Filter Results By:
Products
Applications
Manufacturers
-
product
Digital (1kV below) Insulation Tester
1160 IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
product
Analogue (1kV below) Insulation Tester
1652 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
product
Analogue (1kV below) Insulation Tester
4132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
-
product
12-24V Multi-functional Auto Tester With LCD Display
6511
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
AMP HOUND 2
AMP2
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
product
HV AC Test Set
SERIES S400 TYPE RX I O/ I OACP
K&S Engineering and Scientific Ltd
The output is continuously variable from zero to 10 kV by means of the panel mounted regulator. An output trip is fitted which operates when the output exceeds 25 mA switches off the test set and operates a neon overload indicator. Primary protection is provided by two panel mounted fuses. The output is protected by the output trip and a magnetic/hydraulic circuit breaker.
-
product
Digital RCD Tester
1113 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Very low consumption.● 50Hz and 60Hz operation.● Accurate digital readout of disconnection time.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Auto power off. ● Backlight function. ● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Digital Multimeter
6420 DM
Standard Electric Works Co., Ltd
● 4000 counts LCD with a maximum display of 3999.● Angled display design helps the user to identify the reading of value easier.● Auto ranging designed.● Bar graph LCD display.● Range change function.● Relative/Maximum/Minimum modes.● Peak hold mode.● VAHz mode measures frequency in voltage or current mode.● 40M Hz frequency counter.● Auto Power off.● Continuity check.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.
-
product
LCD Display Battery Monitor
TE6-0609
Hangzhou Tonny Electric & Tools Co., Ltd.
*Plug into a standard 12V/24V power outlet*Two USB outlets for charging 1x standard 1A and 1xhigh *output 2.4A*Voltage is displayed by digital read out to indicate battery*charge level*Flashing LED alarm and warning audible sounder indicates*low battery voltage*Replaceable 3A fuse*Suitable for 12V negative earth systems*Adjustable main plug angle*Ideal for the vehicle that double as a mobile office
-
product
FS1 FUSE
FS1MAFUSE
*0.63A/500V AC IR50kA (6 x 32mm) fuse for MD251 and MD257 digital multimeters
-
product
Splicers And Cleavers
Uses active cladding alignment technology which allows the technician to reliably fuse fiber optic cables with low splice losses.
-
product
Digital RCD Tester
1112 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Very low consumption.● 50Hz and 60Hz operation.● Accurate digital readout of disconnection time.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Auto power off. ● Backlight function. ● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Continuity Tester
1670
Peaceful Thriving Enterprise Co Ltd
1. For automotive, marine, aircraft and home appliances. 2. Detect open circuit in fuses, diodes, switches, sockets and wires.
-
product
Low Resistance Ohm Meters
DMO-100D
For fast and accurate measurements of low resistanceon Switch Contacts, SF-6 Switch Gear, Bushbars, Splices, Joints, Fuses, Breaker Contacts, and Rail Bonds. • 100A DC continuous current in 4 ranges of 10A, 20A, 50A and 100A
-
product
Super Energizer 5
SE-5
Parker McCrory Manufacturing Co.
A powerful model designed for today`s large pastures. Ideal for single or multi-wired high tensile fences. The Super Energizer 5 does everything a fence controller should do – it just does it better!!! Super Energizer 5 is equipped with a built-in DIGITAL performance meter which tells you the exact condition of fence. Shocks through wet weeds and brush. Over 8,000 volts of holding power with 500 OHM load. New color coded fence and ground terminals. Red to the fence and Black to ground. The Super Energizer 5 controls both predators and livestock, including sheep and goats. Fuse protection with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
Circuit Tester
69105
Tests circuits rated from 80 to 600 volts AC/DC.High-visibility neon lamp indicator.High-impact, sealed 5-11/16'' (144 mm) probes on long 24'' (610 mm) leads for convenience in testing motors, fuses, relays, switches, etc.Resistor between each probe and lead.Reliable electronic components.
-
product
Fuse Circuit Breaker and Fault Finder
Shanghai Beha Electronics Co., Ltd.
*is a Fuse and Fault Finder which comprises of two parts: The Receiver and the Transmitter.*Locating and tracing of cables*Finding Circuit Breaker/RCD
-
product
Parasitic Drain Tester
64970
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
-
product
12V Electrical Continuity Tester
1924
Peaceful Thriving Enterprise Co Ltd
*Check on 12V systems. *Quickly check continuity of dead circuit, sockets, door bells, motors, switches, fuses and other high voltage appliances.
-
product
6000 count Wireless Connectivity Digital Multimeter with replaceable fuse and data connect to Smart phone
MS-WM86
This is a compact, mini size, external wireless connectivity Digital Multimeter integrated with 6000 Count, True RMS auto and manual measurement.
-
product
Leaking Current Meter
7610B
Peaceful Thriving Enterprise Co Ltd
This is a stable, low power consumption, and high accuracy 3 1/2 digits (2000 counts) leaking current tester for automobile. Leaking current for automobile is generally as small as milliamps, which is hard to measure by clamp meter. By plug this meter with the fuse box, user is able to measure leaking current as small as 1 mA.
-
product
30 Amp Fuse Buddy
305M
*Fuse Buddy Testers can test circuit current up to 30 Amps. *Two 30 Amp models, #305M used with Mini size fuses and #306B used with ATC size fuses. *Blowing fuses? Get the Fuse Buddy, a great new product. *Clever design allows for easy connection into fuse sockets. *30 Amp models have resolution of .1A, while 20 Amp models have .01A resolution. *Fuse Buddy ends are molded into the shape of the fuse itself. *During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. *The Fuse Buddy stays put and won't fall out of the socket, like test probes do. 305M & 306B Specifications *Tests circuit current from 0 to 30 Amps/48 Volts *Resolution .1A (100 milliamps), accuracy + 2%
-
product
Transformer/Capacitor Test Sets
*Quick and easy check for opens or shorts on transformers or capacitors before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers as well as capacitors and capacitor banks*Tests the primary and secondary sides of de-energized transformers and capacitors without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer or capacitor*Automatic self-test featureMagnet holds the tester in place while testing
-
product
Hot Sticks
HS-120
Standard Electric Works Co., Ltd
● Used for the extraction of fuses, isolators & fuse switch disconnections.● Can be attached to the 275 HP Proximity Detectors and contact Capacitive Detectors 21× HVD.● Universal "sunrise" head attachment to fit special tool fittings.● Head Section rated at 100kV per 300mm (5 min).● Comes complete with sunrise fitting and fuse extractor.● 3 × 1.8 meter sticks; 1 × 1.2 meter head section.● Sticks 1 × 1.2 meter head section complete with universal sunrise fitting. ● 1 × carry bag. ● Meets IEC 60855.
-
product
Enlarge Environmental Chamber
REXMED REC-250
MOD. REC-250, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Power Factor Correction
HV/MV
Power Capacitors for medium voltage network:Ducati Energia proposal includes range of single and three-phase capacitors up to 800 kVAr with max HSV of 36kV.Upon request,we provide them with internal fuses stainless steel cases,inrush reactors,expulsion fuses as well.System is designed according to the specific application and it is composed by current transformers (CT),voltage transformers (VT) and relais.
-
product
Analog Insulation Tester
SAIT200
Over voltage CAT. 600V. Battery operated. Solid state circuitry. Automatic circuit discharge. Color coded scale. Fuse protected : Fast blow 0.5A 250V
-
product
Fusion Splicer
Shaanxi Aitelong Technology Co., Ltd
Fusion splicing is the act of joining two optical fibers end-to-end. The goal is to fuse the two fibers together in such a way that light passing through the fibers is not scattered or reflected back by the splice, and so that the splice and the region surrounding it are almost as strong as the intact fiber.
-
product
Fuse Tools
*Three functions in one tool, voltage detector, fuse puller and spotlights*Single range 4kV to 12kV line-to-line voltage detector*Provides an audible and visual alarm when voltage is detected*Bright white LED spotlights provide illumination in dark situations*Compact and lightweight solution for added safety and flexibility
