Control Systems
-
product
Car-to-X Signal Strength Emulator
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
LXI Matrix Switching Unit
ProDAQ 6140
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
product
Thermal Division Overview
MPI Thermal is a division of MPI Corporation. With over 60 years of combined thermal control system experience with our international engineering teams, this has brought about a comprehensive product portfolio of thermal air stream systems for today's manufacturer's environmental test chamber needs.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm - SPST
50-294-111
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
LCF3 Software
Provides system control, data acquisition, real-time graphs, calculation of results, storage of data to disk, and post test graphs and reports in accordance with the relevant sections of ASTM E606-04, BS 7270 (2006), and ISO 12106 (2003).
-
product
PCI Express x4, Gen3 XMC Carrier
TPCE278
The TPCE278 is a standard height PCI Express Revision 3.0 compatible module that provides one slot for a single-width XMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE278 is a versatile solution to upgrade well known XMC I/O solutions to the PCI Express signalling standard. The PCI Express x4 link from the host board to the XMC module is enhanced by a PCIe Gen3 Redriver, allowing safe operation of XMC modules on PCIe mainboards.
-
product
Acoustic Control System
m+p VibControl performs acoustic testing in reverberation chambers and direct field environments as well as progressive wave tube testing. It is a fully automatic digital control system, providing fast, accurate and repeatable control of high-level noise to a reference octave band spectrum and the overall sound pressure level (OASPL). The control guarantees a high level of product safety.
-
product
Airlock Control System
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
product
AM Control System
Clamir
*Continuous monitoring of melt pool dynamics and geometry.*Ensures quality and repeatability.*Compatible with most laser heads.*Compatible with a wide range of materials.*Easy mechanical integration.*Quick configuration.*Helps to reduce CO2 emissions.
-
product
SparkFun Humidity And Temperature Sensor Breakout
Si7021
The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system. All you need are two lines for I2C communication, and you’ll have relative humidity readings and very accurate temperature readings as a bonus!
-
product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784399-01
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
product
Syringe Pump
65x
The 65x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter to 25 mL/min. Exceptional low-flow stability at up to 20,000 psi (1,390 bar) makes this the ideal pump for high pressure applications from deep well core analysis and polymer extrusions. The 65x pumps to the lowest flow rates with zero pulsation available on the market!The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 65x pump module has a single-ratio drive train with autolubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases. Continuous pumping is available in either single or dual pumping system controlled via air valves, offering zero pulsation for unlimited delivery. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
product
3U / 6U PXIe Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
product
Machine Controllers
The flexible design of Yaskawa machine controllers allows cost-effective configuration of motion control for any sized automation system. Controllers can be easily adapted for stand-alone use on a single axis, for networking with other control devices or for complete control of a multi-axis machine.
-
product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Software Development Projects
Precision Development Consulting Inc
Automation of new process tool prototype in startup environment, Complex R&D Gasbox Automation, Semiconductor System Control Software, Wafer Transfer Control Software, 300mm Factory Automation, Complete port of Spectrometer software to windows, HSMS Protocol
-
product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
product
Test Container
MTL 15 | VP 700006
Maschinenbau Haldenwang GmbH & Co. KG.
The MTL 15 test container works completely independently thanks to the optionally available, fully integrated power generator. Equipped with a hydraulic set-down device including cable remote control, the test system can be set up within 15 minutes and is therefore ideal for changing locations.
-
product
PCI 32 Channel TTL Digital Interface
8010
The 8010 PCI digital I/O interface provides 32 channels of buffered drive digital I/O, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
product
AWD Dynamometers
MD-AWD-500-AC/EC-100/250
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
product
Temperature and Humidity Sensor, Cresnet
C2N-RTHS
The C2N-RTHS is a wall-mounted temperature and relative humidity sensor that communicates directly with any 2-Series control system via the Cresnet control network. One-piece mounting makes the C2N-RTHS simple to install. The 1-1/2 inch diameter face protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
product
IOLITE
IOLITE - Data Acquisition and Real-time Control SystemData acquisition and real-time control front-end system with dual EtherCAT buses for industrial testing applications. All-in-one solution for real-time control and feedback monitoring.
-
product
Industrial Standby Battery Monitoring Systems
Batteries are the power storage medium for all Power Rectifier and UPS Systems. Modern Rectifiers and UPS control systems generally supply the user with only a summary of the condition of the associated power systems, however Battery Monitoring systems specifically measure, record and analyse the individual cell and battery module parameters in detail.
-
product
High-performance PXI System
M5000 Series
The M5000 Series forms the backbone for the Keysight Quantum Control System (QCS) – complete digital solution that eliminates the need to design custom control solutions. Analog LOs and mixers in traditional hardware used for quantum control require frequent calibration, introduce leakage noise, and contribute to slow drifts in the performance of the system. The Keysight M5000 Series fully eliminates the need for these components leading to enhanced ease-of-use, unrivaled noise performance, and improved long-term stability.
-
product
Wide FOV Target Projector
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
product
System Integration Services
Systems integration services to meet a wide variety of industrial needs. It includes the following key expertise: Desktop, Embedded Simulation and Real-time system, Data Acquisition and Report generation/extraction, Factory automation, Testing, Control and Monitoring system, Vision inspection, Equipment calibration, Special purpose machine, and many more.
