-A1 family, is a NIBP (non invasive blood pressure) simulator designed to test the accuracy and repeatability of the NIBP function on Patient Monitors. User programmable settings allow for easy on site configuration to accommodate new models of NIBP devices.
-
Product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
LIN Interface
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 2K
40-265-302
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Avionics Supply Simulation System
-
Spitzenberger & Spies GmbH & Co. KG
Simulation of voltage variations. Simulation of frequency variations. Creation of practical disruptions
-
Product
Fiber Channel Simulyzer
-
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Grid Simulator
PAS-F
-
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Product
The Leading Measurement System for the Analysis of Porous Materials
ELWIS
-
ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.
-
Product
CAE Software
Femtet
-
Femtet is the simulation software based on the finite element method. It solves 8 physical phenomena (electric field, magnetic field, electromagnetism, mechanical stress, thermal conductivity, fluid, acoustic waves, and piezoelectricity). Multiphysics between the solvers are available as well. Its extensive functions include modeling, automatic meshing, and results display.
-
Product
Hybrid Vehicle Battery Simulator and Test System
-
Winner of the SAE 2008 Technical Award for Hybrid Vehicle Testing Technology, SAKOR Technologies Hybrid Vehicle Battery Simulator and Test System is designed for simulating high-voltage batteries in an electric drivetrain testing environment as well as directly testing high-voltage batteries and charging systems.
-
Product
Weather
-
A laboratory instrument that simulates the degrading effects of outdoor environments—like sunlight, rain, and dew—on materials to predict how they will hold up over years of real-world use.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 62.1Ω
50-298-011
Programmable Resistor Modules
The 50-298-011 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 62.1Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Cloud Service
Insight
-
Insight cloud service further empowers architects and integrated design teams with centralized access to building performance analysis data and advanced simulation engines.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 3Ω to 6.97kΩ
40-298-030
Programmable Resistor Modules
The 40-298-030 is a high density programmable resistor module with 9 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
LIN Interface Module
C Series LIN
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 26.7kΩ
50-298-132
Programmable Resistor Modules
The 50-298-132 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI RTD Simulator Module, 20 Channel, PT1000
40-263-103
Simulator
The 40-263-103 is a 20-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SignalHawk I/O Cards
-
Concurrent Real-Time’s SignalHawk I/O delivers ultra high-performance PCIe I/O cards designed for precision data acquisition, signal processing, and advanced simulation applications.
-
Product
Recloser Control Analyzer
GEN-I3V
-
The GEN-I3V is a universal analyzer for Recloser Controls and a Recloser Simulator of up to 15 Amps. In addition to current injection up to 15A, it also supplies 3 voltage sources to perform a complete range of testing and provides high precision curves in no more than 10 minutes.
-
Product
2 PRI + 4 Port FXS PSTN Simulator Adv
CH-4FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
Compliance Testing
-
American Environments Co., Inc.
The American Environments Company, Inc. (AECO) provides comprehensive compliance testing services. Our laboratory is fully equipped to provide Electromagnetic Testing, Environmental Simulation Testing and Dynamic Testing. Compliance requirements are related to the marketplace being serviced. AECO provides compliance services for: Products Exported to Europe, FCC, Telephone Network Equipment and Medical Devices.
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
