PCMCIA Interfaces
-
Product
Multi-Channel, Multi-Protocol 1553, ARINC, WMUX Interface for 3U PXIe
-
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
-
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Enhanced Serial Interface Module for Excalibur 8000 Family of Carrier Boards, with High Baud Rate & High Throughput
M8KSerial
-
The M8KSerial is an enhanced serial interface module for the multiprotocol Excalibur 8000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to two independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M8KSerial module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 8000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M8KSerial module is supplied with C drivers, including source code.
-
Product
Quad Port Fiber 25GbE Ethernet PCI Express Server Adapter With Intel E810-CAM1. Ideal For Data Center Networking And Storage Area Networks.
PCIE-2531NP
-
Intel E810 Controller4 25GbE SFP28 portsPCIe Gen. 4 x16 host interfaceLow profile (half length) form factorsSupports SR-IOV based virtualization
-
Product
Interface
P-SER
-
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
Product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-03
-
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
4x 3U OpenVPX MOSA Remote Interface Unit
SIU34-RIUVARM-01
-
SIU34-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RUI) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
Product
In-Line 1553 Ethernet Converter
NLINE-E1553
-
Full BC, RT, and BM 1553 Controls Built-in a Small, Rugged, In-Line package. Control and convert 1553 messages to/from Ethernet in real-time (<20 uSec). Auto-bridge 1553 messages (BM) to UDP Ethernet without any programming.
-
Product
ARINC PCI Express 4 Lane Interface Cards
PCIE4L-A429
-
Alta Data Technologies’ PCIE4L-A429 interface module offers a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal. The 4 lane card (PCIE4L) is normal 1/2 height common for most desktop and larger server systems.
-
Product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
-
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
Product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
-
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Ethernet to CAN Bus Gateway
YAV90090
-
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
Product
Interface
RXMC1553
-
Abaco Systems’ RXMC-1553 is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II on a XMC.0 Mezzanine Card. With one or two dual-redundant channels, the RXMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
10 Gbit Ethernet Card, PXIe Form Factor
ADQ10GBE
-
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
-
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
Optical Head Interface
N7749C
-
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
-
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
PXI-8430/2 , 2-Port, RS232 PXI Serial Interface Module
778982-01
-
2-Port, RS232 PXI Serial Interface Module - The PXI‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports … for compatibility with programs that use serial communications.
-
Product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
-
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-4x10GBASE-T
-
- Support up to four 10GbE copper interfaces (10GBASE-T)- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
Product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
-
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
-
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
10GBASE-T Network Adapter Card
-
- Supports up to four 10GbE copper interface (10GBASE-T)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Flight-Certifiable Avionics Interface
RAR15XC
-
The RAR15XC flight-certifiable avionics communications board delivers high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O. Its small XMC mezzanine form factor is easily integrated onto other compatible boards, like the SBC314C flight-certifiable single board computer.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
-
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Remote Controller
-
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
Product
PCI Mezzanine Card
PNIC1G
-
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
